RPRuslan Popov

Ruslan Popov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ruslan Popov has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    30 mm Wide IBAD-MgO REBCO Coated Conductors Developed at the KC 4 Facility

    by Sukanya Baruah, Ruslan Popov, Jens Hänisch, Vladimir Matias, Nadezda Bagrets, Rainer Nast, Shraddha Singhal, Jan Korvink, Christian Barth, Amalia Ballarino, et al.

    In this paper we report on a novel HTS coated conductor developed at the KIT-CERN Collaboration on Coated Conductors (KC4) facility at the Institute of Technical Physics (ITEP), Karlsruhe Institute of Technology (KIT), Germany, namely the first-ever 30 mm wide coated conductor on IBAD-MgO, which was provided by iBeam Materials. These samples are highly homogenous with self-field Jc values at 77 K and 30 K of 1.0 MA/cm2 and 6.6 MA/cm2 respectively. We will briefly introduce the KC4 facility, which is a pilot production coated conductor R&D laboratory, established for material development to bridge the gap between research and manufacturing and to transfer small-scale PLD research results to large-scale coated conductors (CCs). Since the completion of the deposition line in 2023, REBCO films have been deposited on long-length metal substrates with various buffer stacks, and reasonably good Ic values of 300 A/cm width at 77 K on 12 mm wide tapes were obtained with the potential for further improvement. Efforts are in progress to upscale the R&D to wider tapes that will open new avenues for the application of CCs in the high-field, low temperature region as well as for special applications.

  • Oxygen Annealing of GdBa2Cu3O7−$\delta$ Superconducting Thin Films: Influence of Annealing Time

    by Ruslan Popov, Jens Hänisch, Bernhard Holzapfel

    GdBa 2 Cu 3 O 7-δ (GdBCO) superconducting thin films, grown by Pulsed Laser Deposition (PLD) on MgO(100) single crystals are oxygen annealed using two different approaches: in-situ (oxygen annealing in PLD chamber) and ex-situ (oxygen annealing in tubular furnace). Their structural and transport properties are investigated in relation to annealing time (t ann ) at 450°. In-situ annealed GdBCO thin films require at least 15 min of annealing to achieve high in-field critical current densities (J c ), while ex-situ annealed samples achieve high in-field J c already after 5 min of oxygen annealing at 450° and 1 bar of oxygen pressure.


  • Open Access

    Effect of oxygenation process on flux pinning in pristine and BaHfO3 nanocomposite GdBa2Cu3O7 superconducting thin films

    by Ruslan Popov, Kai Ackermann, H. Rijckaert, Jens Hänisch, I. Van Driessche, Bernhard Holzapfel

    Pristine and BaHfO3 (BHO) nanocomposite GdBa2Cu3O7 (GdBCO) superconducting thin films were deposited at 800 °C, 0.4 mbar O2 partial pressure using a Nd:YAG laser (λ=355 nm) with 10 Hz frequency on MgO substrate. The influence of the oxygenation process on flux pinning and electrical transport properties was investigated by changing the annealing temperature (T ann) between 450 °C and 780 °C and the holding time (t hold) between 10 and 30 min. The irreversibility field shows the largest shift toward higher fields for T ann = 450 °C and thus the largest in-field J c. Angular dependence of J c for most of the pristine GdBCO films exhibits a large peak for B‖c, however the sample with T ann = 550 °C has a large peak in the 90°-120° region, i.e. near B ‖ ab. For BHO nanocomposites, a decrease in T ann increases in-field J c by a factor of 2.