Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Laura Moreno-Corrales has a total of 7 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Relación Micro-Macro en Leyes de Daño en Sólidos No-Lineales

    by Laura Moreno Corrales

    Fracture Mechanics is a branch within the area of Continuum Mechanics that focuses on the study of how defects form and propagate within a continuous solid until they cause its structural failure. The first studies related to the damage or failure mechanisms of materials in Fracture Mechanics date back to about the XVth-XVIth centuries where engineers such as Leonardo da Vinci and Galileo Galilei, among others, showed in some of their studies interest in how to characterize the fracture observed experimentally in materials, which caused a change in the mechanical properties of the same. However, it was in the middle of the XXth century when the first studies by Kachanov and Rabotnov appear on how to model damage in a material using an internal variable, in this case a scalar variable. The purpose of this variable was to characterize the progressive deterioration in the mechanical properties of the material up to the moment of fracture with respect to the properties of the undamaged material. This Thesis studies how to identify and model the effect caused by damage on the effective mechanical properties of several materials: 1) composite material, 2) metamaterial and 3) hyperelastic material. The three materials under study present a very different internal structure. However, they all show similar quantitative mechanical behaviour in the face of damage (pores, cracks, creep, etc.). For this reason, using the concepts of Fracture Mechanics and the Thermodynamics of Irreversible Processes, it is possible to simulate with relative success the damage behaviour of materials as diverse as those studied in this work, modelling this behaviour through mechanical variables without making detailed reference to the complexity of the respective physical structures that constitute each of them. In relation to the damage of a composite material, this work has studied the matrix failure or inter-fibre failure that appears in composite laminates when they are subjected to tensile loads in the transverse direction to the fiber. For this purpose, the bond between the matrix and the fibre, called adhesive or interface, has been modelled as if it were a continuous distribution of springs. This bond region is characterised by significant instabilities that are difficult to reproduce with the mathematical methods used in commercial Finite Element Method programs. For this reason, it is proposed to use a linear sequential resolution algorithm that allows to reproduce these instabilities with a good approximation. With regard to the damage of a metamaterial, it is experimentally observed that at a micromechanical level there is currently little similarity between the models designed on the computer and the printed samples obtained using additive manufacturing techniques as 3D printing. This is due to the fact that computer-designed models do not have the capacity to reproduce the defects that appears, in the printed models. For this reason, this work presents how different defects observed experimentally in the printed materials have been modelled, such as porosity, nodal deviation, which have been introduced in the undamaged model by means of a mathematical algorithm, obtaining computationally models whose effective mechanical properties are closer to those obtained in the printed models. With respect to the damage of a hyperelastic material, it is experimentally observed that some hyperelastic materials, such as polymers, elastomers, among others, present an energy dissipation known as the Mullins Effect or softening of the material. This effect is difficult to quantify for various reasons such as; 1) the material has the capacity to reproduce different unloading-reloading curves associated with viscosity, 2) permanent residual deformations appear, 3) anisotropy in the damage. In this work, a model has been proposed to characterize the behavior of hyperelastic materials based on the internal energy and entropy. RESUMEN La Mecánica de la Fractura es una rama dentro del área de la Mecánica de los Medios Continuos que se centra en el estudio de cómo se forman y se propagan los defectos en el interior un sólido continuo hasta provocar el fallo estructural del mismo. Los primeros estudios relacionados con el daño o los mecanismos de fallo de los materiales en la Mecánica de Fractura datan de aproximadamente los siglos XV-XVI donde ingenieros como, Leonardo da Vinci y Galileo Galilei, entre otros, mostraron en algunos de sus estudios interés en cómo caracterizar la fractura observada experimentalmente en los materiales, la cuál provocaba una modificación en las propiedades mecánicas de los mismos. Sin embargo, es a mediados del siglo XX cuando aparecen los primeros estudios de Kachanov y Rabotnov acerca de cómo modelar el daño en un material utilizando una variable interna en este caso escalar. Dicha variable tenía como objetivo caracterizar el deterioro progresivo en las propiedades mecánicas del material hasta el momento de la fractura. En esta tesis se realiza el estudio de cómo identificar y modelar el efecto que causa el daño en las propiedades mecánicas efectivas de varios materiales: 1) material compuesto, 2) metamaterial y 3) material hiperelástico. Los tres materiales bajo estudio presentan una estructura interna diferente, sin embargo, todos manifiestan frente al daño un comportamiento mecánico cuantitativo similar. Por este motivo, utilizando conceptos de la Mecánica de Fractura y de la Termodinámica de Procesos Irreversibles se puede intentar simular con relativo éxito el comportamiento al daño de materiales tan diversos como los estudiados en este trabajo. En relación al daño de un material compuesto, en este trabajo se ha estudiado el fallo de matriz que aparece en los laminados de materiales compuestos cuando están sometidos a cargas de tracción en...

  • Open Access

    Using the Mooney Space to Characterize the Non-Affine Behavior of Elastomers

    by Laura Moreno-Corrales, Miguel Ángel Sanz-Gómez, José María Benítez, Luis Saucedo-Mora, Francisco J. Montáns

    The formulation of the entropic statistical theory and the related neo-Hookean model has been a major advance in the modeling of rubber-like materials, but the failure to explain some experimental observations such as the slope in Mooney plots resulted in hundreds of micromechanical and phenomenological models. The origin of the difficulties, the reason for the apparent need for the second invariant, and the reason for the relative success of models based on the Valanis–Landel decomposition have been recently explained. From that insight, a new micro–macro chain stretch connection using the stretch tensor (instead of the right Cauchy–Green deformation tensor) has been proposed and supported both theoretically and from experimental data. A simple three-parameter model using this connection has been suggested. The purpose of this work is to provide further insight into the model, to provide an analytical expression for the Gaussian contribution, and to provide a simple procedure to obtain the parameters from a tensile test using the Mooney space or the Mooney–Rivlin constants. From different papers, a wide variety of experimental tests on different materials and loading conditions have been selected to demonstrate that the simple model calibrated only from a tensile test provides accurate predictions for a wide variety of elastomers under different deformation levels and multiaxial patterns.


  • Open Access

    Incorporation of Defects in Finite Elements to Model Effective Mechanical Properties of Metamaterial Cells Printed by Selective Laser Melting

    by Gonzalo Vera-Rodríguez, Laura Moreno-Corrales, Iván Marín-González, Daniel Barba, Francisco J. Montáns, Miguel Ángel Sanz-Gómez

    Additively printed mechanical metamaterial structures optimize material, energy and waste, producing more sustainable products. Their introduction in the production workflow depends on having proper tools for accurately predicting their performance. However, the additive manufacturing process incorporates significant defects which result in an important change of the effective properties of the metamaterial cell. Finite element predictions using perfect geometries and nominal base material properties result in important errors which may require excessive uncertainty-related safety design margins. This work presents a methodology to introduce the effect of the most common defects in finite element models to compute the effective mechanical response of different metamaterials printed by Selective Laser Melting. It is shown that even at elastic infinitesimal strains, the defects produce an important change in the effective mechanical capabilities of the metamaterial, which also depend on the type of the metamaterial cell studied and on the type and magnitude of defects. With the proposed methodology, which incorporates the distribution of defects in the finite element model, the predicted mechanical properties of the metamaterial better match the experimental ones. It is shown that the initial discrepancies in the order of 100% are reduced to an order of 5%.