Xiongjie Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Xiongjie Zhang has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Pui-In Mak
University of Macau
6 shared publications - Rui Paulo Martins
University of Macau
6 shared publications - Yang Jiang
University of Macau
5 shared publications - Anyang Zhao
University of Macau
4 shared publications - Man-Kay Law
University of Macau
4 shared publications - Qiaobo Ma
Institute of Microelectronics
3 shared publications
Latest Publications
- 1 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (10) , 3192-3203
A Cross-Coupled Hybrid Switched-Capacitor Buck Converter With Extended Conversion Range and Enhanced DCR Loss Reduction
This article presents a hybrid switched-capacitor (SC) buck converter designed to optimize the reduction in inductor average current ( $I_{L,\mathrm{DC}})$ across a wide voltage conversion ratio (VCR) range for Li-ion battery-powered systems. The proposed topology is bases on a modified dual-path (DP) hybrid power stage structure and elevates the inductor de-energizing voltage to enhance $I_{L,\mathrm{DC}}$ reduction. With a dual-branch interleaved cross-coupled structure, it reduces the required number of SC cells, thereby lowering costs. Moreover, the converter attains a seamless switching-phase transition around VCR of 0.5, ensuring smooth operations and simplifying control complexity. A stable efficiency is maintained across the entire VCR range by balancing inductor DC resistance (DCR) loss and switch/path conduction loss. In the circuit design aspect, a two-quadrant level shifter (2QLS) is proposed to meet power switch driving requirements in a positive-negative wide-range floating domain. Fabricated in a 180-nm BCD process with a 4.42 mm $^{2}$ chip area, the converter prototype attains a peak conversion efficiency of 91% when converting a 2.7 $\sim$ 4.2 V input to a 1 $\sim$ 1.8 V output. It delivers a maximum load current of 4.2 A using two 4.7- $\mu $ H inductors with 175 m $\Omega $ DCR in 16.7 mm $^{3}$ each and achieves an average efficiency of 90% with only 1.5% variation.
- 1 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (10) , 3192-3203
A Cross-Coupled Hybrid Switched-Capacitor Buck Converter With Extended Conversion Range and Enhanced DCR Loss Reduction
This article presents a hybrid switched-capacitor (SC) buck converter designed to optimize the reduction in inductor average current ( $I_{L,\mathrm{DC}})$ across a wide voltage conversion ratio (VCR) range for Li-ion battery-powered systems. The proposed topology is bases on a modified dual-path (DP) hybrid power stage structure and elevates the inductor de-energizing voltage to enhance $I_{L,\mathrm{DC}}$ reduction. With a dual-branch interleaved cross-coupled structure, it reduces the required number of SC cells, thereby lowering costs. Moreover, the converter attains a seamless switching-phase transition around VCR of 0.5, ensuring smooth operations and simplifying control complexity. A stable efficiency is maintained across the entire VCR range by balancing inductor DC resistance (DCR) loss and switch/path conduction loss. In the circuit design aspect, a two-quadrant level shifter (2QLS) is proposed to meet power switch driving requirements in a positive-negative wide-range floating domain. Fabricated in a 180-nm BCD process with a 4.42 mm $^{2}$ chip area, the converter prototype attains a peak conversion efficiency of 91% when converting a 2.7 $\sim$ 4.2 V input to a 1 $\sim$ 1.8 V output. It delivers a maximum load current of 4.2 A using two 4.7- $\mu $ H inductors with 175 m $\Omega $ DCR in 16.7 mm $^{3}$ each and achieves an average efficiency of 90% with only 1.5% variation.
- 19 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (5) , 2579-2583
A 12V-to-1V Outphase-Interleaved SC Hybrid Converter With Enhanced Inductor De-Energizing Slew Rate and Adaptive Deadtime Control
This brief presents a high step-down outphase-interleaved switched-capacitor hybrid converter with enhanced inductor DC current reduction and flying-capacitor (CF) inrush current suppression for 12V-to-1V voltage conversion, which is appealing in automotive and date center applications. The main novelties and contribution of this work are three folds: 1) a hybrid converter topology with well-reduced inductor DC (IL,DC) current and CF inrush current to achieve high conversion efficiency and power density for high step-down conversions, 2) an adaptive dead-time (ADT) controller for minimizing the body diode conduction loss adaptive to different load condition, and 3) a body diode series conduction (BDSC) technique for enhancing heavy-to-light load transient response. Implemented in a 180-nm Bipolar-CMOS-DMOS (BCD) process alongside total power passive components in a 4.84 mm3 volume, the proposed converter achieves a peak efficiency of 91.1% for 12V-to-1V conversion at a load current (ILOAD) of 0.8A. It retains an efficiency of 83.9% at 2.5A ILOAD. The ADT control improves light-load efficiency by ~1%. When ILOAD steps from a 2.5A to 0.5A under 12V-to-0.6V conversion, the proposed BDSC technique boosts the inductor de-energizing SR by 1.8× and reduces output overshoot by 46mV.
- 19 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (5) , 2579-2583
A 12V-to-1V Outphase-Interleaved SC Hybrid Converter With Enhanced Inductor De-Energizing Slew Rate and Adaptive Deadtime Control
This brief presents a high step-down outphase-interleaved switched-capacitor hybrid converter with enhanced inductor DC current reduction and flying-capacitor (CF) inrush current suppression for 12V-to-1V voltage conversion, which is appealing in automotive and date center applications. The main novelties and contribution of this work are three folds: 1) a hybrid converter topology with well-reduced inductor DC (IL,DC) current and CF inrush current to achieve high conversion efficiency and power density for high step-down conversions, 2) an adaptive dead-time (ADT) controller for minimizing the body diode conduction loss adaptive to different load condition, and 3) a body diode series conduction (BDSC) technique for enhancing heavy-to-light load transient response. Implemented in a 180-nm Bipolar-CMOS-DMOS (BCD) process alongside total power passive components in a 4.84 mm3 volume, the proposed converter achieves a peak efficiency of 91.1% for 12V-to-1V conversion at a load current (ILOAD) of 0.8A. It retains an efficiency of 83.9% at 2.5A ILOAD. The ADT control improves light-load efficiency by ~1%. When ILOAD steps from a 2.5A to 0.5A under 12V-to-0.6V conversion, the proposed BDSC technique boosts the inductor de-energizing SR by 1.8× and reduces output overshoot by 46mV.
- 9 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (4) , 1078-1092
An Outphase-Interleaved Switched-Capacitor Hybrid Buck Converter With Relieved Capacitor Inrush Current and COUT-Free Operations
This article presents an efficient buck converter design using the proposed outphase-interleaved hybrid switched-capacitor (OISC) topology. The outphase-interleaved switched-capacitor (SC) cells significantly extend the $C_{\mathrm{F}}$ charge-balancing phase without disturbing the inductor volt-second balance (VSB), while doubling the effective inductor switching frequency for reduced current ripple. As a result, it addresses the intrinsic issue of sharply increased flying capacitor ( $C_{\mathrm{F}})$ inrush current in existing SC dual-/multi-path (DP/MP) hybrid buck converters under extreme duty ratios, resolving the tradeoff between SC cell conduction loss and inductor dc current ( $I_{{L,}\mathrm{dc}})$ reduction capability. The proposed topology attains three key advantages: 1) relived $C_{\mathrm{F}}$ hard-charging-induced inrush current; 2) reduced $I_{{L,}\mathrm{dc}}$ ; and 3) power stage normal operation without relying on an output capacitor $(C_{\mathrm{OUT}})$ , resulting in improved conversion efficiency and power density. To enhance the overall power density and mitigate gate-driving path ringing, we propose an area-efficient fully on-chip gate-driving scheme with a shared charge pump (CP), ensuring proper operations with all-NMOS power switches. Fabricated in a 180-nm CMOS process with 7.63 mm $^{2}$ chip area, the converter achieves a peak conversion efficiency of 97.3% and an overall peak current density of 585 mA/mm $^{3}$ at 90.1% efficiency. Supporting a load current ( $I_{\mathrm{LOAD}})$ from 0.05 to 3.1 A, it converts 1.8–3.3 V input to 0.8–1.8 V output. Measured output voltage ( $V_{\mathrm{OUT}})$ ripple is $\sim$ 3.3% of $V_{\mathrm{OUT}}$ dc under 3.1 A $I_{\mathrm{LOAD}}$ with zero $C_{\mathrm{OUT}}$ .
- 9 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (4) , 1078-1092
An Outphase-Interleaved Switched-Capacitor Hybrid Buck Converter With Relieved Capacitor Inrush Current and COUT-Free Operations
This article presents an efficient buck converter design using the proposed outphase-interleaved hybrid switched-capacitor (OISC) topology. The outphase-interleaved switched-capacitor (SC) cells significantly extend the $C_{\mathrm{F}}$ charge-balancing phase without disturbing the inductor volt-second balance (VSB), while doubling the effective inductor switching frequency for reduced current ripple. As a result, it addresses the intrinsic issue of sharply increased flying capacitor ( $C_{\mathrm{F}})$ inrush current in existing SC dual-/multi-path (DP/MP) hybrid buck converters under extreme duty ratios, resolving the tradeoff between SC cell conduction loss and inductor dc current ( $I_{{L,}\mathrm{dc}})$ reduction capability. The proposed topology attains three key advantages: 1) relived $C_{\mathrm{F}}$ hard-charging-induced inrush current; 2) reduced $I_{{L,}\mathrm{dc}}$ ; and 3) power stage normal operation without relying on an output capacitor $(C_{\mathrm{OUT}})$ , resulting in improved conversion efficiency and power density. To enhance the overall power density and mitigate gate-driving path ringing, we propose an area-efficient fully on-chip gate-driving scheme with a shared charge pump (CP), ensuring proper operations with all-NMOS power switches. Fabricated in a 180-nm CMOS process with 7.63 mm $^{2}$ chip area, the converter achieves a peak conversion efficiency of 97.3% and an overall peak current density of 585 mA/mm $^{3}$ at 90.1% efficiency. Supporting a load current ( $I_{\mathrm{LOAD}})$ from 0.05 to 3.1 A, it converts 1.8–3.3 V input to 0.8–1.8 V output. Measured output voltage ( $V_{\mathrm{OUT}})$ ripple is $\sim$ 3.3% of $V_{\mathrm{OUT}}$ dc under 3.1 A $I_{\mathrm{LOAD}}$ with zero $C_{\mathrm{OUT}}$ .
- 11 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (12) , 15109-15114
A 12/24 V-Input HV-LV-Separated Hybrid SC PoL Converter With 355 mW/mm3 Power Density at 3 A Load Current and 15.2 mm3 Power Passives
This letter presents a high-power-density point-of-load (PoL) DC-DC converter for 12/24 V input applications, using the proposed high voltage-low voltage (HV-LV) separated hybrid switched-capacitor (SC) topology. By incorporating inductors between the SC networks in HV/LV domains, the design achieves 1) reduced inductor DC current ( I L ,DC) at small voltage conversion ratios (VCRs), 2) optimized switching and conduction losses, and 3) extended duty ratio range, enabling the use of small-sized inductors with higher DC resistance (DCR) and resulting in a compact system volume. LV switches handle most of the current conduction, reducing switching losses and silicon area for higher on-chip power density. The fabricated converter, using a 180-nm BCD process, generates 0.8-1.8 V output from 12 V/24 V inputs with a 3 A maximum load. Measured results show total I L ,DC of 1.2 A at VCR 0.075 and 2 A load. The converter achieves a peak power density of 355 mW/mm 3 with a power passive volume of 15.2 mm 3 . Peak efficiencies are 85% at 12 V input and 84.2% at 24 V input.
- 11 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (12) , 15109-15114
A 12/24 V-Input HV-LV-Separated Hybrid SC PoL Converter With 355 mW/mm3 Power Density at 3 A Load Current and 15.2 mm3 Power Passives
This letter presents a high-power-density point-of-load (PoL) DC-DC converter for 12/24 V input applications, using the proposed high voltage-low voltage (HV-LV) separated hybrid switched-capacitor (SC) topology. By incorporating inductors between the SC networks in HV/LV domains, the design achieves 1) reduced inductor DC current ( I L ,DC) at small voltage conversion ratios (VCRs), 2) optimized switching and conduction losses, and 3) extended duty ratio range, enabling the use of small-sized inductors with higher DC resistance (DCR) and resulting in a compact system volume. LV switches handle most of the current conduction, reducing switching losses and silicon area for higher on-chip power density. The fabricated converter, using a 180-nm BCD process, generates 0.8-1.8 V output from 12 V/24 V inputs with a 3 A maximum load. Measured results show total I L ,DC of 1.2 A at VCR 0.075 and 2 A load. The converter achieves a peak power density of 355 mW/mm 3 with a power passive volume of 15.2 mm 3 . Peak efficiencies are 85% at 12 V input and 84.2% at 24 V input.
- 12 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 269-272
Modelling and Analysis of ΔΣ-Modulation-Based Output Spectrum Spur Reduction in Dual-Path Hybrid DC-DC Converters
This paper presents a first mathematical model for estimating the output spectrum spurs of dual-path hybrid (DPH) DC-DC converters and proposes a $\Delta\Sigma-$modulation control technique to reduce harmonic spikes. The proposed model is hand-calculation friendly and can ensure reasonable accuracy. It features the prediction of the output spectrum spurs that can compromise the noise characteristic of the converters. We also propose a spur reduction method using a 2–2 MASH $\Delta\Sigma-$modulator to replace the conventional pulse-width modulation control, realizing a $4^{\text{t}\text{h}}$ order noise shaping function for better noise and limit-cycle spike suppression with relaxed stability issue. Simulation results show that the $\Delta\Sigma-$modulation controlled DPH converter achieves a spectrum spike reduction of 17. 6dB and 15.2 dB in low- and high-frequency conditions, respectively, compared with PWM control.- 12 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 269-272
Modelling and Analysis of ΔΣ-Modulation-Based Output Spectrum Spur Reduction in Dual-Path Hybrid DC-DC Converters
This paper presents a first mathematical model for estimating the output spectrum spurs of dual-path hybrid (DPH) DC-DC converters and proposes a $\Delta\Sigma-$modulation control technique to reduce harmonic spikes. The proposed model is hand-calculation friendly and can ensure reasonable accuracy. It features the prediction of the output spectrum spurs that can compromise the noise characteristic of the converters. We also propose a spur reduction method using a 2–2 MASH $\Delta\Sigma-$modulator to replace the conventional pulse-width modulation control, realizing a $4^{\text{t}\text{h}}$ order noise shaping function for better noise and limit-cycle spike suppression with relaxed stability issue. Simulation results show that the $\Delta\Sigma-$modulation controlled DPH converter achieves a spectrum spike reduction of 17. 6dB and 15.2 dB in low- and high-frequency conditions, respectively, compared with PWM control.