Alin Antohe
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Alin Antohe has a total of 89 co-authors. Here are the top co-authors by number of shared publications:
- Marcel W. Pruessner
U.S. Naval Research Laboratory, Optical Sciences Division, Washington, DC, USA
4 shared publications - Nathan F. Tyndall
U.S. Naval Research Laboratory
4 shared publications - Todd H. Stievater
U.S. Naval Research Laboratory
4 shared publications - Kyle J. Walsh
Naval Research Laboratory Washington District of Columbia USA
3 shared publications - Lewis G. Carpenter
American Institute for Manufacturing Integrated Photonics
3 shared publications - Nicholas M. Fahrenkopf
Research Foundation for the State University of New York
3 shared publications
Latest Publications
- Open Access
- 7 November 2026
- Published by Wiley in Nanophotonics
- Vol. 15 (21) , e70350
AIM‐Photonics Visible‐to‐Near‐Infrared Silicon‐Nitride‐Based Silicon‐Photonics Platform and Component Library
Silicon‐photonics platforms operating at visible and near‐infrared wavelengths are essential for a growing range of applications, including biosensing, chemical detection, Raman spectroscopy, quantum, optogenetics, and displays. However, unlike their infrared counterparts, visible‐wavelength platforms have lacked comprehensive component libraries with pre‐characterized devices, limiting the ability to rapidly design photonic integrated circuits for these applications. In this work, we present the design, fabrication, and broadband experimental characterization of a comprehensive visible‐to‐near‐infrared‐spanning component library for the AIM‐Photonics 300‐mm‐wafer silicon‐nitride‐based platform, which features two silicon‐nitride waveguiding layers, a sensing trench, thermo‐optic phase shifters for modulation, and a dicing trench for fiber‐to‐chip edge coupling. We design and characterize components for both the fundamental quasi‐transverse‐electric and quasi‐transverse‐magnetic modes for wavelengths spanning from 450 to 1000 nm. To enable this characterization, we utilize a spectrum‐spanning broadband measurement setup and methodology. The component library includes passive waveguides, edge couplers, grating couplers, multimode‐interferometer splitters, directional couplers with varying splitting ratios, waveguide crossings, interlayer‐transition escalators, polarization rotators, polarization splitters, sensing‐trench components, and thermo‐optic phase shifters. This work provides a foundry‐compatible pre‐characterized library of photonic building blocks that enables the rapid design and deployment of visible‐to‐near‐infrared photonic integrated circuits for sensing, quantum, biomedical, display, and other emerging applications.
- 7 November 2026
- Published by Wiley in Nanophotonics
- Vol. 15 (21) , e70350
Open AccessAIM‐Photonics Visible‐to‐Near‐Infrared Silicon‐Nitride‐Based Silicon‐Photonics Platform and Component Library
Silicon‐photonics platforms operating at visible and near‐infrared wavelengths are essential for a growing range of applications, including biosensing, chemical detection, Raman spectroscopy, quantum, optogenetics, and displays. However, unlike their infrared counterparts, visible‐wavelength platforms have lacked comprehensive component libraries with pre‐characterized devices, limiting the ability to rapidly design photonic integrated circuits for these applications. In this work, we present the design, fabrication, and broadband experimental characterization of a comprehensive visible‐to‐near‐infrared‐spanning component library for the AIM‐Photonics 300‐mm‐wafer silicon‐nitride‐based platform, which features two silicon‐nitride waveguiding layers, a sensing trench, thermo‐optic phase shifters for modulation, and a dicing trench for fiber‐to‐chip edge coupling. We design and characterize components for both the fundamental quasi‐transverse‐electric and quasi‐transverse‐magnetic modes for wavelengths spanning from 450 to 1000 nm. To enable this characterization, we utilize a spectrum‐spanning broadband measurement setup and methodology. The component library includes passive waveguides, edge couplers, grating couplers, multimode‐interferometer splitters, directional couplers with varying splitting ratios, waveguide crossings, interlayer‐transition escalators, polarization rotators, polarization splitters, sensing‐trench components, and thermo‐optic phase shifters. This work provides a foundry‐compatible pre‐characterized library of photonic building blocks that enables the rapid design and deployment of visible‐to‐near‐infrared photonic integrated circuits for sensing, quantum, biomedical, display, and other emerging applications.
- Open Access
- 1 April 2026
- Published by AIP Publishing in APL Photonics
- Vol. 11 (4)
Waveguide-based measurement of the silicon nitride refractive index and thermo-optic coefficient from the visible to the near-infrared
We describe a method to experimentally determine the refractive index and thermo-optic coefficient of waveguides fabricated from low-pressure chemical vapor deposition silicon nitride over a broad wavelength range (500–1600 nm) using Mach–Zehnder interferometers. Silicon nitride refractive index Sellmeier coefficients are extracted with a weighted root mean squared deviation that is typically better than 0.04% from the visible to the near-infrared. The thermo-optic coefficient of silicon nitride is measured over a similar wavelength range and shows a significant increase at visible wavelengths compared to the value in the near-infrared. Accurate knowledge of the waveguide core and cladding refractive indices and thermo-optic coefficients in foundry-based photonic integrated circuits allows for successful first-time design of passive and active components. This method can be used with any transparent waveguide material and can be automated for process monitoring and wafer-scale verification.
- 1 April 2026
- Published by AIP Publishing in APL Photonics
- Vol. 11 (4)
Open AccessWaveguide-based measurement of the silicon nitride refractive index and thermo-optic coefficient from the visible to the near-infrared
We describe a method to experimentally determine the refractive index and thermo-optic coefficient of waveguides fabricated from low-pressure chemical vapor deposition silicon nitride over a broad wavelength range (500–1600 nm) using Mach–Zehnder interferometers. Silicon nitride refractive index Sellmeier coefficients are extracted with a weighted root mean squared deviation that is typically better than 0.04% from the visible to the near-infrared. The thermo-optic coefficient of silicon nitride is measured over a similar wavelength range and shows a significant increase at visible wavelengths compared to the value in the near-infrared. Accurate knowledge of the waveguide core and cladding refractive indices and thermo-optic coefficients in foundry-based photonic integrated circuits allows for successful first-time design of passive and active components. This method can be used with any transparent waveguide material and can be automated for process monitoring and wafer-scale verification.
- Open Access
- 18 February 2026
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 25 (2) , 024055
Low-crosstalk silicon-fabricated optical waveguides for laser delivery to matter qubits
Reliable control of quantum information in matter-based qubits requires precisely applied external fields, and unaccounted-for spatial crosstalk of these fields between adjacent qubits leads to loss of fidelity. We report a CMOS foundry-produced microfabricated silicon nitride ( Si 3 N 4 ) optical waveguide for addressing a chain of eight unequally spaced trapped barium ions, with crosstalk compatible with scalable quantum information processing. The crosstalk-mitigation techniques incorporated into the chip design result in a reduction of the measured optical field by at least 50.8(1.3) dB between adjacent waveguide outputs near 650 nm and similar behavior for devices designed for 493 nm and 585 nm. The waveguide outputs near 650 nm, along with a global laser near 493 nm, have been used to laser cool a chain of eight 138 Ba + ions, and a camera has imaged the resulting fluorescence at 493 nm.
- 18 February 2026
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 25 (2) , 024055
Open AccessLow-crosstalk silicon-fabricated optical waveguides for laser delivery to matter qubits
Reliable control of quantum information in matter-based qubits requires precisely applied external fields, and unaccounted-for spatial crosstalk of these fields between adjacent qubits leads to loss of fidelity. We report a CMOS foundry-produced microfabricated silicon nitride ( Si 3 N 4 ) optical waveguide for addressing a chain of eight unequally spaced trapped barium ions, with crosstalk compatible with scalable quantum information processing. The crosstalk-mitigation techniques incorporated into the chip design result in a reduction of the measured optical field by at least 50.8(1.3) dB between adjacent waveguide outputs near 650 nm and similar behavior for devices designed for 493 nm and 585 nm. The waveguide outputs near 650 nm, along with a global laser near 493 nm, have been used to laser cool a chain of eight 138 Ba + ions, and a camera has imaged the resulting fluorescence at 493 nm.
- 20 October 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33 (22) , 45631-45643
Extracting the core and cladding contributions to fluorescence and Raman emission in integrated photonic waveguides
Minimizing background optical emission originating from waveguides is critical for achieving high-sensitivity performance in integrated photonic platforms, particularly for applications in biosensing, chemical detection, environmental monitoring, and quantum sensors. These background signals, often stemming from intrinsic fluorescence (also known as autofluorescence or photoluminescence) or Raman scattering in the waveguide core or cladding, can obscure weak optical signals and limit the accuracy of integrated photonic sensors. In this work, we introduce a novel parameter-extraction technique that quantitatively separates waveguide losses and background-generation efficiency, and identifies the individual contributions of the waveguide core and cladding to the total background signal. Our method utilizes only standard photonic waveguides and requires no specialized sample preparation or auxiliary test wafers. We validate our technique experimentally by characterizing silicon-nitride waveguides across nine wafers fabricated in a 300-mm-wafer platform developed at AIM Photonics. Applying our parameter-extraction method, we demonstrate its utility in showing a clear correlation between waveguide propagation loss and fluorescence, and its sensitivity in resolving material-specific differences in Raman spectra between wafers fabricated using different processes, including those arising from hydrogen-related impurities in non-annealed cores. This work provides a practical and comprehensive tool for quantifying, diagnosing, and reducing material-specific propagation loss and background signals in integrated photonic waveguides, ultimately enabling more effective development of low-noise and low-loss photonics platforms.
- 20 October 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33 (22) , 45631-45643
Extracting the core and cladding contributions to fluorescence and Raman emission in integrated photonic waveguides
Minimizing background optical emission originating from waveguides is critical for achieving high-sensitivity performance in integrated photonic platforms, particularly for applications in biosensing, chemical detection, environmental monitoring, and quantum sensors. These background signals, often stemming from intrinsic fluorescence (also known as autofluorescence or photoluminescence) or Raman scattering in the waveguide core or cladding, can obscure weak optical signals and limit the accuracy of integrated photonic sensors. In this work, we introduce a novel parameter-extraction technique that quantitatively separates waveguide losses and background-generation efficiency, and identifies the individual contributions of the waveguide core and cladding to the total background signal. Our method utilizes only standard photonic waveguides and requires no specialized sample preparation or auxiliary test wafers. We validate our technique experimentally by characterizing silicon-nitride waveguides across nine wafers fabricated in a 300-mm-wafer platform developed at AIM Photonics. Applying our parameter-extraction method, we demonstrate its utility in showing a clear correlation between waveguide propagation loss and fluorescence, and its sensitivity in resolving material-specific differences in Raman spectra between wafers fabricated using different processes, including those arising from hydrogen-related impurities in non-annealed cores. This work provides a practical and comprehensive tool for quantifying, diagnosing, and reducing material-specific propagation loss and background signals in integrated photonic waveguides, ultimately enabling more effective development of low-noise and low-loss photonics platforms.
- 2 September 2025
- Published by Optica Publishing Group in Optics Letters
- Vol. 50 (18) , 5578-5581
300 mm wafer-scale SiN platform for broadband soliton microcombs compatible with alkali atomic references
Chip-integrated optical frequency combs (OFCs) based on Kerr nonlinear resonators are of great significance given their scalability and wide range of applications. Broadband on-chip OFCs reaching visible wavelengths are especially valuable as they address atomic clock transitions that play an important role in position, navigation, and timing infrastructure. Silicon nitride (SiN) deposited via low-pressure chemical vapor deposition (LPCVD) is the usual platform for chip-integrated OFCs, due to its low absorption and repeatable dispersion, and such fabrication is now standard at wafer sizes up to 200 mm. However, the LPCVD high temperature and film stress pose challenges in scaling to larger wafers and integrating with electronic and photonic devices. Here, we report the linear performance and broadband frequency comb generation from microring resonators fabricated on 300 mm wafers at AIM Photonics, using a lower temperature, lower stress plasma-enhanced chemical vapor deposition process suitable for thick (≈700 nm) SiN films and compatible with electronic and photonic integration. The platform exhibits consistent insertion loss, high intrinsic quality factor, and thickness variation of ±2% across the whole 300 mm wafer. We demonstrate broadband soliton microcomb generation with a lithographically tunable dispersion profile extending to wavelengths of common alkali atom transitions. These results are a step towards more highly integrated and mass-manufacturable devices, enabling advanced applications including optical clocks, LiDAR, and beyond.
- 2 September 2025
- Published by Optica Publishing Group in Optics Letters
- Vol. 50 (18) , 5578-5581
300 mm wafer-scale SiN platform for broadband soliton microcombs compatible with alkali atomic references
Chip-integrated optical frequency combs (OFCs) based on Kerr nonlinear resonators are of great significance given their scalability and wide range of applications. Broadband on-chip OFCs reaching visible wavelengths are especially valuable as they address atomic clock transitions that play an important role in position, navigation, and timing infrastructure. Silicon nitride (SiN) deposited via low-pressure chemical vapor deposition (LPCVD) is the usual platform for chip-integrated OFCs, due to its low absorption and repeatable dispersion, and such fabrication is now standard at wafer sizes up to 200 mm. However, the LPCVD high temperature and film stress pose challenges in scaling to larger wafers and integrating with electronic and photonic devices. Here, we report the linear performance and broadband frequency comb generation from microring resonators fabricated on 300 mm wafers at AIM Photonics, using a lower temperature, lower stress plasma-enhanced chemical vapor deposition process suitable for thick (≈700 nm) SiN films and compatible with electronic and photonic integration. The platform exhibits consistent insertion loss, high intrinsic quality factor, and thickness variation of ±2% across the whole 300 mm wafer. We demonstrate broadband soliton microcomb generation with a lithographically tunable dispersion profile extending to wavelengths of common alkali atom transitions. These results are a step towards more highly integrated and mass-manufacturable devices, enabling advanced applications including optical clocks, LiDAR, and beyond.
- 7 April 2025
- Published by Optica Publishing Group in Optics Letters
- Vol. 50 (8) , 2570-2573
Implementing photonic-crystal resonator frequency combs in a photonic foundry
We explore an AIM Photonics silicon nitride platform to fabricate photonic-crystal resonators (PhCRs) for generating optical parametric oscillators (OPOs) and soliton microcombs. Our approach leverages the scalability and fine feature size of silicon nitride processing on large-scale silicon wafers to achieve low-loss, high-Q microresonators, functionalized by nanoscale photonic-crystal structures. We demonstrate an intrinsic microresonator quality factor up to 1.2 × 107 with complete foundry fabrication on 300 mm silicon, a 700 nm thick silicon nitride device layer, and inclusion of complex nanophotonics. These features enable a host of nonlinear nanophotonic sources on the platform, including OPOs, microcombs, parametric amplifiers, squeezed-light generators, and single-photon sources. By fine-tuning the photonic-crystal design parameters, we achieve broad tunability in the frequency of the OPO output, spanning a significant portion of the near-infrared. Additionally, we observe the formation of soliton frequency combs, enabled by the precise dispersion engineering of the microresonators. These results highlight the potential of widely accessible, photolithographically patterned, silicon nitride photonics to enable wide access to and complex integration of frequency comb sources, with applications in spectroscopy, metrology, and communications.
- 7 April 2025
- Published by Optica Publishing Group in Optics Letters
- Vol. 50 (8) , 2570-2573
Implementing photonic-crystal resonator frequency combs in a photonic foundry
We explore an AIM Photonics silicon nitride platform to fabricate photonic-crystal resonators (PhCRs) for generating optical parametric oscillators (OPOs) and soliton microcombs. Our approach leverages the scalability and fine feature size of silicon nitride processing on large-scale silicon wafers to achieve low-loss, high-Q microresonators, functionalized by nanoscale photonic-crystal structures. We demonstrate an intrinsic microresonator quality factor up to 1.2 × 107 with complete foundry fabrication on 300 mm silicon, a 700 nm thick silicon nitride device layer, and inclusion of complex nanophotonics. These features enable a host of nonlinear nanophotonic sources on the platform, including OPOs, microcombs, parametric amplifiers, squeezed-light generators, and single-photon sources. By fine-tuning the photonic-crystal design parameters, we achieve broad tunability in the frequency of the OPO output, spanning a significant portion of the near-infrared. Additionally, we observe the formation of soliton frequency combs, enabled by the precise dispersion engineering of the microresonators. These results highlight the potential of widely accessible, photolithographically patterned, silicon nitride photonics to enable wide access to and complex integration of frequency comb sources, with applications in spectroscopy, metrology, and communications.
- 22 April 2024
- Published by Optica Publishing Group in Optics Express
- Vol. 32 (10) , 16702-16711
Broadband silicon nitride integrated polarization rotators at 780 nm
Polarization management, and in particular polarization rotation, is becoming increasingly important for photonic integrated circuits (PICs). While fiber-optic networks are generally polarization insensitive, the large aspect ratio of high-index-contrast PIC waveguides leads to a large polarization-dependent response of integrated components such as waveguides, optical cavities, couplers, etc. Although foundry-processed polarization rotators operating at telecom and datacom wavelengths (C- and O-band) have been demonstrated, to date, there have been few reports of devices operating at shorter wavelengths. This work demonstrates silicon nitride (SiN) polarization rotators operating from λ=700-1000 nm (the I/Z-band) that take advantage of optical coupling between two waveguiding layers in a standard foundry process. We demonstrate a broadband white-light polarization measurement setup that enables precise characterization of the polarization-dependent transmission of photonic waveguide devices. Measurements on foundry-processed devices confirm full TE-to-TM rotation exhibiting a maximum polarization extinction ratio (PER) approaching 20 dB (limited by our measurement setup), and an exceptionally large bandwidth of up to 160 nm with an insertion loss less than 0.2 dB. Beam propagation method (3D-BPM) simulations show good agreement with experimental data and enable the device parameters to be adjusted to accommodate different operating wavelengths and geometries with no changes to the existing foundry process. This work opens up opportunities for applications in quantum information and bio-sensing where operation at λ<1000nm is needed.
- 22 April 2024
- Published by Optica Publishing Group in Optics Express
- Vol. 32 (10) , 16702-16711
Broadband silicon nitride integrated polarization rotators at 780 nm
Polarization management, and in particular polarization rotation, is becoming increasingly important for photonic integrated circuits (PICs). While fiber-optic networks are generally polarization insensitive, the large aspect ratio of high-index-contrast PIC waveguides leads to a large polarization-dependent response of integrated components such as waveguides, optical cavities, couplers, etc. Although foundry-processed polarization rotators operating at telecom and datacom wavelengths (C- and O-band) have been demonstrated, to date, there have been few reports of devices operating at shorter wavelengths. This work demonstrates silicon nitride (SiN) polarization rotators operating from λ=700-1000 nm (the I/Z-band) that take advantage of optical coupling between two waveguiding layers in a standard foundry process. We demonstrate a broadband white-light polarization measurement setup that enables precise characterization of the polarization-dependent transmission of photonic waveguide devices. Measurements on foundry-processed devices confirm full TE-to-TM rotation exhibiting a maximum polarization extinction ratio (PER) approaching 20 dB (limited by our measurement setup), and an exceptionally large bandwidth of up to 160 nm with an insertion loss less than 0.2 dB. Beam propagation method (3D-BPM) simulations show good agreement with experimental data and enable the device parameters to be adjusted to accommodate different operating wavelengths and geometries with no changes to the existing foundry process. This work opens up opportunities for applications in quantum information and bio-sensing where operation at λ<1000nm is needed.
- Open Access
- 1 January 2024
- Published by AIP Publishing in APL Photonics
- Vol. 9 (1)
Optical and geometric parameter extraction across 300-mm photonic integrated circuit wafers
The precise quantification of a dielectric waveguide core thickness, core width, core refractive index, and cladding refractive index across a wafer is critical for greater consistency and accuracy in photonic circuit fabrication. However, accurate wafer-scale measurements of these parameters have not yet been demonstrated. We have previously described a method for extracting these four parameters simultaneously from silicon nitride waveguides using unbalanced Mach–Zehnder interferometers on a single die. In this work, we show that this technique can be scaled to characterize these photonic parameters across an entire 300 mm wafer. The refractive indices of the core and cladding materials are found with relative standard deviations of the mean of 0.07% and 0.03%, respectively. The core width offset (bias) and thickness are found with relative standard deviations of 0.3% (2.6 nm) and 0.5% (1.1 nm), respectively. The extracted parameter maps suggest a radial variation of material indices and a planar variation of geometric parameters. We verify the extracted parameters by accurately predicting the performance of an unbalanced Mach–Zehnder interferometer and the degeneracy between different modes in straight waveguides.
- 1 January 2024
- Published by AIP Publishing in APL Photonics
- Vol. 9 (1)
Open AccessOptical and geometric parameter extraction across 300-mm photonic integrated circuit wafers
The precise quantification of a dielectric waveguide core thickness, core width, core refractive index, and cladding refractive index across a wafer is critical for greater consistency and accuracy in photonic circuit fabrication. However, accurate wafer-scale measurements of these parameters have not yet been demonstrated. We have previously described a method for extracting these four parameters simultaneously from silicon nitride waveguides using unbalanced Mach–Zehnder interferometers on a single die. In this work, we show that this technique can be scaled to characterize these photonic parameters across an entire 300 mm wafer. The refractive indices of the core and cladding materials are found with relative standard deviations of the mean of 0.07% and 0.03%, respectively. The core width offset (bias) and thickness are found with relative standard deviations of 0.3% (2.6 nm) and 0.5% (1.1 nm), respectively. The extracted parameter maps suggest a radial variation of material indices and a planar variation of geometric parameters. We verify the extracted parameters by accurately predicting the performance of an unbalanced Mach–Zehnder interferometer and the degeneracy between different modes in straight waveguides.
- 8 February 2007
- Published by SPIE-Intl Soc Optical Eng
- Vol. 6533, 653318-653318-5
Quantitative measurement of EUV resist outgassing
The Mo/Si multilayer mirrors used for extreme ultraviolet (EUV) lithography can become contaminated during exposure in the presence of some hydrocarbons [1-3]. Because this leads to a loss in the reflectivity of the optics and throughput of the exposure tools, it needs to be avoided. Since photoresists are known to outgas during exposure to EUV radiation in a vacuum environment, the careful choice of materials is important to preserving the EUV optics. Work therefore has been performed to measure the species and quantities of molecules that outgas from EUV resists when exposed to EUV radiation [4-7].
- 8 February 2007
- Published by SPIE-Intl Soc Optical Eng
- Vol. 6533, 653318-653318-5
Quantitative measurement of EUV resist outgassing
The Mo/Si multilayer mirrors used for extreme ultraviolet (EUV) lithography can become contaminated during exposure in the presence of some hydrocarbons [1-3]. Because this leads to a loss in the reflectivity of the optics and throughput of the exposure tools, it needs to be avoided. Since photoresists are known to outgas during exposure to EUV radiation in a vacuum environment, the careful choice of materials is important to preserving the EUV optics. Work therefore has been performed to measure the species and quantities of molecules that outgas from EUV resists when exposed to EUV radiation [4-7].