Małgorzata Makowska

This study aims to evaluate the effect of adding a chitosan/perlite (Ch/P) carrier to anaerobic digestion (AD) on the efficiency and kinetics of the process, as well as the directional changes in the bacterial microbiome. A carrier with this composition was applied in the AD process for the first time. A laboratory experiment using wafer waste (WF) and cheese (CE) waste was conducted under mesophilic conditions. The analysis of physico-chemical properties confirmed the suitability of the tested carrier material for anaerobic digestion. Both components influenced the microstructural characteristics of the carrier: perlite contributed to the development of specific surface area, while chitosan determined the porosity of the system. Using next-generation sequencing (NGS), the study examined how the additive affected the genetic diversity of bacterial communities. Fourier-transform infrared spectroscopy (FTIR) revealed that the degradation rate depended on both the carrier and the substrate type. Consequently, the presence of the carrier led to an increase in the volume of biogas and methane produced. The volume of methane for the wafer waste (WF–control) increased from 351.72 m³ Mg⁻¹ (VS) to 410.74 m³ Mg⁻¹ (VS), while for the cosubstrate sample (wafer and cheese, WFC–control), it increased from 476.84 m³ Mg⁻¹ (VS) to 588.55 m³ Mg⁻¹ (VS).

This paper describes the process of drying sewage sludge mixtures with the addition of various components: straw chaff, wood sawdust, ash, bark, wood chips, and walnut shells. The tests were conducted in two series: summer and autumn (with maximum insolation of 24.1 and 29.8 MJ∙m⁻², respectively). Using a set of sensors with which the experimental station was equipped, the parameters of the environment (temperature, humidity, and insolation) and the parameters of the dried mixtures (temperature and humidity) were measured. Based on the results obtained, the influence of external factors on the parameters, time, and drying effect of the respective mixtures was analyzed. With the initial moisture content of the mixtures ranging from 41 to 79%, a final moisture content of 6 to 49% was obtained, depending on the components and drying conditions. It was found that the drying rate was most influenced by the amount of solar energy and the associated outdoor (maximum 29 °C and 19 °C) and indoor (maximum 33 °C and 24 °C) air temperatures, and in the second series, there was an additional effect of the temperature of the mixtures (maximum 30 °C), upon which the intensity of water evaporation depended. Straw chaff and walnut shells proved to be the best additives, for which the highest drying rates were obtained (max. 50 to 60% humidity drop). The possibility of using dried materials for agricultural and energy purposes was indicated. This approach is in line with the principles of sustainable development.

One method of preparing sludge for management and use is solar drying. To intensify the drying process, natural lignocellulosic additives can be used to alter the structure of the sludge and accelerate water evaporation. Light, hard materials with low absorption capacity are best suited for this purpose, e.g., walnut shells, which are unused waste. The aim of the study was to determine the impact of the evaluation of walnut shells on the sludge drying process and to assess the impact of the drying process on the chemical, physical, and fuel properties of the additive. The moisture content, crushing strength, chemical composition, and physical and fuel properties of mixtures were determined. A small addition of walnut shells (25%) was found to accelerate the drying process even in winter and spring (up to 30 days) compared to sludge without additives. Walnut shells retain their chemical composition and strength despite unfavourable conditions and a chemically aggressive environment, indicating they may be reused. The mixture containing sewage sludge and walnut shells has a calorific value of 15.6 MJ/kg, which is similar to wood; it is also fully biodegradable and suitable as a fertiliser to improve soil structure, as it contains approx. 80–90% DM (including approx. 40% carbon, 3% nitrogen, and other elements, such as phosphorus and potassium.)

As a by-product of wastewater treatment, sewage sludge can be used for natural, agricultural, or energy purposes. One method of preparing sludge for management and use is solar drying. To intensify the drying process, natural additives can be used to alter the structure of the sludge and accelerate the evaporation of water. This research aimed to evaluate the influences of different organic additives in sewage sludge mixtures on the physicochemical and energy parameters of briquettes. This research was carried out without thermal boosting in a 4 × 2.5 × 2 m plastic tunnel. The tunnel was equipped with three drying stations and control and measuring equipment. In two test series, sludge additives in the form of straw and lignocellulosic materials, sawdust, bark, woodchips, and walnut shells, were used. Briquettes were made from the resulting mixtures and then subjected to physical and chemical analyses. This research showed high variability in the contents of trace elements, nitrogen, and sulphur in relation to an increase in the amount of sludge in the briquettes, which, for the briquettes made from sewage sludge, was nearly twice as high as for the briquettes made from the mixtures. The results of the flue gas analysis for the briquettes with sawdust and wood chip additives were very similar. The briquettes made from sewage sludge with lignocellulosic materials (bark and wood chips) had fuel properties similar to woody biomass, with a calorific value and heat of combustion of 15–16 MJ/kg. Fibrous additives (straw) significantly increased the strength parameters of the briquettes, by more than 50% of the value. The compositions and properties of the mixtures affected the following briquetting parameters: temperature and compressive force. The briquettes made from sewage sludge and additives can be classified according to ISO 21640 as SRFs (solid recovered fuels). In most of the results, the net calorific value (NCV) was 3 to 4; the chlorine content (CL) was 2 to 1; and the mercury content (Hg) was 1. The sewage sludge mixtures facilitated the agricultural and energy use of the briquettes.

The article aims to present the results of research on anaerobic digestion (AD) of waste wafers (WF - control) and co-substrate system - waste wafers and cheese (WFC - control), combined with digested sewage sludge. The aim of the study was to evaluate the physicochemical parameters of the chitosan/perlite (Ch/P; 3:1) carrier material and to verify its effect on the directions of change of the bacterial microbiome, removal kinetics of organic matter and AD process efficiency. The experiment was conducted in a laboratory, in a periodical mode of operation of bioreactors, under mesophilic conditions. The results of analyses of morphological-dispersive, spectroscopic, adsorption, thermal and microbiological properties confirmed that the tested carrier material can be an excellent option to implement in biotechnological processes, especially in anaerobic digestion. The microstructural properties of the carrier were influenced by both components: perlite determined the development of the specific surface area, while chitosan shaped the porosity of the system. The thermal properties were determined by the less heat-resistant component, present in a threefold higher weight proportion, i.e. chitosan. The evaluation of quantitative and qualitative changes in the genetic diversity of bacterial communities, carried out using Next Generation Sequencing (NGS), showed that the material has a modifying effect on the bacterial microbiome. Amount of bacteria from phyla Actinobacteria, Bacteroidetes, Campilobacterota, Chloroflexi, Euryarchaeota, Planctomycetes, and Proteobacteria decreased while Firmicutes, Synergistetes, and Thermotogae increased during the course of the experiment. The shapes of the FT-IR spectra indicated a dependence of the degradation rate on both the presence of the carrier and the cosubstrate system. Monitoring of the course of AD was carried out by measuring key parameters for the stability of the process: pH, VFA and VFA/TA ratio (volatile fatty acids/total alkalinity). As a result, an increase in the volume of biogas/methane produced, under the influence of the carrier, was recorded for WF-control by 12.05% and for WFC-control by 19.16%. The volume of methane for the WF-control increased from 351.72 m3 Mg-1 VS to 411.14 m3 Mg-1 VS, while for the cosubstrate sample it increased from 476.84 m3 Mg-1 VS to 518.08 m3 Mg-1 VS, confirming the validity of combining the respective cosubstrate with microbial carrier in anaerobic bioreactor.

Intensive economic development causes the risk of introducing the so-called emerging contaminants (EC) into the environment. This group of contaminants includes pharmaceuticals, including non-steroidal anti-inflammatory drugs (NSAIDs), the consumption of which is steadily increasing in Poland as...

The increase in the standard of living and economic development of cities and smaller settlement units implies the extension and modernization of infrastructure, including wastewater collection and treatment systems, which is closely related to the protection of surface water and groundwater. This study analyzes the effects of the modernization of two wastewater treatment plants carried out between 2019 and 2020. These are the municipal wastewater treatment plants for Rawicz and Kościan in the Wielkopolska region. The analysis of contamination indicators and wastewater treatment efficiency showed that in both plants, the modernization and extension of wastewater treatment and sludge treatment technologies resulted in improved treated wastewater parameters and better sludge preparation for use. The high efficiency of contaminant removal (mostly above 94%) improves the standard of living, intensifies care for the environment, and increases the attractiveness of the agglomerations served by the analyzed plants. The obtained results were confirmed by statistical tests.