Pablo Santamarina Guerrero
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Pablo Santamarina Guerrero has a total of 206 co-authors. Here are the top co-authors by number of shared publications:
- David Orozco Suarez
Instituto de Astrofisica de Andalucía
11 shared publications - Achim Gandorfer
Max-Planck-Institut für Sonnensystemforschung
9 shared publications - Alberto Álvarez-Herrero
Instituto Nacional de Técnica Aeroespacial (INTA), Madrid, Spain
9 shared publications - Alex Feller
Max-Planck-Institut für Sonnensystemforschung
9 shared publications - Francisco Javier Bailén
Instituto de Astrofisica de Andalucía
9 shared publications - Jose Carlos del Toro Iniesta
Instituto de Astrofisica de Andalucía
9 shared publications
Latest Publications
- Open Access
- 20 October 2026
- Published by American Astronomical Society in The Astrophysical Journal Letters
- Vol. 1010 (2) , L43
A Forest of Emission Lines Observed by Sunrise III/SUSI above the Solar Limb
We present off-limb spectroscopy using low-stray-light data from the Sunrise Spectropolarimeter and Imager (SUSI) on board the S unrise iii stratospheric solar observatory. A spatial scan with SUSI’s slit almost parallel to the local limb reached from within the solar disk to 6.5 Mm off-limb. The wavelength range spanned from 407.6 to 410.25 nm. We detected a total of 174 spectral lines in emission off-limb, a 2.5-fold increase over previous reports. Surprisingly, 122 of these lines begin to appear in emission already on the disk, although close to the limb. In addition, one-fifth of relatively prominent emission lines are due to rare-earth and heavy elements and molecules, where the absorption lines of these transitions are typically weak on-disc.
- 20 October 2026
- Published by American Astronomical Society in The Astrophysical Journal Letters
- Vol. 1010 (2) , L43
Open AccessA Forest of Emission Lines Observed by Sunrise III/SUSI above the Solar Limb
We present off-limb spectroscopy using low-stray-light data from the Sunrise Spectropolarimeter and Imager (SUSI) on board the S unrise iii stratospheric solar observatory. A spatial scan with SUSI’s slit almost parallel to the local limb reached from within the solar disk to 6.5 Mm off-limb. The wavelength range spanned from 407.6 to 410.25 nm. We detected a total of 174 spectral lines in emission off-limb, a 2.5-fold increase over previous reports. Surprisingly, 122 of these lines begin to appear in emission already on the disk, although close to the limb. In addition, one-fifth of relatively prominent emission lines are due to rare-earth and heavy elements and molecules, where the absorption lines of these transitions are typically weak on-disc.
- Open Access
- 4 August 2026
- Published by Springer Nature in Solar Physics
- Vol. 301 (8) , 116
Polarimetric Calibration of the Tunable Magnetograph for the Sunrise III Mission
- 4 August 2026
- Published by Springer Nature in Solar Physics
- Vol. 301 (8) , 116
Open AccessPolarimetric Calibration of the Tunable Magnetograph for the Sunrise III Mission
- Open Access
- 10 July 2026
- Published by American Astronomical Society in The Astrophysical Journal Letters
- Vol. 1005 (2) , L66
Vector Magnetic Field Associated with an Active Region Filament Observed by S unrise III /SCIP in the Ca II 8542 Å Line
We report high-spatial-resolution spectropolarimetric observations spatially associated with a solar filament, obtained with the S unrise Chromospheric Infrared Spectro-Polarimeter (SCIP) on board the S unrise iii balloon-borne solar observatory on 2024 July 15. The observed filament was located near the solar disk center, adjacent to an active region, and remained quiescent for at least 2 hr during the observing period. SCIP recorded full Stokes profiles in the Ca ii 8542 Å line, revealing clear signatures of linear polarization produced by the transverse Zeeman effect. The detected linear polarization signals within the filament region exceeded the 2 σ noise level and exhibited a characteristic Zeeman double-lobe spectral shape that distinguishes them from polarization due to scattering. The magnetic field strength derived using the weak field approximation is approximately −80 G along the line of sight and 300–500 G in the transverse direction. These values likely reflect the magnetic properties of the filament and its supporting chromospheric environment. The orientation of the magnetic field vector is nearly parallel to the filament axis in its northeastern portion, while the southeastern part of the filament extends outside the field of view. To our knowledge, this is the first unambiguous detection of linear polarization associated with a solar filament with the Ca ii 8542 Å line. Our results open a new diagnostic window to the vector magnetic structure of solar filaments in the lower chromosphere, complementing existing He i based diagnostics that probe the upper chromosphere.
- 10 July 2026
- Published by American Astronomical Society in The Astrophysical Journal Letters
- Vol. 1005 (2) , L66
Open AccessVector Magnetic Field Associated with an Active Region Filament Observed by S unrise III /SCIP in the Ca II 8542 Å Line
We report high-spatial-resolution spectropolarimetric observations spatially associated with a solar filament, obtained with the S unrise Chromospheric Infrared Spectro-Polarimeter (SCIP) on board the S unrise iii balloon-borne solar observatory on 2024 July 15. The observed filament was located near the solar disk center, adjacent to an active region, and remained quiescent for at least 2 hr during the observing period. SCIP recorded full Stokes profiles in the Ca ii 8542 Å line, revealing clear signatures of linear polarization produced by the transverse Zeeman effect. The detected linear polarization signals within the filament region exceeded the 2 σ noise level and exhibited a characteristic Zeeman double-lobe spectral shape that distinguishes them from polarization due to scattering. The magnetic field strength derived using the weak field approximation is approximately −80 G along the line of sight and 300–500 G in the transverse direction. These values likely reflect the magnetic properties of the filament and its supporting chromospheric environment. The orientation of the magnetic field vector is nearly parallel to the filament axis in its northeastern portion, while the southeastern part of the filament extends outside the field of view. To our knowledge, this is the first unambiguous detection of linear polarization associated with a solar filament with the Ca ii 8542 Å line. Our results open a new diagnostic window to the vector magnetic structure of solar filaments in the lower chromosphere, complementing existing He i based diagnostics that probe the upper chromosphere.
- Open Access
- 9 July 2026
- Published by American Astronomical Society in The Astrophysical Journal Letters
- Vol. 1005 (2) , L64
S unrise iii : Instrument, Mission, Data, and First Results
S unrise iii is a stratospheric balloon-borne solar observatory with a 1 m diameter telescope and three postfocus instruments, along with an image stabilisation system, all within a protective gondola. It samples the lower solar atmosphere, from the solar surface to the middle chromosphere, at a resolution approaching 50 km on the Sun. S unrise iii flew successfully for 6.5 days suspended from a zero-pressure stratospheric balloon from northern Sweden to northwestern Canada in 2024 July, gathering around 200 TB of data. The present issue of the Astrophysical Journal Letters focuses on the first scientific results from the data collected during that flight. This Letter introduces this Focus Issue, providing a very brief overview of the capabilities of the instrumentation, the flight, and of the gathered data. Challenges for the measurements, data reduction, and interpretation are also briefly touched upon. The Letter ends with an overview of the first set of science results obtained from these data, as presented in the current Focus Issue.
- 9 July 2026
- Published by American Astronomical Society in The Astrophysical Journal Letters
- Vol. 1005 (2) , L64
Open AccessS unrise iii : Instrument, Mission, Data, and First Results
S unrise iii is a stratospheric balloon-borne solar observatory with a 1 m diameter telescope and three postfocus instruments, along with an image stabilisation system, all within a protective gondola. It samples the lower solar atmosphere, from the solar surface to the middle chromosphere, at a resolution approaching 50 km on the Sun. S unrise iii flew successfully for 6.5 days suspended from a zero-pressure stratospheric balloon from northern Sweden to northwestern Canada in 2024 July, gathering around 200 TB of data. The present issue of the Astrophysical Journal Letters focuses on the first scientific results from the data collected during that flight. This Letter introduces this Focus Issue, providing a very brief overview of the capabilities of the instrumentation, the flight, and of the gathered data. Challenges for the measurements, data reduction, and interpretation are also briefly touched upon. The Letter ends with an overview of the first set of science results obtained from these data, as presented in the current Focus Issue.
- Open Access
- 30 March 2026
- Published by EDP Sciences in Astronomy & Astrophysics
- Vol. 708, A85
Jitter sensing and reconstruction from temporal series of solar images: Applications to TuMag
Context. Images recorded with the Tunable Magnetograph (TuMag) instrument on board the S UNRISE III balloon observatory are affected by temporal contrast fluctuations. These variations are related to high-frequency vibrations (jitter) of the platform that cannot be entirely compensated by the image stabilization unit of the telescope. Jitter smooths out mid- to high-frequency details and degrades the contrast of images that are integrated over hundreds of milliseconds to achieve the signal-to-noise levels required by the instrument. The temporal variations of jitter hamper the reconstruction of the data and limit the accuracy of the instrument. Aims. We present a technique that allows us to infer and compensate temporal changes of the amplitude and direction of jitter from two images of the same scene, provided they are recorded close enough in time to prevent the scene from evolving significantly. Methods. We assess the performance of our method through a dynamical magnetohydrodynamical simulation of the solar scene that is degraded with diffraction effects, noise, and jitter. We evaluate the performance of the algorithm as a function of the jitter amplitude and as a function of the time gap between the two images. We finally apply it to a time series recorded by TuMag to sense and restore the temporal evolution of jitter on the images. Results. Our numerical experiments show that the algorithm is able to sense jitter with an accuracy better than 0.″005 (≲0.1 px) for images recorded less than 10 s apart and assuming a worst-case scenario with a low signal-to-noise ratio of 100 and induced rms jitter amplitudes as large as 0.″15 in the X and Y directions. When increasing the time interval to 30 s, the errors found are still below 0.″01. For the chosen TuMag series we find that the jitter rms amplitudes vary strongly within the range 0.″05–0.″15 (∼1–4 px) and are anticorrelated to the contrast of the recorded images. Correction of jitter improves the contrast of wavefront-reconstructed images by 2.5% in some cases and reduces the rms variation of contrast along the series by half.
- 30 March 2026
- Published by EDP Sciences in Astronomy & Astrophysics
- Vol. 708, A85
Open AccessJitter sensing and reconstruction from temporal series of solar images: Applications to TuMag
Context. Images recorded with the Tunable Magnetograph (TuMag) instrument on board the S UNRISE III balloon observatory are affected by temporal contrast fluctuations. These variations are related to high-frequency vibrations (jitter) of the platform that cannot be entirely compensated by the image stabilization unit of the telescope. Jitter smooths out mid- to high-frequency details and degrades the contrast of images that are integrated over hundreds of milliseconds to achieve the signal-to-noise levels required by the instrument. The temporal variations of jitter hamper the reconstruction of the data and limit the accuracy of the instrument. Aims. We present a technique that allows us to infer and compensate temporal changes of the amplitude and direction of jitter from two images of the same scene, provided they are recorded close enough in time to prevent the scene from evolving significantly. Methods. We assess the performance of our method through a dynamical magnetohydrodynamical simulation of the solar scene that is degraded with diffraction effects, noise, and jitter. We evaluate the performance of the algorithm as a function of the jitter amplitude and as a function of the time gap between the two images. We finally apply it to a time series recorded by TuMag to sense and restore the temporal evolution of jitter on the images. Results. Our numerical experiments show that the algorithm is able to sense jitter with an accuracy better than 0.″005 (≲0.1 px) for images recorded less than 10 s apart and assuming a worst-case scenario with a low signal-to-noise ratio of 100 and induced rms jitter amplitudes as large as 0.″15 in the X and Y directions. When increasing the time interval to 30 s, the errors found are still below 0.″01. For the chosen TuMag series we find that the jitter rms amplitudes vary strongly within the range 0.″05–0.″15 (∼1–4 px) and are anticorrelated to the contrast of the recorded images. Correction of jitter improves the contrast of wavefront-reconstructed images by 2.5% in some cases and reduces the rms variation of contrast along the series by half.
- Open Access
- 28 October 2025
- Published by Springer Nature in Solar Physics
- Vol. 300 (10) , 1-52
TuMag: The Tunable Magnetograph for the Sunrise III Mission
Sunrise iii is a balloon-borne solar observatory dedicated to the investigation of the processes governing the physics of the magnetic field and the plasma flows in the lower solar atmosphere. The gondola hosts a 1-m aperture telescope that feeds three post-focus instruments. One of these instruments, the Tunable Magnetograph (TuMag), is a tunable imaging spectropolarimeter in visible wavelengths. It is designed to probe the vector magnetic field, $\bf{B}$ , and the line-of-sight (LoS) velocity, $v_{\mathrm{LoS}}$ , of the photosphere and the lower chromosphere. It provides polarized images with a $63^{\prime \prime }\times \, 63^{\prime \prime }$ field of view (FoV) of the Sun in four polarization states. These images can later be processed on ground to retrieve maps of the aforementioned solar physical quantities. The quasi-simultaneous observation of two spectral lines sensitive to $\bf{B}$ and $v_{\mathrm{LoS}}$ in the photosphere and lower chromosphere provides excellent diagnostic measurements of the magnetic and dynamic coupling in these layers. When combined with the other two instruments on board, observing in the infrared and ultraviolet regions of the spectrum, TuMag’s diagnostic potential is expected to be greatly enhanced. Building upon heritage of instruments like IMaX and SO/PHI, the key technologies employed for TuMag are a liquid-crystal-variable-retarder-based polarimeter and a solid, LiNbO 3 Fabry–Pérot etalon as a spectrometer. However, it also incorporates several innovative features, such as in-house-made, high-sensitivity scientific cameras and a double filter wheel. The latter makes TuMag the first balloon-borne instrument of its type capable of tuning between spectral lines. Specifically, it can sequentially observe any two out of the three spectral lines of Fe i at 525.02 and 525.06 nm and of Mg i at 517.3 nm. Time cadences range from 30 to 100 seconds, depending on the observing mode and the specific pair of spectral lines targeted. Laboratory measurements have demonstrated good image quality, spectral resolution, and polarimetric efficiency. Here we report on the concept, design, calibration, and integration phases of the instrument, as well as on the data reduction pipeline.- 28 October 2025
- Published by Springer Nature in Solar Physics
- Vol. 300 (10) , 1-52
Open AccessTuMag: The Tunable Magnetograph for the Sunrise III Mission
Sunrise iii is a balloon-borne solar observatory dedicated to the investigation of the processes governing the physics of the magnetic field and the plasma flows in the lower solar atmosphere. The gondola hosts a 1-m aperture telescope that feeds three post-focus instruments. One of these instruments, the Tunable Magnetograph (TuMag), is a tunable imaging spectropolarimeter in visible wavelengths. It is designed to probe the vector magnetic field, $\bf{B}$ , and the line-of-sight (LoS) velocity, $v_{\mathrm{LoS}}$ , of the photosphere and the lower chromosphere. It provides polarized images with a $63^{\prime \prime }\times \, 63^{\prime \prime }$ field of view (FoV) of the Sun in four polarization states. These images can later be processed on ground to retrieve maps of the aforementioned solar physical quantities. The quasi-simultaneous observation of two spectral lines sensitive to $\bf{B}$ and $v_{\mathrm{LoS}}$ in the photosphere and lower chromosphere provides excellent diagnostic measurements of the magnetic and dynamic coupling in these layers. When combined with the other two instruments on board, observing in the infrared and ultraviolet regions of the spectrum, TuMag’s diagnostic potential is expected to be greatly enhanced. Building upon heritage of instruments like IMaX and SO/PHI, the key technologies employed for TuMag are a liquid-crystal-variable-retarder-based polarimeter and a solid, LiNbO 3 Fabry–Pérot etalon as a spectrometer. However, it also incorporates several innovative features, such as in-house-made, high-sensitivity scientific cameras and a double filter wheel. The latter makes TuMag the first balloon-borne instrument of its type capable of tuning between spectral lines. Specifically, it can sequentially observe any two out of the three spectral lines of Fe i at 525.02 and 525.06 nm and of Mg i at 517.3 nm. Time cadences range from 30 to 100 seconds, depending on the observing mode and the specific pair of spectral lines targeted. Laboratory measurements have demonstrated good image quality, spectral resolution, and polarimetric efficiency. Here we report on the concept, design, calibration, and integration phases of the instrument, as well as on the data reduction pipeline. - Top Cited PapersOpen Access
- 30 May 2025
- Published by Springer Nature in Solar Physics
- Vol. 300 (5) , 1-70
Sunrise iii: Overview of Observatory and Instruments
In July 2024, Sunrise completed its third successful science flight. The Sunrise iii observatory had been upgraded significantly after the two previous successful flights in 2009 and 2013, to tackle the most recent science challenges concerning the solar atmosphere. Three completely new instruments focus on the small-scale physical processes and their complex interaction from the deepest observable layers in the photosphere up to chromospheric heights. Previously poorly explored spectral regions and lines are exploited to paint a three-dimensional picture of the solar atmosphere with unprecedented completeness and level of detail. The full polarimetric information is captured by all three instruments to reveal the interaction between the magnetic fields and the hydrodynamic processes. Two slit-based spectropolarimeters, the Sunrise UV Spectropolarimeter and Imager (SUSI) and the Sunrise Chromospheric Infrared spectro-Polarimeter (SCIP), focus on the near-ultraviolet (309 – 417 nm) and the near-infrared (765 – 855 nm) regions respectively, and the imaging spectropolarimeter Tunable Magnetograph (TuMag) simultaneously obtains maps of the full field-of-view of $46\times 46$ Mm2 in the photosphere and the chromosphere in the visible (525 and 517 nm). The instruments are operated in an orchestrated mode, benefiting from a new Image Stabilization and Light Distribution unit (ISLiD), with the Correlating Wavefront Sensor (CWS) providing the autofocus control and an image stability with a root-mean-square value smaller than 0.005”. A new gondola was constructed to significantly improve the telescope pointing stability, required to achieve uninterrupted observations over many hours. Sunrise iii was launched successfully on 10 July 2024, from the Esrange Space Center of the Swedish Space Corporation near Kiruna (Sweden). It reached the landing site between the Mackenzie River and the Great Bear Lake in Canada after a flight duration of 6.5 days. In this paper, we give an overview of the Sunrise iii observatory and its instruments.- 30 May 2025
- Published by Springer Nature in Solar Physics
- Vol. 300 (5) , 1-70
Top Cited PapersOpen AccessSunrise iii: Overview of Observatory and Instruments
In July 2024, Sunrise completed its third successful science flight. The Sunrise iii observatory had been upgraded significantly after the two previous successful flights in 2009 and 2013, to tackle the most recent science challenges concerning the solar atmosphere. Three completely new instruments focus on the small-scale physical processes and their complex interaction from the deepest observable layers in the photosphere up to chromospheric heights. Previously poorly explored spectral regions and lines are exploited to paint a three-dimensional picture of the solar atmosphere with unprecedented completeness and level of detail. The full polarimetric information is captured by all three instruments to reveal the interaction between the magnetic fields and the hydrodynamic processes. Two slit-based spectropolarimeters, the Sunrise UV Spectropolarimeter and Imager (SUSI) and the Sunrise Chromospheric Infrared spectro-Polarimeter (SCIP), focus on the near-ultraviolet (309 – 417 nm) and the near-infrared (765 – 855 nm) regions respectively, and the imaging spectropolarimeter Tunable Magnetograph (TuMag) simultaneously obtains maps of the full field-of-view of $46\times 46$ Mm2 in the photosphere and the chromosphere in the visible (525 and 517 nm). The instruments are operated in an orchestrated mode, benefiting from a new Image Stabilization and Light Distribution unit (ISLiD), with the Correlating Wavefront Sensor (CWS) providing the autofocus control and an image stability with a root-mean-square value smaller than 0.005”. A new gondola was constructed to significantly improve the telescope pointing stability, required to achieve uninterrupted observations over many hours. Sunrise iii was launched successfully on 10 July 2024, from the Esrange Space Center of the Swedish Space Corporation near Kiruna (Sweden). It reached the landing site between the Mackenzie River and the Great Bear Lake in Canada after a flight duration of 6.5 days. In this paper, we give an overview of the Sunrise iii observatory and its instruments. - Open Access
- 5 August 2024
- Published by EDP Sciences in Astronomy & Astrophysics
- Vol. 688, A67
Correcting Fabry-Pérot etalon effects in solar observations
Context. Data processing pipelines of Fabry–Pérot interferometers (FPI) must take into account the side effects these devices introduce in the observations. Interpretation of these observations without proper correction can lead to inaccurate or false results, with consequent impact on their physical interpretation. Corrections typically require prior knowledge of the properties of the etalon and the way they affect the incoming light in order to calibrate the data successfully. Aims. We have developed an algorithm to derive etalon properties from flat-field observations and tested its applicability and accuracy using simulated observations and real measurements. Methods. We employed analytical expressions of the transmission profiles for FPIs in collimated and telecentric configurations to derive their expected impact on the observations. These analytical expressions allowed us to develop a customized optimization algorithm capable of inferring the properties of the etalon from the observations. The algorithm’s performance has been tested on simulated observations with an etalon in collimated and telecentric setups employing various noise levels and spectral samplings. Additionally, we explored how tilting the etalon in a telecentric configuration influences the algorithm’s effectiveness. Lastly, we also applied the algorithm to a set of real flat-field observations taken with the high-resolution telescope of the Polarimetric and Helioseismic Imager on board the Solar Orbiter mission (HRT-SO/PHI). Results. The algorithm is able to retrieve the gain and etalon induced transmission velocity shifts (cavity map), with an average accuracy ranging between 0.4% and 0.1% for the former and between 120 m s−1 and 30 m s−1 for the latter. Both reducing the noise level and increasing the spectral sampling of the observations proved to greatly increase the algorithm’s performance, as expected. Results also suggest that determination of the observed object from the data is possible but an additional error between 40 m s−1 and 10 m s−1 is to be expected in the inferred cavity map. Furthermore, we show that neglecting the asymmetries arising from either tilts of the etalon or imperfections in the telecentrism can lead to large errors when determining the gain. Tests with HRT-SO/PHI data have verified the applicability of the algorithm in real cases. Conclusions. Our presented method enabled us to derive the transmission profile of FPIs from observations of collimated and telecentric configurations. It has proven to be robust against the presence of noise and limited spectral line sampling. The results reported here also show the importance of accounting for the asymmetries arising in real telecentric mounts when interpreting the results of real instruments.
- 5 August 2024
- Published by EDP Sciences in Astronomy & Astrophysics
- Vol. 688, A67
Open AccessCorrecting Fabry-Pérot etalon effects in solar observations
Context. Data processing pipelines of Fabry–Pérot interferometers (FPI) must take into account the side effects these devices introduce in the observations. Interpretation of these observations without proper correction can lead to inaccurate or false results, with consequent impact on their physical interpretation. Corrections typically require prior knowledge of the properties of the etalon and the way they affect the incoming light in order to calibrate the data successfully. Aims. We have developed an algorithm to derive etalon properties from flat-field observations and tested its applicability and accuracy using simulated observations and real measurements. Methods. We employed analytical expressions of the transmission profiles for FPIs in collimated and telecentric configurations to derive their expected impact on the observations. These analytical expressions allowed us to develop a customized optimization algorithm capable of inferring the properties of the etalon from the observations. The algorithm’s performance has been tested on simulated observations with an etalon in collimated and telecentric setups employing various noise levels and spectral samplings. Additionally, we explored how tilting the etalon in a telecentric configuration influences the algorithm’s effectiveness. Lastly, we also applied the algorithm to a set of real flat-field observations taken with the high-resolution telescope of the Polarimetric and Helioseismic Imager on board the Solar Orbiter mission (HRT-SO/PHI). Results. The algorithm is able to retrieve the gain and etalon induced transmission velocity shifts (cavity map), with an average accuracy ranging between 0.4% and 0.1% for the former and between 120 m s−1 and 30 m s−1 for the latter. Both reducing the noise level and increasing the spectral sampling of the observations proved to greatly increase the algorithm’s performance, as expected. Results also suggest that determination of the observed object from the data is possible but an additional error between 40 m s−1 and 10 m s−1 is to be expected in the inferred cavity map. Furthermore, we show that neglecting the asymmetries arising from either tilts of the etalon or imperfections in the telecentrism can lead to large errors when determining the gain. Tests with HRT-SO/PHI data have verified the applicability of the algorithm in real cases. Conclusions. Our presented method enabled us to derive the transmission profile of FPIs from observations of collimated and telecentric configurations. It has proven to be robust against the presence of noise and limited spectral line sampling. The results reported here also show the importance of accounting for the asymmetries arising in real telecentric mounts when interpreting the results of real instruments.
- Open Access
- 30 April 2024
- Published by EDP Sciences in Astronomy & Astrophysics
- Vol. 685, A28
Comparison of magnetic data products from Solar Orbiter SO/PHI-FDT and SDO/HMI
Context.The Polarimetric and Helioseismic Imager (SO/PHI), on board the Solar Orbiter mission, is the first photospheric magnetograph and tachograph to observe the Sun from outside the Sun-Earth line. The Full Disc Telescope (FDT) of SO/PHI, images the whole solar disk with a spatial resolution that varies with the distance between the Sun and the spacecraft.Aims.We check for consistency between the magnetic field strength (B), the field inclination (γ), the line-of-sight (LoS) magnetic component (BLoS) and the field azimuth (ϕ), inferred by SO/PHI-FDT and the Helioseismic and Magnetic Imager (HMI), on board Solar Dynamics Observatory (SDO), and obtain linear correlation coefficients among them.Methods.We use data from both instruments obtained on 8 March 2022, when the angle between SDO and Solar Orbiter was 3.4° and the solar disk showed four developed active regions. Before comparing the magnetic field products of both instruments we perform a precise alignment of the data, including a matching of the plate scale. Further, in order to improve the homogeneity of the compared data products, the SDO/HMI data were convolved with the SO/PHI-FDT point spread function (PSF). The linear correlation coefficients are obtained through a linear regression of SDO/HMI to SO/PHI-FDT.Results.The two instruments yield comparable magnetic field data products. The slope coefficients for a linear fit are 1.37 forB, 1.11 forγ, 1.35 forBLoSand 1 for the azimuth. The corresponding fit offsets are −94 G, −9.8°, 5.2 G and 0.1°, respectively. The agreement between both instruments is significantly better when we take into account the different spatial resolution of both instruments. The fitting results vary slightly depending on the analyzed active region except for one of the four active regions, which shows larger differences and has been excluded from the comparison. The comparison of the LoS magnetic field products from SDO/HMI at 45 s and 720 s with SO/PHI-FDT shows a slope value of 1.17, with the offset less than 6 G, in both cases.
- 30 April 2024
- Published by EDP Sciences in Astronomy & Astrophysics
- Vol. 685, A28
Open AccessComparison of magnetic data products from Solar Orbiter SO/PHI-FDT and SDO/HMI
Context.The Polarimetric and Helioseismic Imager (SO/PHI), on board the Solar Orbiter mission, is the first photospheric magnetograph and tachograph to observe the Sun from outside the Sun-Earth line. The Full Disc Telescope (FDT) of SO/PHI, images the whole solar disk with a spatial resolution that varies with the distance between the Sun and the spacecraft.Aims.We check for consistency between the magnetic field strength (B), the field inclination (γ), the line-of-sight (LoS) magnetic component (BLoS) and the field azimuth (ϕ), inferred by SO/PHI-FDT and the Helioseismic and Magnetic Imager (HMI), on board Solar Dynamics Observatory (SDO), and obtain linear correlation coefficients among them.Methods.We use data from both instruments obtained on 8 March 2022, when the angle between SDO and Solar Orbiter was 3.4° and the solar disk showed four developed active regions. Before comparing the magnetic field products of both instruments we perform a precise alignment of the data, including a matching of the plate scale. Further, in order to improve the homogeneity of the compared data products, the SDO/HMI data were convolved with the SO/PHI-FDT point spread function (PSF). The linear correlation coefficients are obtained through a linear regression of SDO/HMI to SO/PHI-FDT.Results.The two instruments yield comparable magnetic field data products. The slope coefficients for a linear fit are 1.37 forB, 1.11 forγ, 1.35 forBLoSand 1 for the azimuth. The corresponding fit offsets are −94 G, −9.8°, 5.2 G and 0.1°, respectively. The agreement between both instruments is significantly better when we take into account the different spatial resolution of both instruments. The fitting results vary slightly depending on the analyzed active region except for one of the four active regions, which shows larger differences and has been excluded from the comparison. The comparison of the LoS magnetic field products from SDO/HMI at 45 s and 720 s with SO/PHI-FDT shows a slope value of 1.17, with the offset less than 6 G, in both cases.
- Open Access
- 1 March 2024
- Published by American Astronomical Society in The Astrophysical Journal
- Vol. 964 (1) , 32
Persistent Homology Analysis for Solar Magnetograms
Understanding the magnetic fields of the Sun is essential for unraveling the underlying mechanisms driving solar activity. Integrating topological data analysis techniques into these investigations can provide valuable insights into the intricate structures of magnetic fields, enhancing our comprehension of solar activity and its implications. In this study, we explore what persistent homology can offer in the analysis of solar magnetograms, with the objective of introducing a novel tool that will serve as the foundation for further studies of magnetic structures at the solar surface. By combining various filtration methods of the persistent homology analysis, we conduct an analysis of solar magnetograms that captures the broad magnetic scene, involving a mixture of positive and negative polarities. This analysis is applied to observations of both quiet-Sun and active regions, taken with the Hinode/Solar Optical Telescope and SDO/Helioseismic and Magnetic Imager, respectively. Our primary focus is on analyzing the properties of the spatial structures and features of the magnetic fields identified through these techniques. The results show that persistent diagrams can encode the spatial structural complexity of the magnetic flux of active regions by identifying the isolated, connected, and interacting features. They facilitate the classification of active regions based on their morphology and the detection and quantification of interacting structures of opposing polarities, such as δ spots. The small-scale events in the quiet Sun, such as magnetic flux cancellation and emergence, are also revealed in persistent diagrams and can be studied by observing the evolution of the plots and tracking the relevant features.
- 1 March 2024
- Published by American Astronomical Society in The Astrophysical Journal
- Vol. 964 (1) , 32
Open AccessPersistent Homology Analysis for Solar Magnetograms
Understanding the magnetic fields of the Sun is essential for unraveling the underlying mechanisms driving solar activity. Integrating topological data analysis techniques into these investigations can provide valuable insights into the intricate structures of magnetic fields, enhancing our comprehension of solar activity and its implications. In this study, we explore what persistent homology can offer in the analysis of solar magnetograms, with the objective of introducing a novel tool that will serve as the foundation for further studies of magnetic structures at the solar surface. By combining various filtration methods of the persistent homology analysis, we conduct an analysis of solar magnetograms that captures the broad magnetic scene, involving a mixture of positive and negative polarities. This analysis is applied to observations of both quiet-Sun and active regions, taken with the Hinode/Solar Optical Telescope and SDO/Helioseismic and Magnetic Imager, respectively. Our primary focus is on analyzing the properties of the spatial structures and features of the magnetic fields identified through these techniques. The results show that persistent diagrams can encode the spatial structural complexity of the magnetic flux of active regions by identifying the isolated, connected, and interacting features. They facilitate the classification of active regions based on their morphology and the detection and quantification of interacting structures of opposing polarities, such as δ spots. The small-scale events in the quiet Sun, such as magnetic flux cancellation and emergence, are also revealed in persistent diagrams and can be studied by observing the evolution of the plots and tracking the relevant features.