Dinesh Dhanabalan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dinesh Dhanabalan has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- A. Megalingam
Department of Mechanical Engineering, Bannari Amman Institute of Technology, Sathyamangalam, India
1 shared publication - Nandana Raghuraj
Bannari Amman Institute of Technology
1 shared publication - Pavithra Kathiresan
Bannari Amman Institute of Technology
1 shared publication - Prakashraj Muthaiya
Bannari Amman Institute of Technology
1 shared publication - Rajasekar Rathanasamy
Mechanical Engineering , 121733 Kongu Engineering College , Erode , Tamil Nadu , India
1 shared publication - Thirumurugan Jeyakumar
Bannari Amman Institute of Technology
1 shared publication
Latest Publications
- 14 August 2024
- Published by Kaunas University of Technology (KTU) in Materials Science
- Vol. 30 (3) , 334-339
Experimental Investigation of Date seed and Neem Powder Reinforced Natural Fiber Composites
Natural fillers have received great attention among researchers due their its light weight, high strength, degradability, and eco-friendly behavior. This work is focused on developing a laminate of date palm seed powder and neem gum powder reinforced epoxy resin. Epoxy resin is an excellent thermoset polymer with anoutstanding cost to performance ratio. Date palm seeds have highly competitive properties in improving the mechanical and thermal properties of composites by their good adherence to polymer matrix. Neem gum powder is used as a binder in increasing ratios of 0 %, 10 %, 15 %, 20 %, 25 %, and 30 % to test their strength in different compositions. Date seed powder has been reinforced in decreasing weight percent as 30 %, 25 %, 20 %, 15 %, 10 %, 5 %, and 0 %. The specimens prepared through the compression moulding technique were subjected to various mechanical tests like a tensile test, flexural test, and impact test as per the ASTM standards. Fractography analysis using FESEM (Field Emission Scanning Electron Microscopy) and FT-IR(Fourier Transform Infrared spectroscopy) test have determined the surface characteristics and chemical composition of the samples. The result shows that, by adding neem gum powder in increasing quantities the mechanical properties like tensile and flexural decreases. However, it does not affect the impact strength of the material. A detailed study of their behavior is discussed in this work.
- 14 August 2024
- Published by Kaunas University of Technology (KTU) in Materials Science
- Vol. 30 (3) , 334-339
Experimental Investigation of Date seed and Neem Powder Reinforced Natural Fiber Composites
Natural fillers have received great attention among researchers due their its light weight, high strength, degradability, and eco-friendly behavior. This work is focused on developing a laminate of date palm seed powder and neem gum powder reinforced epoxy resin. Epoxy resin is an excellent thermoset polymer with anoutstanding cost to performance ratio. Date palm seeds have highly competitive properties in improving the mechanical and thermal properties of composites by their good adherence to polymer matrix. Neem gum powder is used as a binder in increasing ratios of 0 %, 10 %, 15 %, 20 %, 25 %, and 30 % to test their strength in different compositions. Date seed powder has been reinforced in decreasing weight percent as 30 %, 25 %, 20 %, 15 %, 10 %, 5 %, and 0 %. The specimens prepared through the compression moulding technique were subjected to various mechanical tests like a tensile test, flexural test, and impact test as per the ASTM standards. Fractography analysis using FESEM (Field Emission Scanning Electron Microscopy) and FT-IR(Fourier Transform Infrared spectroscopy) test have determined the surface characteristics and chemical composition of the samples. The result shows that, by adding neem gum powder in increasing quantities the mechanical properties like tensile and flexural decreases. However, it does not affect the impact strength of the material. A detailed study of their behavior is discussed in this work.
- 28 December 2021
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 66 (4) , 1095-1104
Dry Sliding Friction and Wear Behaviour of Leaded Tin bronze for Bearing and Bushing Application
Among different bearing materials, copper-based alloys are the most important source for bearing and bushing applications. In this work, the tribological behavior of a leaded tin bronze (Cu-22Pb-4Sn) against an EN31 Steel for various loads (20 N, 70 N, 120 N) and different sliding velocity (1 m/s, 3 m/s, 5 m/s) at 3000 m sliding distance is performed using a pin on disk tribometer. Irrespective of all loads and sliding velocity, a higher specific wear rate is observed at 1 m/s and 120 N that fails to facilitate the formation of lubricating film, whereas a lower specific wear rate is evident when the sliding velocity is increased to 5 m/s. This is attributed to the formation of a stable oxide layer that has been confirmed through the Energy dispersive X-ray spectroscopy analysis and Scanning electron microscopy. The coefficient of friction is observed in reducing trend from 0.69 to 0.48 for the increasing load (70 N, 120 N) and sliding velocity (3 m/s and 5 m/s) due to stable thin oxide film formation. Also, the increase in frictional force and loading the interacting surface temperature is increased to a maximum of 102°C. The Grey relational analysis indicates that the optimal parameters for the minimum specific wear rate and coefficient of friction is 120 N and 5 m/s that has been confirmed with experimental analysis.
- 28 December 2021
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 66 (4) , 1095-1104
Dry Sliding Friction and Wear Behaviour of Leaded Tin bronze for Bearing and Bushing Application
Among different bearing materials, copper-based alloys are the most important source for bearing and bushing applications. In this work, the tribological behavior of a leaded tin bronze (Cu-22Pb-4Sn) against an EN31 Steel for various loads (20 N, 70 N, 120 N) and different sliding velocity (1 m/s, 3 m/s, 5 m/s) at 3000 m sliding distance is performed using a pin on disk tribometer. Irrespective of all loads and sliding velocity, a higher specific wear rate is observed at 1 m/s and 120 N that fails to facilitate the formation of lubricating film, whereas a lower specific wear rate is evident when the sliding velocity is increased to 5 m/s. This is attributed to the formation of a stable oxide layer that has been confirmed through the Energy dispersive X-ray spectroscopy analysis and Scanning electron microscopy. The coefficient of friction is observed in reducing trend from 0.69 to 0.48 for the increasing load (70 N, 120 N) and sliding velocity (3 m/s and 5 m/s) due to stable thin oxide film formation. Also, the increase in frictional force and loading the interacting surface temperature is increased to a maximum of 102°C. The Grey relational analysis indicates that the optimal parameters for the minimum specific wear rate and coefficient of friction is 120 N and 5 m/s that has been confirmed with experimental analysis.