Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Wei Feng has a total of 28 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    The Effect of Temperature and Physical State of Water on the Frictional Properties of Chlorite‐Altered Basaltic Gouges (Krafla Geothermal Field, Iceland)

    by W.‐H. Wu, W. Feng, R. Gomila, T. Tesei, A. K. Mortensen, G. Di Toro

    Changes in the physical state of water may alter fault frictional properties in high‐temperature geothermal systems, yet they have been little studied. Here, we perform slide‐hold‐slide experiments to examine the frictional properties (frictional strength μ ss and frictional healing Δ μ ) of chlorite‐altered basalt from Krafla Geothermal Field under realistic hydrothermal conditions (temperature of 100–400°C and pore pressure of 3–30 MPa with water in liquid, vapor, and supercritical states). We show that (a) μ ss is slightly larger in vapor ( μ ss ∼ 0.67–0.73) than in liquid and supercritical water ( μ ss ∼ 0.61–0.64); (b) Δ μ increases with both the logarithm of contact hold time and temperature; (c) stick‐slip occurs at ≥300°C, and the stress drops are largest in vapor water. In the sheared gouges, slip zones are characterized by grain‐size reduction of plagioclase and quartz due to cataclasis (≤300°C) and dissolution (400°C) without evidence of newly‐formed minerals. The temperature‐dependent Δ μ of gouges in the presence of liquid and supercritical water is promoted by the rearrangement of size‐reduced grains and grain dissolution, while the large Δ μ in vapor water may result from the formation of interfacial chemical bonds between grains. Our results agree with the seismological observations in Krafla, where shallow faults cutting chlorite‐altered basalts at temperatures <200°C accommodate deformation mostly by aseismic slip (creep), while deeper faults are seismogenic at ≥300°C and in the presence of boiling fluids.


  • Open Access

    Semi-brittle deformation of Solnhofen limestone: Initial porosity effects on strength

    by Wei Feng, Nicolas Brantut

    Semi-brittle deformation, characterized by the concurrent operation of cataclasis and crystal plasticity, plays a key role in constraining the strength of the middle crust. While the effects of temperature, pressure, fluid-abundance/pressure, and material properties (e.g., grain size) have been relatively well studied, the role of initial porosity in semi-brittle deformation remains poorly understood. Here, we performed a series of triaxial compression experiments on dry samples of Solnhofen limestone, which has an initial porosity of ~5.6% and an isotropic texture. Experiments were conducted at a range of confining pressures (Pc=30-300 MPa), temperatures (T=25 to 600 °C) and a constant strain rate of 1×10-5 s-1. Under these conditions, Solnhofen limestone mainly deforms in the semi-brittle regime associated with strain hardening, and brittle fracturing only occurs at low pressures (Pc≤50 MPa) and T

  • Open Access

    Frictional weakening of gabbro faults after quasi-stationary contact under hydrothermal conditions

    by Wei Feng, Lu Yao, Shengli Ma, Feng Shi, Jinyu Zheng, Giulio Di Toro

  • Open Access

    Feldspar reduces fault frictional healing rate under hydrothermal conditions

    by Wei Feng, Wenzhou Wang, Lu Yao, Rodrigo Gomila, Shengli Ma, Qunyang Li, Giulio Di Toro

    Fault restrengthening after earthquakes enables country rocks to restore elastic strain energy for subsequent seismic cycles. It originates from the contribution of several processes resulting in fault sealing and fault frictional healing, the latter arising from contact area growth and formation of new chemical bonds between grains. Laboratory studies demonstrate that fault frictional healing typically increases logarithmically with time during quasi-stationary contact (i.e., positive healing rate). Here we show that this logarithmic healing does not hold under certain (hydrothermal) conditions for feldspar, the most abundant mineral in the Earth’s crust, and for common feldspar-rich rocks. The healing rate switches from positive to negative with increasing quasi-stationary contact time at temperatures ≥ 200 °C in the presence of pressurized water. This unusual healing behavior suggests that thermally-activated friction weakening processes may exist at feldspar interfaces. This hypothesis is further validated through nano-scale friction experiments by sliding single-feldspar crystals on a feldspar substrate. Given the abundance of feldspars in the Earth’s crust, their peculiar healing behavior under hydrothermal conditions can lead to unexpected variations in fault strength, changing our understanding of fault mechanics and the seismic cycle, and challenging the direct extrapolation of laboratory-derived healing parameters to natural earthquake recurrence intervals.


  • Open Access

    Seismic fault slip at depths simulated by high-velocity friction experiments under hydrothermal conditions

    by Lu Yao, Wei Feng, Chiara Cornelio, Toshihiko Shimamoto, Shengli Ma, Giulio Di Toro

    Seismic fault slip and rupture propagation often occur at crustal depths in the presence of hot and pressurized aqueous fluids (i.e., hydrothermal conditions). Previous experiments investigated fault frictional properties under hydrothermal conditions, but at imposed subseismic fault slip velocities ( V ~μm/s). Here, using a rotary-shear apparatus equipped with a hydrothermal pressure vessel, we study friction at seismic slip velocities ( V = 1.5 m/s) of gabbro- and marble-built faults under temperatures of 40 to 400 °C and pore water pressure of 30 MPa. We find that with increasing initial water temperature ( T amb ), the dynamic friction during initial slip acceleration and subsequent high-velocity sliding decreases for both gabbro- and marble-built faults, while the slip-weakening distance decreases for gabbro but increases for marble. Then, during rapid deceleration at the end of sliding, frictional strength recovery decreases for gabbro with increasing T amb and increases for marble independently of T amb . As in previous experiments performed at room T amb , the mechanical and microstructural data, plus numerical modeling, suggest that the seismic fault weakening mechanisms shift from flash heating to bulk melting for gabbro, and from flash heating to grain boundary sliding accommodated by diffusion creep for marble, with their activation processes depending on T amb . Our results demonstrate the effects of ambient temperature on seismic fault friction, which contribute to changes in fault strength and dynamic weakening processes at crustal depths and should be considered in earthquake rupture modeling.


  • Open Access

    Frictional behavior of chlorite in large-displacement experiments under hydrothermal conditions

    by Weifeng Qin, Lu Yao, Tongbin Shao, Wei Feng, Jianye Chen, Shengli Ma

    The frictional properties of faults are primarily controlled by their mineral composition, as well as ambient and deformation conditions, such as temperature, pore fluid, normal stress, and slip displacement. While many studies have been conducted to decipher how temperature and pore fluid may affect the frictional behavior of faults, less attention has been paid to the slip displacement effects, especially under hydrothermal conditions. By employing a rotary shear apparatus equipped with an externally-heated hydrothermal pressure vessel, we conducted large-displacement (up to 521 mm) friction experiments on chlorite under temperature (T) of 25 to 400℃ and pore water pressure (Pp) of 30MPa. The imposed effective normal stresses were 200 MPa and the slip rates ranged from 0.4 to 10 μm/s. The experiments unveiled significant slip strengthening in chlorite within the temperature range of 25 to 400 °C. Moreover, with increasing temperatures, there was an overall increasing trend in both the rate of slip strengthening and the ultimate frictional strength. For example, under T = 25 °C, the friction coefficients at displacements of 5, 90, and 521 mm were 0.33, 0.49, and 0.59, respectively, in contrast to 0.46, 0.79, and 0.88, respectively, at the same three displacements under T =400 °C. Under all the temperature and displacement conditions, chlorite exhibited velocity strengthening behavior without discernible temperature dependence, although the velocity-dependence parameter (a-b) increased with slip displacement. Microstructural analysis revealed that, the entire layer of the chlorite gouge experienced pervasive and intense shear deformation after slip of 521 mm, with extremely remarkable grain-size reduction. The thermogravimetrical and FTIR data of the deformed chlorite samples, together with the microstructural data, suggest that the dehydroxylation and the distortion of crystal structure of chlorite might occur during the friction experiments conducted at T ≥ 200 °C. Such changes may explain the more pronounced slip strengthening of chlorite with increasing temperatures towards 400 °C. This explanation can be further demonstrated by a comparative experiment conducted under varying temperatures (400°C for the first 100 mm of slip, followed by 25°C for the rest of 100 mm slip), wherein the friction coefficient at T = 25°C during the latter stage of slip remains as high as that at T = 400°C. These findings highlight the importance of slip displacement in controlling the frictional strength and its variations of chlorite-bearing faults at depths, and have profound implications for understanding the fault slip behaviors and earthquake mechanisms in subduction zones.

  • Open Access

    Temperature and Physical State of Water Controls Frictional Healing of Basaltic Gouges from Krafla (Iceland)

    by Wei-Hsin Wu, Wei Feng, Rodrigo Gomila, Telemaco Tesei, Marie Violay, Anette K. Mortensen, Giulio Di Toro

    Fault’s frictional strength and particularly its ability to heal during the interseismic period (fault frictional healing Δμ) is critical to understand the seismic cycle, yet the understanding of temperature and phase-dependent healing characteristics of natural geothermal conditions remains limited. Here we examined the frictional healing of both simulated fresh and chlorite-altered basaltic gouge from Krafla geothermal field (Iceland) under realistic geothermal conditions of water temperature Tf = 100-400 ˚C and pressure Pf = 10-30 MPa (water in liquid, vapor and supercritical state) by performing Slide-Hold-Slide (SHS) experiments. All experiments were performed under a constant effective normal stress of 10 MPa and initiated with a 5-mm run-in slip at a loading point slip rate V of 10 mm/s before the SHS sequence. For each SHS sequence, shearing was held from 3 s to 10,000 s, separated by a slip interval of 1mm. Our mechanical results indicate that frictional healing, the difference between peak friction reached upon re-shear and the steady-state friction before the hold, increases with increasing logarithm of hold time in all experiments, as suggested by previous studies. Meanwhile, frictional healing rate (β = Δμ/log(1+ thold/tcutoff)), commonly regarded as the quantification of the rate of healing, increases with increasing temperature for both fresh and altered basalt. For fresh basalt, β increases from 0.007 at Tf = 100 ˚C to 0.060 at Tf = 300 ˚C (liquid) before dropping to 0.036 at Tf = 400 ˚C (vapor) and eventually increases to 0.096 at Tf = 400 ˚C (supercritical). For altered basalt, β increases continuously from 0.003-0.007 at Tf = 100 ˚C to 0.013-0.022 at Tf = 300 ˚C and reaches its maximum value of β = 0.024-0.035 at Tf = 400 ˚C (vapor) and β = 0.030 at Tf = 400 ˚C (supercritical). Besides this temperature-dependent relationship, the dramatic decrease of β in fresh basalt to values similar to those of altered basalt when water changed from liquid to vapor state also suggests that the physical state of water can control the healing rate. Subsequent microanalytical analyses (XRPD, XRF, SEM-EDS) performed on the deformed gouges from altered basalts suggest an increase in hydrothermal alteration with increasing temperature, as shown by a depletion in K2O at Tf ≥ 300 ˚C. SEM-BSE images of fine platy matrices in shear bands formed at Tf = 400 ˚C point towards a dissolution of quartz, pyroxene and plagioclase. Therefore, we suggest that the healing rate of both fresh and altered basalt not only scales with the ambient temperature but is also affected by the physical state of water, particularly in the case of fresh basalt, potentially related to more intense fluid-rock interactions with increasing temperature.Keywords: frictional healing, frictional healing rate, hydrothermal fluids, basaltic gouge, Krafla geothermal field

  • Open Access

    Slip‐Dependence of Fault Frictional Stability Under Hydrothermal Conditions

    by Wei Feng, Lu Yao, Rodrigo Gomila, Shengli Ma, Giorgio Pennacchioni, Giulio Di Toro

    In the rate‐state friction law framework, the transition from velocity weakening ( V‐W ) to velocity strengthening ( V‐S ) behavior marks the base of the seismogenic crust. Here we investigate the role of fault slip displacement under hydrothermal conditions in controlling the V‐W to V‐S transition. We shear simulated gabbro gouges at slip velocities ranging from 16 nm/s (∼50 cm/year) to 10 μm/s (∼8 cm/day) under hydrothermal conditions (300–400°C temperature; 30 MPa pore fluid pressure). We observe that cumulative fault slip increases the critical velocity for the V‐W to V‐S transition. The transition is accompanied by localized to distributed deformation mode, the formation of smectite‐type clays and occurrence of intergranular mass transfer. Our results provide insights into understanding the deepening and shallowing of V‐W / V‐S boundary (lower limit of the seismogenic zone) following a mainshock. Besides strain rate effects, slip‐enhanced chemical alteration and grain size‐sensitive deformation may temporarily contribute to the shallowing process.


  • Open Access

    Recent Advances in Reservoir Stimulation and Enhanced Oil Recovery Technology in Unconventional Reservoirs

    by Lufeng Zhang, Linhua Pan, Yushi Zou, Jie Wang, Minghui Li, Wei Feng

    In the past decade, significant advances in reservoir stimulation and enhanced oil recovery technologies have resulted in rapid production growth in unconventional reservoirs