St.M. Dobosz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
St.M. Dobosz has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- A. Grabarczyk
AGH University of Science and Technology, Faculty of Foundry Engineering, Department of Moulding Materials, Mould Technology and Foundry of Non-ferrous Metals, Al. Mickiewicza 30, 30-059 Krakow, Poland
2 shared publications - Jarosław Jakubski
AGH University of Krakow
2 shared publications - Katarzyna Major-Gabryś
AGH University of Krakow, Faculty of Foundry Engineering, Department of Moulding Materials, Mould Technology and Non-ferrous Metals, al. A. Mickiewicza 30, 30-059 Krakow, Poland
2 shared publications - Dana Bolibruchová
Department of technological engineering, Faculty of Mechanical Engineering, University of Žilina, Univerzitná 8215/1, 010 26 Žilina, Slovakia
1 shared publication - Richard Pastirčák
Department of technological engineering, Faculty of Mechanical Engineering, University of Žilina, Univerzitná 8215/1, 010 26 Žilina, Slovakia
1 shared publication
Latest Publications
- Open Access
- 15 September 2023
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 68 (3) , 933-937
Tests of Mechanical and Thermal Deformation of Moulding Sands Produced in Various Technologies
Casting industry has been enriched with the processes of mechanization and automation in production. They offer both better working standards, faster and more accurate production, but also have begun to generate new opportunities for new foundry defects. This work discusses the disadvantages of processes that can occur, to a limited extend, in the technologies associated with mould assembly and during the initial stages of pouring. These defects will be described in detail in the further part of the paper and are mainly related to the quality of foundry cores, therefore the discussion of these issues will mainly concern core moulding sands. Four different types of moulding mixtures were used in the research, representing the most popular chemically bonded moulding sands used in foundry practise. The main focus of this article is the analysis of the influence of the binder type on mechanical and thermal deformation in moulding sands.
- 15 September 2023
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 68 (3) , 933-937
Open AccessTests of Mechanical and Thermal Deformation of Moulding Sands Produced in Various Technologies
Casting industry has been enriched with the processes of mechanization and automation in production. They offer both better working standards, faster and more accurate production, but also have begun to generate new opportunities for new foundry defects. This work discusses the disadvantages of processes that can occur, to a limited extend, in the technologies associated with mould assembly and during the initial stages of pouring. These defects will be described in detail in the further part of the paper and are mainly related to the quality of foundry cores, therefore the discussion of these issues will mainly concern core moulding sands. Four different types of moulding mixtures were used in the research, representing the most popular chemically bonded moulding sands used in foundry practise. The main focus of this article is the analysis of the influence of the binder type on mechanical and thermal deformation in moulding sands.
- Open Access
- 1 June 2015
- Published by Walter de Gruyter GmbH in Archives of Foundry Engineering
- Vol. 15 (2) , 9-12
Influence of Quartz Sand Quality on Bending Strength and Thermal Deformation of Moulding Sands with Synthetic Binders
Modern techniques of castings production, including moulding sands production, require a strict technological regime and high quality materials. In the case of self-hardening moulding sands with synthetic binders those requirements apply mainly to sand, which adds to more than 98% of the whole moulding sand mixture. The factors that affect the quality of the moulding sands are both chemical (SiO2, Fe2O3 and carbonates content) and physical. Among these factors somewhat less attention is paid to the granulometric composition of the sands. As a part of this study, the effect of sand quality on bending strength Rgu and thermal deformation of self-hardening moulding sands with furfural and alkyd resin was assessed. Moulding sands with furfural resin are known [1] to be the most susceptible to the sand quality. A negative effect on its properties has, among others, high content of clay binder and so-called subgrains (fraction smaller than 0,1mm), which can lead to neutralization of acidic hardeners (in the case of moulding sands with furfuryl resin) and also increase the specific surface, what forces greater amount of binding agents. The research used 5 different quartz sands originating from different sources and characterized with different grain composition and different clay binder content.
- 1 June 2015
- Published by Walter de Gruyter GmbH in Archives of Foundry Engineering
- Vol. 15 (2) , 9-12
Open AccessInfluence of Quartz Sand Quality on Bending Strength and Thermal Deformation of Moulding Sands with Synthetic Binders
Modern techniques of castings production, including moulding sands production, require a strict technological regime and high quality materials. In the case of self-hardening moulding sands with synthetic binders those requirements apply mainly to sand, which adds to more than 98% of the whole moulding sand mixture. The factors that affect the quality of the moulding sands are both chemical (SiO2, Fe2O3 and carbonates content) and physical. Among these factors somewhat less attention is paid to the granulometric composition of the sands. As a part of this study, the effect of sand quality on bending strength Rgu and thermal deformation of self-hardening moulding sands with furfural and alkyd resin was assessed. Moulding sands with furfural resin are known [1] to be the most susceptible to the sand quality. A negative effect on its properties has, among others, high content of clay binder and so-called subgrains (fraction smaller than 0,1mm), which can lead to neutralization of acidic hardeners (in the case of moulding sands with furfuryl resin) and also increase the specific surface, what forces greater amount of binding agents. The research used 5 different quartz sands originating from different sources and characterized with different grain composition and different clay binder content.