Indri Dayana
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Indri Dayana has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Habib Satria
Universitas Medan Area
8 shared publications - Syafii Syafii
Universitas Andalas
4 shared publications - Dadan Ramdan
Universitas Medan Area
3 shared publications - Dina Maizana
Universitas Medan Area
3 shared publications - Muhammad Fadlan Siregar
Universitas Medan Area
2 shared publications - Muhammad Irwanto
Universitas Prima Indonesia
2 shared publications
Latest Publications
- Open Access
- 1 September 2026
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 17 (3) , 2162-2171
Comparison of acrylic and zinc blade materials on the performance of Darrieus vertical axis wind turbine
The performance of vertical axis wind turbine is strongly influenced by blade characteristics, yet the effect of blade material on turbine performance remains relatively underexplored, particularly for small scale Darrieus type turbines. This study experimentally investigated the influence of acrylic and zinc blade materials on the aerodynamics and energy conversion performance of a three bladed Darrieus vertical axis wind Turbine. A laboratory-scale experimental setup was employed to evaluated turbine rotational speed, torque, and electrical power under a controlled wind speed of 4.3 m/s. The results demonstrate the blade material significantly affects the turbine’s ability to extract and convert wind energy. The acrylic blade turbine achieved a power coefficient (Cp) of 0.293 and an overall conversion efficiency 62.81%, compared with 0.208 and 47.11%, respectively, for the zinc bladed turbine. The acrylic configuration therefore provided approximately 25% higher overall performance than zinc configuration. These findings experimentally validate the importance of blade material selection in the design of small scale Darrieus wind turbines and indicate that acrylic can provide a more effective alternative to zinc for improving wind energy conversion under low speed operating conditions. The results provide practical guidance for material selection in the development of lightweight, low speed vertical axis turbines for decentralized and small scale renewable energy applications.
- 1 September 2026
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 17 (3) , 2162-2171
Open AccessComparison of acrylic and zinc blade materials on the performance of Darrieus vertical axis wind turbine
The performance of vertical axis wind turbine is strongly influenced by blade characteristics, yet the effect of blade material on turbine performance remains relatively underexplored, particularly for small scale Darrieus type turbines. This study experimentally investigated the influence of acrylic and zinc blade materials on the aerodynamics and energy conversion performance of a three bladed Darrieus vertical axis wind Turbine. A laboratory-scale experimental setup was employed to evaluated turbine rotational speed, torque, and electrical power under a controlled wind speed of 4.3 m/s. The results demonstrate the blade material significantly affects the turbine’s ability to extract and convert wind energy. The acrylic blade turbine achieved a power coefficient (Cp) of 0.293 and an overall conversion efficiency 62.81%, compared with 0.208 and 47.11%, respectively, for the zinc bladed turbine. The acrylic configuration therefore provided approximately 25% higher overall performance than zinc configuration. These findings experimentally validate the importance of blade material selection in the design of small scale Darrieus wind turbines and indicate that acrylic can provide a more effective alternative to zinc for improving wind energy conversion under low speed operating conditions. The results provide practical guidance for material selection in the development of lightweight, low speed vertical axis turbines for decentralized and small scale renewable energy applications.
- Open Access
- 1 July 2026
- Published by Institute of Advanced Engineering and Science in International Journal of Reconfigurable and Embedded Systems (IJRES)
- Vol. 15 (2)
Machine learning for energy conversion prediction and photovoltaic-on grid protection system using IoT
The advancement of photovoltaic (PV) systems in tropical regions faces significant efficiency challenges due to fluctuating panel surface temperatures. This study addresses these issues by implementing machine learning (ML) models, specifically k-nearest neighbors (KNN) and extreme gradient boosting (XGBoost), to classify and monitor panel temperatures. To enhance system resilience, an internet of things (IoT) based on-grid protection system was developed, featuring a dual-relay redundancy mechanism that triggers an automated trip when the current exceeds 1.30 A. This integration ensures the protection of both the PV infrastructure and household electrical loads. Experimental results demonstrate that the KNN model exhibits superior reliability with a testing accuracy of 93% and a baseline performance of 96.67%, successfully identifying both normal (25 °C to 35 °C) and high-temperature (36 °C to 48 °C) states. In contrast, while the XGBoost model reached a maximum validation accuracy of 94.44% during training, it only achieved a testing accuracy of 84% and showed significant limitations in detecting normal temperature patterns. Beyond classification, the IoT framework proved highly precise in real-time energy monitoring, with sensor error rates below 2%. This research offers a strategic solution for optimizing energy conversion and system reliability, providing a robust framework for sustainable clean energy management in tropical climates.
- 1 July 2026
- Published by Institute of Advanced Engineering and Science in International Journal of Reconfigurable and Embedded Systems (IJRES)
- Vol. 15 (2)
Open AccessMachine learning for energy conversion prediction and photovoltaic-on grid protection system using IoT
The advancement of photovoltaic (PV) systems in tropical regions faces significant efficiency challenges due to fluctuating panel surface temperatures. This study addresses these issues by implementing machine learning (ML) models, specifically k-nearest neighbors (KNN) and extreme gradient boosting (XGBoost), to classify and monitor panel temperatures. To enhance system resilience, an internet of things (IoT) based on-grid protection system was developed, featuring a dual-relay redundancy mechanism that triggers an automated trip when the current exceeds 1.30 A. This integration ensures the protection of both the PV infrastructure and household electrical loads. Experimental results demonstrate that the KNN model exhibits superior reliability with a testing accuracy of 93% and a baseline performance of 96.67%, successfully identifying both normal (25 °C to 35 °C) and high-temperature (36 °C to 48 °C) states. In contrast, while the XGBoost model reached a maximum validation accuracy of 94.44% during training, it only achieved a testing accuracy of 84% and showed significant limitations in detecting normal temperature patterns. Beyond classification, the IoT framework proved highly precise in real-time energy monitoring, with sensor error rates below 2%. This research offers a strategic solution for optimizing energy conversion and system reliability, providing a robust framework for sustainable clean energy management in tropical climates.
- Open Access
- 1 June 2026
- Published by Institute of Advanced Engineering and Science in International Journal of Advances in Applied Sciences
- Vol. 15 (2) , 622-633
Multi-level redundancy with internet of things battery supply for fault mitigation in grid-tied photovoltaic systems
The development of grid-tied photovoltaic (PV) systems in tropical regions remains a strategic focus for achieving sustainable clean energy. However, energy conversion efficiency is often hampered by fluctuations in panel surface temperature and electrical faults. To ensure long-term system reliability, this study implements a multi-level redundancy architecture integrated with dynamic internet of things (IoT) monitoring for fault mitigation in grid-tied PV systems. The system employs a machine learning (ML) method using the k-nearest neighbors (KNN) algorithm for thermal classification, achieving an accuracy of 84% in identifying normal (25 °C to 35 °C) and overheating conditions. Furthermore, an electrical redundancy layer is designed with an automatic tripping mechanism that activates when the current exceeds a 1.30 A threshold, demonstrating a rapid response latency of 150 ms. To ensure monitoring resilience, the system is supported by a dedicated 18650 Li-ion battery backup. The implementation results confirm that this multi-level protection framework effectively monitors real time energy usage, prevents critical component damage, and enhances the overall safety of household-scale PV installations. This research provides a scalable and intelligent solution for fault mitigation, supporting the broader adoption of renewable energy in tropical environments.
- 1 June 2026
- Published by Institute of Advanced Engineering and Science in International Journal of Advances in Applied Sciences
- Vol. 15 (2) , 622-633
Open AccessMulti-level redundancy with internet of things battery supply for fault mitigation in grid-tied photovoltaic systems
The development of grid-tied photovoltaic (PV) systems in tropical regions remains a strategic focus for achieving sustainable clean energy. However, energy conversion efficiency is often hampered by fluctuations in panel surface temperature and electrical faults. To ensure long-term system reliability, this study implements a multi-level redundancy architecture integrated with dynamic internet of things (IoT) monitoring for fault mitigation in grid-tied PV systems. The system employs a machine learning (ML) method using the k-nearest neighbors (KNN) algorithm for thermal classification, achieving an accuracy of 84% in identifying normal (25 °C to 35 °C) and overheating conditions. Furthermore, an electrical redundancy layer is designed with an automatic tripping mechanism that activates when the current exceeds a 1.30 A threshold, demonstrating a rapid response latency of 150 ms. To ensure monitoring resilience, the system is supported by a dedicated 18650 Li-ion battery backup. The implementation results confirm that this multi-level protection framework effectively monitors real time energy usage, prevents critical component damage, and enhances the overall safety of household-scale PV installations. This research provides a scalable and intelligent solution for fault mitigation, supporting the broader adoption of renewable energy in tropical environments.
- Open Access
- 2 May 2025
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 14 (3) , 1656-1666
Optimization of parabolic photovoltaic and solar thermal tracker model systems using heat transfer fluid
Renewable energy sources such as photovoltaic (PV) and solar thermal (T) used in tropical Indonesia are still not optimal in converting electrical energy. This is caused by the movement of the sun which is not centered on the surface of the photovoltaic/thermal (PV/T). Based on this, PV/T technology was developed with a parabolic tracker system combined with T control with the aim of optimizing electrical energy conversion. The testing technique was carried out using an experimental method by comparing the installation of PV/T technology with a parabolic tracker system and a flat PV position. In the PV/T parabolic tracker, the supporting components use aluminum foil technology and heat transfer fluid (HTF) to reduce excess heat on the panel surface. The parabolic tracker system is implemented through a centralized system following the sun and aluminum foil and HTF technology function to keep the surface temperature stable. The results of PV performance testing at peak loads carried out at 10:00 am-3:00 pm, the installation of flat PV produced an average DC power of 71.68 Wp and the parabolic tracker system produced an increase in average DC power of 84.57 Wp, while with an increase in power of 17.98% during fluctuating weather conditions.
- 2 May 2025
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 14 (3) , 1656-1666
Open AccessOptimization of parabolic photovoltaic and solar thermal tracker model systems using heat transfer fluid
Renewable energy sources such as photovoltaic (PV) and solar thermal (T) used in tropical Indonesia are still not optimal in converting electrical energy. This is caused by the movement of the sun which is not centered on the surface of the photovoltaic/thermal (PV/T). Based on this, PV/T technology was developed with a parabolic tracker system combined with T control with the aim of optimizing electrical energy conversion. The testing technique was carried out using an experimental method by comparing the installation of PV/T technology with a parabolic tracker system and a flat PV position. In the PV/T parabolic tracker, the supporting components use aluminum foil technology and heat transfer fluid (HTF) to reduce excess heat on the panel surface. The parabolic tracker system is implemented through a centralized system following the sun and aluminum foil and HTF technology function to keep the surface temperature stable. The results of PV performance testing at peak loads carried out at 10:00 am-3:00 pm, the installation of flat PV produced an average DC power of 71.68 Wp and the parabolic tracker system produced an increase in average DC power of 84.57 Wp, while with an increase in power of 17.98% during fluctuating weather conditions.
- Open Access
- 1 July 2024
- Published by Institute of Advanced Engineering and Science in International Journal of Reconfigurable and Embedded Systems (IJRES)
- Vol. 13 (2) , 315-322
Earthquake detection in mountainous homes using the internet of things connected to photovoltaic energy supply
The North Sumatra region is an area with the potential for earthquakes originating from volcanic and oceanic eruptions which have resulted in many fatalities. Therefore, through the application of automatic monitoring and control system technology connected to the internet of things (IoTs), it is the right solution to provide efforts to increase security for residents of the house to always be vigilant. The security enhancement method referred to in this study is a home security system protection system by anticipating earthquakes. The advantage of this tool is that it applies a notification security system method with a sensitivity sensor which is automatically sent via email and sonor buzzer which also acts as sound vibrations due to an earthquake. The test results show that when a vibration occurs, the system will send a short email message to the user's smartphone so that the user will receive an email in the form of a warning message that the state of the house has an earthquake and the light-emitting diode (LED) interrupts and the buzzer is also on so that the alarm sounds which has been integrated into IoT. Then an integrated security monitoring system using the web can be monitored in real time.
- 1 July 2024
- Published by Institute of Advanced Engineering and Science in International Journal of Reconfigurable and Embedded Systems (IJRES)
- Vol. 13 (2) , 315-322
Open AccessEarthquake detection in mountainous homes using the internet of things connected to photovoltaic energy supply
The North Sumatra region is an area with the potential for earthquakes originating from volcanic and oceanic eruptions which have resulted in many fatalities. Therefore, through the application of automatic monitoring and control system technology connected to the internet of things (IoTs), it is the right solution to provide efforts to increase security for residents of the house to always be vigilant. The security enhancement method referred to in this study is a home security system protection system by anticipating earthquakes. The advantage of this tool is that it applies a notification security system method with a sensitivity sensor which is automatically sent via email and sonor buzzer which also acts as sound vibrations due to an earthquake. The test results show that when a vibration occurs, the system will send a short email message to the user's smartphone so that the user will receive an email in the form of a warning message that the state of the house has an earthquake and the light-emitting diode (LED) interrupts and the buzzer is also on so that the alarm sounds which has been integrated into IoT. Then an integrated security monitoring system using the web can be monitored in real time.
- Open Access
- 1 February 2024
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 14 (1) , 66-74
Development of energy conversion and lightning strike protection simulation for photovoltaic-wind turbine on grid
Photovoltaic (PV) installations and wind turbines that are installed on the rooftops of buildings need to be protected because the layout is in a high position and there is a risk of being struck by lightning. Therefore, a more effective protection system is designed to anticipate electronic damage and fire on all materials in the distribution network, especially the addition of PV and wind turbine installations on building roofs. The purpose of this study is to simulate a lightning protection system on the distribution network and the results of on-grid PV energy conversion using electrical transient analyzer program (ETAP) software. Feeder relay delay times and cascade coordination patterns between outgoing and incoming relays do not overlap. the delay time of the relay working on the feeder is 0.31 s and the coordination pattern of the outgoing relay and incoming relay does not touch each other, so the delay time for the incoming relay is 2.73 s. Then testing the results of PV energy conversion connected to the grid using MATLAB Simulink monitoring obtained data reaching 1.600 Wp at peak power with sun conditions parallel to the PV installation layout.
- 1 February 2024
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 14 (1) , 66-74
Open AccessDevelopment of energy conversion and lightning strike protection simulation for photovoltaic-wind turbine on grid
Photovoltaic (PV) installations and wind turbines that are installed on the rooftops of buildings need to be protected because the layout is in a high position and there is a risk of being struck by lightning. Therefore, a more effective protection system is designed to anticipate electronic damage and fire on all materials in the distribution network, especially the addition of PV and wind turbine installations on building roofs. The purpose of this study is to simulate a lightning protection system on the distribution network and the results of on-grid PV energy conversion using electrical transient analyzer program (ETAP) software. Feeder relay delay times and cascade coordination patterns between outgoing and incoming relays do not overlap. the delay time of the relay working on the feeder is 0.31 s and the coordination pattern of the outgoing relay and incoming relay does not touch each other, so the delay time for the incoming relay is 2.73 s. Then testing the results of PV energy conversion connected to the grid using MATLAB Simulink monitoring obtained data reaching 1.600 Wp at peak power with sun conditions parallel to the PV installation layout.
- Open Access
- 3 August 2023
- Published by Institute of Postgraduate Studies, Syiah Kuala University in Aceh International Journal of Science and Technology
- Vol. 12 (2) , 276-284
Simple Technology of Material Physics of Groundwater Conservation in Dealing with Climate Change in Disaster Areas of North Sumatra
Water is a natural resource with a very important function for human life and advancing general welfare, so water is the basic capital and the main development factor. After the eruption in the Mount Sinabung area, the supply of healthy water was inadequate both in quantity and quality, even though the Karo Regency government made efforts to provide this healthy water. For this reason, appropriate technology is needed in post-eruption water treatment in Mount Sinabung to become healthy water and be used by the local community. This research aims to provide information about Groundwater Conservation Technology in Facing Climate Change in the Disaster Areas of North Sumatra. The method used is quantitative with a purposive sampling technique by selecting 6 wells from 348 wells around Mount Sinabung. Chemical parameters for sampling each - each 1 liter of water to be put in bottles previously cleaned and rinsed with distilled water first, then dried. Laboratory Tests then examined them. There is a simple technology in the form of a water filter made from a mixture of sand, activated carbon, and dried starfruit leaves, which can neutralize contamination of substances such as sulfur and others in the water to obtain healthy water suitable for people in the disaster area.
- 3 August 2023
- Published by Institute of Postgraduate Studies, Syiah Kuala University in Aceh International Journal of Science and Technology
- Vol. 12 (2) , 276-284
Open AccessSimple Technology of Material Physics of Groundwater Conservation in Dealing with Climate Change in Disaster Areas of North Sumatra
Water is a natural resource with a very important function for human life and advancing general welfare, so water is the basic capital and the main development factor. After the eruption in the Mount Sinabung area, the supply of healthy water was inadequate both in quantity and quality, even though the Karo Regency government made efforts to provide this healthy water. For this reason, appropriate technology is needed in post-eruption water treatment in Mount Sinabung to become healthy water and be used by the local community. This research aims to provide information about Groundwater Conservation Technology in Facing Climate Change in the Disaster Areas of North Sumatra. The method used is quantitative with a purposive sampling technique by selecting 6 wells from 348 wells around Mount Sinabung. Chemical parameters for sampling each - each 1 liter of water to be put in bottles previously cleaned and rinsed with distilled water first, then dried. Laboratory Tests then examined them. There is a simple technology in the form of a water filter made from a mixture of sand, activated carbon, and dried starfruit leaves, which can neutralize contamination of substances such as sulfur and others in the water to obtain healthy water suitable for people in the disaster area.
- Open Access
- 1 March 2023
- Published by Innovative Research Publication in International Journal of Innovative Research in Computer Science and Technology
- Vol. 11 (2) , 34-37
The Initial Process of Dam Construction is Seen from a Topographical Perspective (Bench Mark Coordinates and Control Point Coordinates): Case study of D.I. Bajayu Kab Serdang Bedagai
- 1 March 2023
- Published by Innovative Research Publication in International Journal of Innovative Research in Computer Science and Technology
- Vol. 11 (2) , 34-37
Open AccessThe Initial Process of Dam Construction is Seen from a Topographical Perspective (Bench Mark Coordinates and Control Point Coordinates): Case study of D.I. Bajayu Kab Serdang Bedagai