Ivo Szurman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ivo Szurman has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
- Katerina Skotnicova
Faculty of Materials Science and Technology VSB – Technical University of Ostrava Ostrava Czech Republic
5 shared publications - Pavel Novák
Faculty of Applied Sciences, University of West Bohemia
4 shared publications - Alena Michalcová
Department of Metals and Corrosion Engineering, University of Chemistry and Technology in Prague, Technická 5, 166 28 Prague 6, Czech Republic
2 shared publications - Filip Průša
Department of Metals and Corrosion Engineering, University of Chemistry and Technology, Technická 5, 166 28 Prague, Czech Republic
2 shared publications - Jiří Duda2 shared publications
Petr Suchánek
2 shared publications
Latest Publications
- 27 October 2026
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 979
Strengthening of a Co–Cr–Fe–Ni high-entropy alloy through minor Ta, Al, and C additions and rotary forging
- 27 October 2026
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 979
Strengthening of a Co–Cr–Fe–Ni high-entropy alloy through minor Ta, Al, and C additions and rotary forging
- 22 October 2026
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1084
High-temperature oxidation and thermal stability of FeAl-FeSi composites
- 22 October 2026
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1084
High-temperature oxidation and thermal stability of FeAl-FeSi composites
- 30 August 2026
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1080
High-temperature oxidation and thermal stability of NiAl-FeSi composites
- 30 August 2026
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1080
High-temperature oxidation and thermal stability of NiAl-FeSi composites
- Open Access
- 13 July 2026
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 26 (2) , 206-211
New 3003 Based Aluminium Alloy for Automotive Industry
It is estimated that up to 30 % of all human related green-house gases (GHGs) emissions in developed countries come from transport. Aluminium alloys are very popular materials for achieving weight reduction in new vehicles, thereby reducing fuel consumption and associated GHGs emissions. Unfortunately, the aluminium industry itself has a very harsh environmental impact. In order to achieve an overall GHGs emissions reduction, new aluminium alloys suitable for recycling need to be designed. The aim of this work is to present new fully recycled aluminium alloy for automotive applications based on modified composition of EN AW-3003 which allows higher impurity content. The microstructure and the mechanical properties of the new material are studied by optical microscopy and tensile tests in as-cast temper and as a 2.5 mm thick sheet in various heat treatment conditions. The results are compared with standard EN AW 3003 alloy and show that the properties of both alloys are relatively close.
- 13 July 2026
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 26 (2) , 206-211
Open AccessNew 3003 Based Aluminium Alloy for Automotive Industry
It is estimated that up to 30 % of all human related green-house gases (GHGs) emissions in developed countries come from transport. Aluminium alloys are very popular materials for achieving weight reduction in new vehicles, thereby reducing fuel consumption and associated GHGs emissions. Unfortunately, the aluminium industry itself has a very harsh environmental impact. In order to achieve an overall GHGs emissions reduction, new aluminium alloys suitable for recycling need to be designed. The aim of this work is to present new fully recycled aluminium alloy for automotive applications based on modified composition of EN AW-3003 which allows higher impurity content. The microstructure and the mechanical properties of the new material are studied by optical microscopy and tensile tests in as-cast temper and as a 2.5 mm thick sheet in various heat treatment conditions. The results are compared with standard EN AW 3003 alloy and show that the properties of both alloys are relatively close.
- Open Access
- 30 May 2026
- Published by Elsevier in SSRN Electronic Journal
Microstructure and phase evolution in cast FeSi–NiAl in-situ composites
Fe–Si–Ni–Al-based in-situ composites were synthesized using vacuum induction melting followed by centrifugal casting. The resulting microstructures exhibited characteristic features of in-situ composites, with FeSi forming directly during solidification and acting as the primary reinforcing phase within a NiAl-based matrix. In the as-cast state, the microstructure and phase composition were heterogeneous, and metastable ternary phases, including AlNi₂Si and Al₂FeSi, were identified. Heat treatment promoted chemical homogenization and phase stabilization, leading to the transformation of metastable phases into a stable two-phase microstructure composed of FeSi and NiAl. The microstructural evolution was found to depend strongly on the FeSi:NiAl ratio, corresponding to different regimes within a pseudobinary FeSi–NiAl system. Microhardness showed a strong dependence on FeSi content, with maximum values exceeding 1100 HV0.1 for FeSi-rich compositions. Tribological behavior was governed by a combination of abrasive and adhesive wear mechanisms, with improved wear resistance observed after heat treatment in FeSi-rich alloys. The mechanical and tribological properties of the cast composites were comparable to those of high-performance tool steel Vanadis 6. These results demonstrate that FeSi–NiAl in-situ composites prepared by casting can achieve competitive performance with powder metallurgy-derived materials, while offering advantages in terms of processing simplicity and scalability.
- 30 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMicrostructure and phase evolution in cast FeSi–NiAl in-situ composites
Fe–Si–Ni–Al-based in-situ composites were synthesized using vacuum induction melting followed by centrifugal casting. The resulting microstructures exhibited characteristic features of in-situ composites, with FeSi forming directly during solidification and acting as the primary reinforcing phase within a NiAl-based matrix. In the as-cast state, the microstructure and phase composition were heterogeneous, and metastable ternary phases, including AlNi₂Si and Al₂FeSi, were identified. Heat treatment promoted chemical homogenization and phase stabilization, leading to the transformation of metastable phases into a stable two-phase microstructure composed of FeSi and NiAl. The microstructural evolution was found to depend strongly on the FeSi:NiAl ratio, corresponding to different regimes within a pseudobinary FeSi–NiAl system. Microhardness showed a strong dependence on FeSi content, with maximum values exceeding 1100 HV0.1 for FeSi-rich compositions. Tribological behavior was governed by a combination of abrasive and adhesive wear mechanisms, with improved wear resistance observed after heat treatment in FeSi-rich alloys. The mechanical and tribological properties of the cast composites were comparable to those of high-performance tool steel Vanadis 6. These results demonstrate that FeSi–NiAl in-situ composites prepared by casting can achieve competitive performance with powder metallurgy-derived materials, while offering advantages in terms of processing simplicity and scalability.
- Open Access
- 8 May 2026
- Published by Springer Nature in Research Square
Condition–Dependent Wetting and Interfacial Degradation of Ni–Fe–Co–Cr and Ni–Fe–Co–Cr–Ti–Al High Entropy Alloys on Industrial Al2O3–SiO2 Refractories
This research investigates the high-temperature interactions between Ni–Fe–Co–Cr and Ni–Fe–Co–Cr–Ti–Al high-entropy alloys and industrial ceramic refractories with high corundum (Al 2 O 3 ) content (approximately 68–85 wt%) and SiO 2 as a secondary component. The primary objective is to assess wettability quantitatively and elucidate interfacial reactions that led to the formation of reaction layers, non-metallic inclusions, and surface contamination during melting and casting. Sessile-drop wetting experiments were conducted using a CLASIC high-temperature observation furnace/heating microscope, capable of operating at temperatures up to 1600°C. Contact angles were evaluated using axisymmetric drop shape analysis. To mitigate oxidation and isolate interactions between the refractory materials and metals, the experiments were conducted either in a vacuum or under a controlled overpressure of ultra-high-purity argon (≥ 99.9999%). Post-experimental analysis of the metal–ceramic interfaces was performed using scanning electron microscopy with EDX microanalysis, along with X-ray powder diffraction, to examine interfacial morphology, elemental distribution, and reaction products. The comprehensive wetting and post-mortem characterizations revealed a direct correlation between composition-dependent wettability and the development of interfacial reaction layers or phases. The findings provide essential guidelines for selecting corundum-rich crucibles and molds, as well as for establishing processing parameters that minimize interfacial degradation, ultimately enhancing casting yield and the reliability of components.
- 8 May 2026
- Published by Springer Nature in Research Square
Open AccessCondition–Dependent Wetting and Interfacial Degradation of Ni–Fe–Co–Cr and Ni–Fe–Co–Cr–Ti–Al High Entropy Alloys on Industrial Al2O3–SiO2 Refractories
This research investigates the high-temperature interactions between Ni–Fe–Co–Cr and Ni–Fe–Co–Cr–Ti–Al high-entropy alloys and industrial ceramic refractories with high corundum (Al 2 O 3 ) content (approximately 68–85 wt%) and SiO 2 as a secondary component. The primary objective is to assess wettability quantitatively and elucidate interfacial reactions that led to the formation of reaction layers, non-metallic inclusions, and surface contamination during melting and casting. Sessile-drop wetting experiments were conducted using a CLASIC high-temperature observation furnace/heating microscope, capable of operating at temperatures up to 1600°C. Contact angles were evaluated using axisymmetric drop shape analysis. To mitigate oxidation and isolate interactions between the refractory materials and metals, the experiments were conducted either in a vacuum or under a controlled overpressure of ultra-high-purity argon (≥ 99.9999%). Post-experimental analysis of the metal–ceramic interfaces was performed using scanning electron microscopy with EDX microanalysis, along with X-ray powder diffraction, to examine interfacial morphology, elemental distribution, and reaction products. The comprehensive wetting and post-mortem characterizations revealed a direct correlation between composition-dependent wettability and the development of interfacial reaction layers or phases. The findings provide essential guidelines for selecting corundum-rich crucibles and molds, as well as for establishing processing parameters that minimize interfacial degradation, ultimately enhancing casting yield and the reliability of components.
- 16 May 2024
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 320
Physical properties of MnFeAl-based alloys affected by Mn content and annealing
- 16 May 2024
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 320
Physical properties of MnFeAl-based alloys affected by Mn content and annealing
- Open Access
- 23 February 2024
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 24 (1) , 104-109
How to Determine Possible Interactions of Silicide and Aluminide in Preparation of Composites
Silicide – aluminide composites could be considered as potential tool materials, because of high wear resistance and thermal stability. Recently, the alloys based on iron aluminide and silicide were tested, but they found to be very brit...
- 23 February 2024
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 24 (1) , 104-109
Open AccessHow to Determine Possible Interactions of Silicide and Aluminide in Preparation of Composites
Silicide – aluminide composites could be considered as potential tool materials, because of high wear resistance and thermal stability. Recently, the alloys based on iron aluminide and silicide were tested, but they found to be very brit...
- Open Access
- 1 August 2021
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1178 (1) , 012028
Preparation of Ti-Al-Si alloys with the various contents of aluminium and silicon
The intermetallics based on Ti-Al system are a relatively new class of high-temperature construction materials that combine unique physical and mechanical properties for use in aircraft engines, industrial gas turbines, or automotive industry. They are characterized by low density, good mechanical properties at high temperatures and good oxidation resistance. Addition of silicon into the Ti-Al alloys improves oxidation resistance and ultimate tensile strength in compression, but the complicated production limits wider use of these Ti-Al-Si intermetallic alloys. In this work, two main technologies of preparation of intermetallic compounds will be compared-melting and powder metallurgy.
- 1 August 2021
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1178 (1) , 012028
Open AccessPreparation of Ti-Al-Si alloys with the various contents of aluminium and silicon
The intermetallics based on Ti-Al system are a relatively new class of high-temperature construction materials that combine unique physical and mechanical properties for use in aircraft engines, industrial gas turbines, or automotive industry. They are characterized by low density, good mechanical properties at high temperatures and good oxidation resistance. Addition of silicon into the Ti-Al alloys improves oxidation resistance and ultimate tensile strength in compression, but the complicated production limits wider use of these Ti-Al-Si intermetallic alloys. In this work, two main technologies of preparation of intermetallic compounds will be compared-melting and powder metallurgy.