AIAyman Ismail
Ayman Ismail
*This is an algorithmically generated author record based on publicly available information.
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ayman Ismail has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Ahmad F. Allam
ECE Department, Faculty of Engineering, Ain Shams University, Cairo 11535, Egypt
1 shared publication Ahmed Elshennawy
Si-Ware Systems,Cairo,Egypt
1 shared publication- Ahmed Hamed
Department of Mathematics, Faculty of Sciences, Monastir, Tunisia
1 shared publication Alaa Safwat
MEMS Vision LLC,Cairo,Egypt
1 shared publication- Ali Badawy1 shared publication
- Hesham Omran
Integrated Circuits Laboratory (ICL), Faculty of Engineering, Ain Shams University, Cairo 11517, Egypt
1 shared publication
Latest Publications
- Open Access
- 30 March 2025
- Published by MDPI AG in Electronics
- Vol. 14 (7) , 1386
A Noise-Shaping SAR-Based Capacitance-to-Digital Converter for Sensing Applications
In this work, an energy-efficient noise-shaping (NS) successive-approximation (SAR) capacitance-to-digital converter (CDC) is proposed. The interface is based on a direct-comparison technique, in which the sensor capacitance is compared directly to an on-chip binary weighted capacitive digital-to-analog converter (DAC). To implement NS, a 2nd order feed-forward loop filter processes the extracted residue at the end of each conversion cycle. Employing NS to achieve the target resolution leads to a small capacitive DAC and hence a small Si-area compared to the conventional SAR approach that would require a capacitive DAC with the same resolution as the overall CDC resolution. The proposed capacitive NS SAR sensor interface is designed and implemented in 130 nm CMOS technology for a 4 pF dynamic range and achieves an effective number of bits (ENOB) of 12.0 bits with a measurement time of 2.5 ms. The CDC dissipates 1.0 A from a 0.8 V supply resulting in a figure of merit (FoM) of 488 fJ/conversion-step.- 30 March 2025
- Published by MDPI AG in Electronics
- Vol. 14 (7) , 1386
Open AccessA Noise-Shaping SAR-Based Capacitance-to-Digital Converter for Sensing Applications
In this work, an energy-efficient noise-shaping (NS) successive-approximation (SAR) capacitance-to-digital converter (CDC) is proposed. The interface is based on a direct-comparison technique, in which the sensor capacitance is compared directly to an on-chip binary weighted capacitive digital-to-analog converter (DAC). To implement NS, a 2nd order feed-forward loop filter processes the extracted residue at the end of each conversion cycle. Employing NS to achieve the target resolution leads to a small capacitive DAC and hence a small Si-area compared to the conventional SAR approach that would require a capacitive DAC with the same resolution as the overall CDC resolution. The proposed capacitive NS SAR sensor interface is designed and implemented in 130 nm CMOS technology for a 4 pF dynamic range and achieves an effective number of bits (ENOB) of 12.0 bits with a measurement time of 2.5 ms. The CDC dissipates 1.0 A from a 0.8 V supply resulting in a figure of merit (FoM) of 488 fJ/conversion-step. - Open Access
- 20 October 2024
- Published by MDPI AG in Electronics
- Vol. 13 (20) , 4128
On the System-Level Design of Noise-Shaping SAR Analog-to-Digital Converters
In this work, the system-level design of noise-shaping (NS) successive-approximation (SAR) analog-to-digital converters (ADCs) is investigated and analyzed. It is shown that despite the fact that the NS SAR architecture shares the same fundamental NS principle with the architecture, there are a few implementation differences that imply different considerations for optimum system-level design, particularly in the selection of the system oversampling ratio (OSR) and consequent resolution of the associated digital-to-analog converter (DAC) for a certain target overall resolution. In addition, the impacts of the OSR value on the power dissipation and figure-of-merit (FOM) are addressed in details.- 20 October 2024
- Published by MDPI AG in Electronics
- Vol. 13 (20) , 4128
Open AccessOn the System-Level Design of Noise-Shaping SAR Analog-to-Digital Converters
In this work, the system-level design of noise-shaping (NS) successive-approximation (SAR) analog-to-digital converters (ADCs) is investigated and analyzed. It is shown that despite the fact that the NS SAR architecture shares the same fundamental NS principle with the architecture, there are a few implementation differences that imply different considerations for optimum system-level design, particularly in the selection of the system oversampling ratio (OSR) and consequent resolution of the associated digital-to-analog converter (DAC) for a certain target overall resolution. In addition, the impacts of the OSR value on the power dissipation and figure-of-merit (FOM) are addressed in details. - Open Access
- 23 April 2024
- Published by MDPI AG in Electronics
- Vol. 13 (9) , 1602
Graphical Design Approach for UWB Stacked CG LNA Using Inversion Coefficient
The design of ultra-wide-band (UWB) low-noise amplifiers (LNAs) entails a large number of design challenges and tradeoffs, which include sustaining good input matching over a wide bandwidth along with finding a proper compromise between various LNA performance metrics, such as gain, bandwidth, noise figure, power, and linearity. This paper presents a design approach for UWB LNAs based on the inversion coefficient (IC). The proposed approach is a graphical design approach where the proper operating point is chosen based on predefined constraints. A complete systematic solution is presented for the problem of UWB input matching with a high degree of analytical accuracy. The design approach is illustrated through the design of two UWB stacked common-gate LNAs in 65 nm technology. The post-layout simulation results show very good agreement with analytical expectations. The first LNA achieves an better than −8.2 dB over a 27.6 GHz frequency range, a gain of 12.4 dB over a 16.5 GHz bandwidth, a minimum noise-figure, NF, of 4.5 dB, and an of −5.2 dBm while consuming only 530 W. The second LNA achieves an better than −15 dB over an 8.8 GHz frequency range, a gain of 12.5 dB over a 6.8 GHz bandwidth, a minimum NF of 4 dB, and an of −4.3 dBm while consuming only 550 W.- 23 April 2024
- Published by MDPI AG in Electronics
- Vol. 13 (9) , 1602
Open AccessGraphical Design Approach for UWB Stacked CG LNA Using Inversion Coefficient
The design of ultra-wide-band (UWB) low-noise amplifiers (LNAs) entails a large number of design challenges and tradeoffs, which include sustaining good input matching over a wide bandwidth along with finding a proper compromise between various LNA performance metrics, such as gain, bandwidth, noise figure, power, and linearity. This paper presents a design approach for UWB LNAs based on the inversion coefficient (IC). The proposed approach is a graphical design approach where the proper operating point is chosen based on predefined constraints. A complete systematic solution is presented for the problem of UWB input matching with a high degree of analytical accuracy. The design approach is illustrated through the design of two UWB stacked common-gate LNAs in 65 nm technology. The post-layout simulation results show very good agreement with analytical expectations. The first LNA achieves an better than −8.2 dB over a 27.6 GHz frequency range, a gain of 12.4 dB over a 16.5 GHz bandwidth, a minimum noise-figure, NF, of 4.5 dB, and an of −5.2 dBm while consuming only 530 W. The second LNA achieves an better than −15 dB over an 8.8 GHz frequency range, a gain of 12.5 dB over a 6.8 GHz bandwidth, a minimum NF of 4 dB, and an of −4.3 dBm while consuming only 550 W. - 5 January 2024
- Published by Elsevier in Microelectronics Journal
- Vol. 144
Inverter-based noise-shaping SAR ADC for low-power applications
- 5 January 2024
- Published by Elsevier in Microelectronics Journal
- Vol. 144
Inverter-based noise-shaping SAR ADC for low-power applications
- 1 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
A General Purpose Single-Slope MEMS Capacitive Sensors Interface Circuit For IoT Applications
A new energy-efficient single-slope capacitance-to-digital interface circuit is proposed. The proposed interface circuit is a general purpose interface that can be adapted for multi-sensors IoT applications. This interface utilizes a new iterative charge sharing technique, which can be easily configures for different capacitive sensor ranges. The interface employs a switched capacitor circuit followed by a low-power dynamic comparator and a digital controller with a counter to generate the digital output, corresponding to the input capacitance of the sensor. The simplicity of the proposed capacitance-to-digital converter (CDC) architecture leads to an energy efficient interface. Detailed analysis of the proposed CDC architecture with emphasis on the linearity, conversion time, and noise are presented and verified by the simulation. The proposed CDC achieves a resolution of 8.4 bit and a figure-of-merit (FoM) of 1.56pJ for a capacitor sensor range of 8pF and a supply voltage of 1.2V in $0.18\mu \mathrm{m}$ CMOS technology node.- 1 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
A General Purpose Single-Slope MEMS Capacitive Sensors Interface Circuit For IoT Applications
A new energy-efficient single-slope capacitance-to-digital interface circuit is proposed. The proposed interface circuit is a general purpose interface that can be adapted for multi-sensors IoT applications. This interface utilizes a new iterative charge sharing technique, which can be easily configures for different capacitive sensor ranges. The interface employs a switched capacitor circuit followed by a low-power dynamic comparator and a digital controller with a counter to generate the digital output, corresponding to the input capacitance of the sensor. The simplicity of the proposed capacitance-to-digital converter (CDC) architecture leads to an energy efficient interface. Detailed analysis of the proposed CDC architecture with emphasis on the linearity, conversion time, and noise are presented and verified by the simulation. The proposed CDC achieves a resolution of 8.4 bit and a figure-of-merit (FoM) of 1.56pJ for a capacitor sensor range of 8pF and a supply voltage of 1.2V in $0.18\mu \mathrm{m}$ CMOS technology node.- 1 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 5-8
A Design Method for $\Delta\sum$ Force-Feedback Accelerometer Interface SystemsDelta-Sigma $(\Delta\Sigma)$ technique represents an optimum way for realizing force-feedback electromechanical systems, especially for capacitive sensors. However, when operating the sensor in feedback, the stability of the system becomes a concern, particularly, in $\Delta\Sigma$ -based systems, and the higher the order of the system, the harder it becomes to achieve stability. Hence, following a systematic design flow for these systems is essential. While the design of stable electrical $\Delta\Sigma$ loops is well established, the design of electromechanical $\Delta\Sigma$ loops presents a challenge due to the nature of the capacitive sensor resonator. In this work, a way to stabilize high-order $\Delta\Sigma$ -based interface systems for inertial capacitive sensors is introduced and a systematic design approach is proposed. The design approach is based on noise transfer function (NTF) matching which translates the system design problem to an NTF design problem as in electrical $\Delta\Sigma$ loops. The design approach is applied to the design of a fifth-order $\Delta\Sigma$ based interface for a capacitive accelerometer. The sensor has a $0.12 \ \mu \mathrm{g}$ proof-mass, a resonance frequency of 1.8 kHz, a displacement-to-capacitance factor of $3.22 \ \text{pF}/ \mu \mathrm{m}$ and a feedback factor of $0.7 \ \mu \mathrm{N/V}^{2}$ . The designed system achieves a signal-to-quantization noise ratio (SQNR) of 181 dB.- 1 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 5-8
A Design Method for $\Delta\sum$ Force-Feedback Accelerometer Interface SystemsDelta-Sigma $(\Delta\Sigma)$ technique represents an optimum way for realizing force-feedback electromechanical systems, especially for capacitive sensors. However, when operating the sensor in feedback, the stability of the system becomes a concern, particularly, in $\Delta\Sigma$ -based systems, and the higher the order of the system, the harder it becomes to achieve stability. Hence, following a systematic design flow for these systems is essential. While the design of stable electrical $\Delta\Sigma$ loops is well established, the design of electromechanical $\Delta\Sigma$ loops presents a challenge due to the nature of the capacitive sensor resonator. In this work, a way to stabilize high-order $\Delta\Sigma$ -based interface systems for inertial capacitive sensors is introduced and a systematic design approach is proposed. The design approach is based on noise transfer function (NTF) matching which translates the system design problem to an NTF design problem as in electrical $\Delta\Sigma$ loops. The design approach is applied to the design of a fifth-order $\Delta\Sigma$ based interface for a capacitive accelerometer. The sensor has a $0.12 \ \mu \mathrm{g}$ proof-mass, a resonance frequency of 1.8 kHz, a displacement-to-capacitance factor of $3.22 \ \text{pF}/ \mu \mathrm{m}$ and a feedback factor of $0.7 \ \mu \mathrm{N/V}^{2}$ . The designed system achieves a signal-to-quantization noise ratio (SQNR) of 181 dB.