Yanuar Prabowo
Research Subjects
Yanuar Prabowo has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Cahya Edi Santosa
National Research and Innovation Agency (BRIN)
2 shared publications - Imas Tri Setyadewi
National Research and Innovation Agency (BRIN)
2 shared publications - Abdurrasyid Ruhiyat
Department of Electrical Engineering, Universitas Indonesia, Depok 16424, Indonesia
1 shared publication - Agus Hendra Wahyudi
National Research and Innovation Agency (BRIN)
1 shared publication Cahya Edi Santosa
Badan Riset dan Inovasi Nasional (BRIN)
1 shared publicationDonatina Miswati Hadiyanti
Badan Riset dan Inovasi Nasional (BRIN)
1 shared publication
Latest Publications
- Open Access
- 1 August 2025
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 14 (4) , 2649-2661
Analysis of unmanned aerial vehicle airframe materials on circularly polarized antenna radiation characteristics
This paper presents an experimental examination of how unmanned aerial vehicle (UAV) airframe materials affect the electromagnetic characteristics of the airborne circularly polarized (CP) payload antenna. This study specifically investigates the received signal from the circularly polarized synthetic aperture radar (CP-SAR) antenna installed within the fuselage of the lapan surveillance UAV (LSU). In the airborne CP-SAR experiment, broadband CP microstrip subarray antennas were used along with LSU series airframe material composites comprising E-glass EW-185 and Carbon C522 Twill. The composite specimens were prepared to have the same size and thickness to minimize variability in the comparative analysis. The experimental study measures the transmission loss using S-parameters. At 5.3 GHz, the E-glass EW-185 fiber composite exhibits a material attenuation of -1.5 dB and a circular depolarization of 0.32 dB. The E-glass EW-185 fiber composite exhibits a material attenuation of -1.5 dB and a circular depolarization of 0.32 dB. In contrast, the Carbon C522 Twill fiber composite demonstrates a significantly higher material attenuation of -31.24 dB and a circular depolarization of 10.70 dB. Additionally, this paper examines the radiation pattern measurements of the CP-SAR antenna at various frequencies, providing a comprehensive analysis of the materials' impact on antenna performance.
- 1 August 2025
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 14 (4) , 2649-2661
Open AccessAnalysis of unmanned aerial vehicle airframe materials on circularly polarized antenna radiation characteristics
This paper presents an experimental examination of how unmanned aerial vehicle (UAV) airframe materials affect the electromagnetic characteristics of the airborne circularly polarized (CP) payload antenna. This study specifically investigates the received signal from the circularly polarized synthetic aperture radar (CP-SAR) antenna installed within the fuselage of the lapan surveillance UAV (LSU). In the airborne CP-SAR experiment, broadband CP microstrip subarray antennas were used along with LSU series airframe material composites comprising E-glass EW-185 and Carbon C522 Twill. The composite specimens were prepared to have the same size and thickness to minimize variability in the comparative analysis. The experimental study measures the transmission loss using S-parameters. At 5.3 GHz, the E-glass EW-185 fiber composite exhibits a material attenuation of -1.5 dB and a circular depolarization of 0.32 dB. The E-glass EW-185 fiber composite exhibits a material attenuation of -1.5 dB and a circular depolarization of 0.32 dB. In contrast, the Carbon C522 Twill fiber composite demonstrates a significantly higher material attenuation of -31.24 dB and a circular depolarization of 10.70 dB. Additionally, this paper examines the radiation pattern measurements of the CP-SAR antenna at various frequencies, providing a comprehensive analysis of the materials' impact on antenna performance.
- Open Access
- 30 June 2025
- Published by Universitas Negeri Semarang in Jurnal Teknik Elektro
- Vol. 17 (1) , 1-6
Analysis and Characterization of Shielding Material for Mitigating Electromagnetic Interference in UAVs
This study aims to mitigate the impact of electromagnetic interference on the performance of electronic systems in Unmanned Aerial Vehicles (UAVs) by employing various shielding materials. The materials tested include carbon fiber, E-glass, E-glass with an aluminium foil, and E-glass with a copper foil. A Vector Network Analyzer (VNA) and scattering parameter (S-Parameter) analysis, including reflection, absorption, and multiple reflection, were used to evaluate the shielding effectiveness of these materials within the frequency range of 4 - 5 GHz. The results showed that E-glass coated with copper had good overall shielding performance for SER, SEA, and SET values. This material reached a SET value of 96 dB at a frequency of 4.6 GHz, followed by E-glass coated with aluminium. In addition, adding carbon layers increased the shielding effectiveness, while E-glass without coating had the lowest shielding performance compared to the other materials. These findings indicate that E-glass coated with metal provides superior shielding effectiveness compared to carbon fiber, even when used in greater thickness.
- 30 June 2025
- Published by Universitas Negeri Semarang in Jurnal Teknik Elektro
- Vol. 17 (1) , 1-6
Open AccessAnalysis and Characterization of Shielding Material for Mitigating Electromagnetic Interference in UAVs
This study aims to mitigate the impact of electromagnetic interference on the performance of electronic systems in Unmanned Aerial Vehicles (UAVs) by employing various shielding materials. The materials tested include carbon fiber, E-glass, E-glass with an aluminium foil, and E-glass with a copper foil. A Vector Network Analyzer (VNA) and scattering parameter (S-Parameter) analysis, including reflection, absorption, and multiple reflection, were used to evaluate the shielding effectiveness of these materials within the frequency range of 4 - 5 GHz. The results showed that E-glass coated with copper had good overall shielding performance for SER, SEA, and SET values. This material reached a SET value of 96 dB at a frequency of 4.6 GHz, followed by E-glass coated with aluminium. In addition, adding carbon layers increased the shielding effectiveness, while E-glass without coating had the lowest shielding performance compared to the other materials. These findings indicate that E-glass coated with metal provides superior shielding effectiveness compared to carbon fiber, even when used in greater thickness.
- Open Access
- 1 February 2024
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 14 (1) , 22-30
Unconsidered but influencing interference in unmanned aerial vehicle cabling system
The increasing complexity of electrical and electronic systems in unmanned aerial vehicles (UAVs) has raised concerns regarding unwanted electromagnetic interference (EMI) due to limited compartment space. Recent studies have highlighted the UAV cabling as the primary pathway for interference. This paper presents a novel approach to investigating the effects of interference power, polarization angle, and distance from the interference source on EMI in UAV cable systems. Measurements and simulations were performed to analyze the influence of these factors on the radiation received by the cable. A linear dipole antenna, operating at a frequency of 905 MHz, served as the radiation source, while a single wire cable pair terminated with a 50-ohm resistor was employed as the victim. The findings reveal that the power transmitted by the source, the distance between the cable and the source, and the polarization angle have a significant impact on the electromagnetic interference received by the cable. Notably, a perpendicular orientation of the cable to the interference source (antenna) in the far-field yielded a reduction of up to 15 dBm in EMI. The results underscore the necessity for more sophisticated models and comprehensive measurements to fully comprehend the diverse factors affecting polarization losses in practical scenarios.
- 1 February 2024
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 14 (1) , 22-30
Open AccessUnconsidered but influencing interference in unmanned aerial vehicle cabling system
The increasing complexity of electrical and electronic systems in unmanned aerial vehicles (UAVs) has raised concerns regarding unwanted electromagnetic interference (EMI) due to limited compartment space. Recent studies have highlighted the UAV cabling as the primary pathway for interference. This paper presents a novel approach to investigating the effects of interference power, polarization angle, and distance from the interference source on EMI in UAV cable systems. Measurements and simulations were performed to analyze the influence of these factors on the radiation received by the cable. A linear dipole antenna, operating at a frequency of 905 MHz, served as the radiation source, while a single wire cable pair terminated with a 50-ohm resistor was employed as the victim. The findings reveal that the power transmitted by the source, the distance between the cable and the source, and the polarization angle have a significant impact on the electromagnetic interference received by the cable. Notably, a perpendicular orientation of the cable to the interference source (antenna) in the far-field yielded a reduction of up to 15 dBm in EMI. The results underscore the necessity for more sophisticated models and comprehensive measurements to fully comprehend the diverse factors affecting polarization losses in practical scenarios.
- 23 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 153-157
Design of IP Satellite Communication for Real Time UAV Telemetry Case: Japan – Indonesia Link
This paper presents the design of real-time communication for UAV using an L-band geostationary satellite. The data latency from UAV to GCS and backward are analyzed to broaden the quality of its communication and real-time data. The major data that is used in UAV consists of telemetry, command, and control. Then, all data are passed on a satellite IP network using VPN and UDP protocol link. Four-parameter analyses such as flight mode, attitude response, waypoint response, and joystick response are applied when evaluating data results. The communication link designed in this study is the connectivity between GCS located at Chiba University of Japan and UAV at Pustekbang-LAPAN Bogor, Indonesia. Latency values from several parameters have been presented. Latency data is used to represent real-time data received by GCS to UAV and vice versa. In short, the latency is 2.742 s for manual - auto flight mode, 1.736 s for attitude response right roller, 1.474 s for pitch up, 20.612 s for reading waypoint, and 0.244 s for elevators joystick response. Furthermore, these data will be considered when developing UAV satellite communication systems.
- 23 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 153-157
Design of IP Satellite Communication for Real Time UAV Telemetry Case: Japan – Indonesia Link
This paper presents the design of real-time communication for UAV using an L-band geostationary satellite. The data latency from UAV to GCS and backward are analyzed to broaden the quality of its communication and real-time data. The major data that is used in UAV consists of telemetry, command, and control. Then, all data are passed on a satellite IP network using VPN and UDP protocol link. Four-parameter analyses such as flight mode, attitude response, waypoint response, and joystick response are applied when evaluating data results. The communication link designed in this study is the connectivity between GCS located at Chiba University of Japan and UAV at Pustekbang-LAPAN Bogor, Indonesia. Latency values from several parameters have been presented. Latency data is used to represent real-time data received by GCS to UAV and vice versa. In short, the latency is 2.742 s for manual - auto flight mode, 1.736 s for attitude response right roller, 1.474 s for pitch up, 20.612 s for reading waypoint, and 0.244 s for elevators joystick response. Furthermore, these data will be considered when developing UAV satellite communication systems.