MLMin-Jeong Lee

Min-Jeong Lee

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Min-Jeong Lee has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Preparation of Flake-shape Cobalt Powders by High-Energy Ball Milling for rSOC Current Collectors

    by Poong-Yeon Kim, Min-Jeong Lee, Hyeon Ju Kim, Su-Jin Yun, Si Young Chang, Jung-Yeul Yun

    Reversible solid oxide cells (rSOCs), which enable two-way conversion between electricity and hydrogen, have gained attention with the rise of hydrogen energy. However, foam-type current collectors in rSOC stacks exhibit poor structural controllability and limited electrode contact area. To address these limitations, this study aimed to convert spherical cobalt powders into flake-type morphology via high-energy ball milling, as a preliminary step toward fabricating flake-based current collectors.Milling parameters—specifically, the ball-to-powder ratio (BPR), milling time, and process control agent (PCA) content—were varied. At an 8:1 BPR, over 90% of the powder became flake-shaped after 8 hours, while extended milling caused cold welding. In contrast, a 10:1 BPR resulted in dominant fragmentation. The Burgio–Rojac model quantified energy input and defined the optimal range for flake formation. Increasing the PCA to 4 wt% delayed flake formation to 16 hours and induced cold welding, as shown by bimodal particle size distributions. These results support the development of Co-based current collectors for use in rSOCs.

  • Fabricating Metal Powder Filters with Material Extrusion Additive Manufacturing

    by Min-Ji Kim, Min-Jeong Lee, Hyun-Ju Kim, Ju-Yong Kim, Jung-Woo Lee, Jung-Yeul Yun

    Metal powder filters are key components in semiconductor manufacturing equipment that play a critical role in preventing the ingress of impurities and fine particles that may be contained in process gases. With the increasingly advanced development of the semiconductor industry, metal powder filters also require more precise and advanced performance. Therefore, in this study, a filter with a honeycomb structure morphology with crossed top and bottom was fabricated by a material extrusion additive manufacturing (MEAM) process. To achieve this, the prepared pellets were subjected to the MEAM, allowing the creation of filters with complex shapes featuring crossed top and bottom structures. After polishing the surface of the specimen, solvent debinding and thermal debinding were performed to remove the binder. Solvent debinding was performed in n-Heptane for 24 hours, while thermal debinding was performed in an Ar atmosphere at a maximum temperature of 800°C. The debinded specimens were sintered under a high vacuum atmosphere at temperatures of 850°C, 950°C, and 1050°C, respectively. The prepared metal powder filters were examined for filter morphology and microstructure using optical microscopy, and pore properties such as porosity and air permeability were evaluated.

  • Open Access

    Fabrication and Pore Characteristics of Metal Powder Filters with a Cross-Sealed Honeycomb Shape Using Material Extrusion Additive Manufacturing

    by Minji Kim, Min-Jeong Lee, Su-Jin Yun, Poong-Yeon Kim, Hyeon Ju Kim, Juyong Kim, Jung Woo Lee, Jung-Yeul Yun

    The development of high-performance metal filters is essential for maintaining ultra-clean environments in semiconductor manufacturing. In this study, cross-sealed honeycomb filters were fabricated using STS316L powder via material extrusion additive manufacturing (MEAM) for semiconductor gas filtration. The effects of filter geometry (4 or 9 channels) and sintering temperature (850°C, 950°C, or 1,050°C) on performance were examined. First, 4-channel and 9-channel filters sintered at the same temperature (950°C) exhibited similar porosities of 50.08% and 50.57%, but the 9-channel filter showed a higher pressure-drop (0.26 bar) and better filtration-efficiency (3.55 LRV) than the 4-channel filter (0.19 bar and 3.25 LRV, respectively). Second, for filters with the same geometry (4-channel) increasing the sintering temperature reduced porosity from 64.52% to 40.33%, while the pressure-drop increased from 0.13 bar to 0.22 bar and filtration-efficiency improved from 2.53 LRV to 3.51 LRV. These findings demonstrate that filter geometry and sintering temperature are key factors governing the trade-off between air permeability, pressure-drop, and filtration efficiency. This work provides insights and data for optimizing MEAM-based high-performance metal powder filter design.

  • The Effect of the Size of SUS316L Flake Powder on the Characteristics of Metal Powder Filt ers with a Double-Layered Pore Structure Fabricated by the WPS Process

    by Min-Jeong Lee, Hyeon-Ju Kim, Manho Park, Jungwoo Lee, Jung-Yeul Yun

    When fabricating a metal powder filter with a double-layered pore structure, which includes a microporous layer, by coating flake-shaped powder using the Wet Powder Spray (WPS) process, it is crucial to ensure that the coating is applied parallel to the surface of the metal powder filter. Failure to do so can result in a non-uniform pore structure, leading to a rapid decline in particle filtration efficiency. Therefore, it is necessary to improve the alignment of the coated flake-shaped powder on the filter surface. In this study, a metal powder filter with a double-layered pore structure was fabricated by applying a flake-shaped metal powder coating to a tube-shaped SUS316L powder filter using the WPS process. In order to improve the flake-shaped powder orientation of coating layer, the impact of the rolling process was investigated. The characteristics of the pores were analyzed based on the powder size and the rolling time. The microstructure of the fabricated metal powder filter was observed using an optical microscope, surface roughness, variations in thickness, and air permeability were analysed.


  • Fabrication of Metal Gas Filter by Material Extrusion Additive Manufacturing Process

    by Yu-Jeong Yi, Min-Jeong Lee, Su-Jin Yun, Manho Park, Ju-Yong Kim, Jungwoo Lee, Jung-Yeul Yun

    Recently, 3D printing processes have been used to manufacture metal powder filters with manufacturing complex-shape. In this study, metal powder filters of various shapes were manufactured using the metal extrusion additive manufacturing (MEAM) process, which is used to manufacture three-dimensional structures by extruding a filament consisting of a metal powder and a binder. Firstly, filaments were prepared by appropriately mixing SUS316 powder with sizes ranging from 7.5 µm to 50 µm and a binder. These filaments were extruded at temperatures of 100℃ to 160℃ depending on the type of filament being manufactured, to form three types of cylindrical filter. Specimens were sintered in a high vacuum atmosphere furnace at 850℃ to 1050℃ for 1 hour after debinding. The specimens were analyzed for permeability using a capillary flow porometer, porosity was determined by applying Archimedes’ law and microstructure was observed using SEM.


  • Fabrication and Pore Properties of SUS316L Membrane with Double-Layered Pore Structures by Wet Powder Spraying

    by Min-Jeong Lee, Hyeon-Ju Kim, Manho Park, Jung-Yeul Yun

    In this study, a SUS316L membrane having double layered pore structures was fabricated, and the pore characteristics were analyzed after coating with a spherical powder and a flake-shaped powder on a disk-shaped SUS316L support using a wet powder spraying process. The thickness of the coated layer was checked using an optical microscope, and air permeability was measured using a capillary flow porometer. When the coating amount was similar, the fine porous layer prepared using flake powder was thicker and showed higher porosity. In the case of a similar thickness, the case of using flake powder was half of the amount of spherical powder used. Therefore, it was confirmed that it is possible to manufacture a metal membrane having a high filter efficiency even with a small coating amount when using the flake powder.


  • Microstructure and Pore Characteristics of a SUS316L Gas Filter Fabricated by Wet Powder Spraying

    by Min-Jeong Lee, Yu-Jeong Yi, Hyeon-Ju Kim, Manho Park, Jungwoo Lee, Jung-Yeul Yun

    In this study, a flake-shaped metal powder was coated on a tube shaped pre-sintered 316L stainless steel support using a wet powder spraying process to fabricate a double pore structure, and the pore characteristics were analyzed according to coating time and tube rotation speed. The thickness of the coated layer was checked via optical microscopy, and porosity was measured using image analysis software. Air permeability was measured using a capillary flow porometer. As a result of the experiment, the optimal rotation speed of the support tube was established as 200 rpm. When the rotation speed was fixed, the coating thickness and the coating amount of the double pore structure increased as the coating time increased. The porosity of the double pore structure was increased due to the irregular arrangement of the flake-shaped powder. The air permeability of the double pore structure decreased with increasing fine pore layer thickness.