Abdullah Akdoğan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Abdullah Akdoğan has a total of 78 co-authors. Here are the top co-authors by number of shared publications:
- Muath Njjar
Chemical Engineering Department, Pamukkale University
8 shared publications - Canan Onac
Pamukkale University, Faculty of Science, Department of Chemistry and Advanced Technology Application and Research Center, Denizli, Türkiye
4 shared publications - Umit Divrikli
Chemistry Department, Pamukkale University, Denizli, Turkey
4 shared publications - Ahmet Kaya
Chemistry Department, Pamukkale University, Denizli, Turkey
3 shared publications - Ezgi Zekiye Akturk
Chemical Engineering Department, Izmir Institute of Technology
3 shared publications - Mehmet Alperen Ergün
Chemistry Department, Pamukkale University, Denizli, Turkey
3 shared publications
Latest Publications
- 29 June 2026
- Published by Elsevier
- p. 71-88
Carbon nanotubes from waste
- 29 June 2026
- Published by Elsevier
Contributors
- 30 January 2026
- Published by Springer Nature in Chemical Papers
- Vol. 80 (4) , 3895-3909
Sustainable extraction of Sb(III) using a natural deep eutectic solvent: greenness assessment and application to real food and water samples
- 30 January 2026
- Published by Springer Nature in Chemical Papers
- Vol. 80 (4) , 3895-3909
Sustainable extraction of Sb(III) using a natural deep eutectic solvent: greenness assessment and application to real food and water samples
- 29 December 2025
- Published by Celal Bayar University Journal of Science in Celal Bayar Üniversitesi Fen Bilimleri Dergisi
- Vol. 21 (4) , 16-22
Carbon Footprint Calculation: A Case Study from Textile Industry
This study investigates the carbon footprint (CFP) of a textile manufacturing plant located in Denizli province for the year 2021. The analysis employs the Tier Method to estimate greenhouse gas emissions across Scope 1, Scope 2, and Scope 3 categories, utilizing data on energy consumption, waste management, and transportation. The results reveal that Scope 2 emissions, primarily from electricity consumption, constitute the largest portion of the plant’s CFP. In contrast, Scope 1 emissions are mainly driven by diesel and natural gas use, with negligible contributions from gasoline and fire extinguisher leakage. Scope 3 emissions are significantly influenced by wastewater treatment and water supply. The findings underscore the importance of focusing on electricity efficiency and renewable energy sources to mitigate emissions and highlight potential areas for improvement in water management and waste processing. The study provides a baseline for developing targeted strategies to reduce the plant's environmental impact and enhance sustainability practices in the textile industry.
- 29 December 2025
- Published by Celal Bayar University Journal of Science in Celal Bayar Üniversitesi Fen Bilimleri Dergisi
- Vol. 21 (4) , 16-22
Carbon Footprint Calculation: A Case Study from Textile Industry
This study investigates the carbon footprint (CFP) of a textile manufacturing plant located in Denizli province for the year 2021. The analysis employs the Tier Method to estimate greenhouse gas emissions across Scope 1, Scope 2, and Scope 3 categories, utilizing data on energy consumption, waste management, and transportation. The results reveal that Scope 2 emissions, primarily from electricity consumption, constitute the largest portion of the plant’s CFP. In contrast, Scope 1 emissions are mainly driven by diesel and natural gas use, with negligible contributions from gasoline and fire extinguisher leakage. Scope 3 emissions are significantly influenced by wastewater treatment and water supply. The findings underscore the importance of focusing on electricity efficiency and renewable energy sources to mitigate emissions and highlight potential areas for improvement in water management and waste processing. The study provides a baseline for developing targeted strategies to reduce the plant's environmental impact and enhance sustainability practices in the textile industry.
- 25 December 2025
- Published by Akademik Gida in Akademik Gıda
- Vol. 22 (4) , 273-281
Validation of an HPLC-UV Method for Simultaneous Analysis of Ascorbic and Oxalic Acids in Beverages
A reversed-phase high-performance liquid chromatography (RP/HPLC-UV) method was developed for the rapid and simultaneous analysis of ascorbic and oxalic acids in both industrial and freshly squeezed beverages. Due to the rapid degradation of ascorbic acid, its stability was also investigated. The analysis was performed using an Inertsil ODS-3 column with a mobile phase consisting of 0.01 mol L⁻¹ KH₂PO₄ phosphate buffer at pH 2.3. Detection wavelengths were set at 245 nm for ascorbic acid and 205 nm for oxalic acid. The limits of detection (LOD) were 1.4 mg L⁻¹ for ascorbic acid and 1.3 mg L⁻¹ for oxalic acid. After 48 hours of opening an industrial fruit juice package, an 18.5% reduction in ascorbic acid content was found. The method demonstrated within-day repeatability (n = 3) of 4.1% for ascorbic acid and 4.6% for oxalic acid. Between-day precision, expressed as relative standard deviation (RSD), was 3.85% for ascorbic acid and 4.33% for oxalic acid, based on 10 replicates (n= 10). The accuracy of the method was validated with an average recovery rate ranging from 93% to 104%.
- 25 December 2025
- Published by Akademik Gida in Akademik Gıda
- Vol. 22 (4) , 273-281
Validation of an HPLC-UV Method for Simultaneous Analysis of Ascorbic and Oxalic Acids in Beverages
A reversed-phase high-performance liquid chromatography (RP/HPLC-UV) method was developed for the rapid and simultaneous analysis of ascorbic and oxalic acids in both industrial and freshly squeezed beverages. Due to the rapid degradation of ascorbic acid, its stability was also investigated. The analysis was performed using an Inertsil ODS-3 column with a mobile phase consisting of 0.01 mol L⁻¹ KH₂PO₄ phosphate buffer at pH 2.3. Detection wavelengths were set at 245 nm for ascorbic acid and 205 nm for oxalic acid. The limits of detection (LOD) were 1.4 mg L⁻¹ for ascorbic acid and 1.3 mg L⁻¹ for oxalic acid. After 48 hours of opening an industrial fruit juice package, an 18.5% reduction in ascorbic acid content was found. The method demonstrated within-day repeatability (n = 3) of 4.1% for ascorbic acid and 4.6% for oxalic acid. Between-day precision, expressed as relative standard deviation (RSD), was 3.85% for ascorbic acid and 4.33% for oxalic acid, based on 10 replicates (n= 10). The accuracy of the method was validated with an average recovery rate ranging from 93% to 104%.
- 10 July 2025
- Published by Taylor & Francis in Journal of Biomaterials Science, Polymer Edition
- Vol. 37 (4) , 619-649
Nanostructured Ox-MWCNT-PPy-Au electrochemical sensor for ultralow detection of retrorsine and evaluation of its cytotoxic effects on liver cells
This study presents the development of a novel retrorsine (RTS)-imprinted sensor utilizing oxidized multi-walled carbon nanotubes (Ox-MWCNTs), polypyrrole (PPy), and gold nanoparticles (AuNPs), employing square wave voltammetry for the sensitive and selective detection of RTS which causes oxidative-stress and DNA damage. The fabricated Ox-MWCNT-PPy-AuNP sensor demonstrated a surface-area of (0.218 cm2) is 4.25 times larger than a bare glassy carbon electrode, with a low charge transfer resistance (10.9 Ω), enhancing electron transfer kinetics. The sensor showed excellent sensitivity in detecting retrorsine, with a limit of detection of 0.035 nM in synthetic matrices and -0.030 nM in HepaRG cell culture medium. Toxicity assays in HepaRG cells revealed dose-dependent oxidative-stress, with glutathione levels decreasing from 23.08 ± 0.21 µmol/109 to 21.21 ± 0.02 µmol/109 at 35 µM retrorsine. Concurrently, GSSG levels increased from 1.32 ± 0.26 µmol/109 to 2.22 ± 0.02 µmol/109. DNA-damage assessed via comet assay, showed significant increases in tail-moment (2.53 µm) and tail-migration (16.13 µm). Oxidative DNA-damage, indicated by 8-OHdG levels, increased significantly from 0.29 ± 0.02 ng.mL- (control) to 0.47 ± 0.07 ng.mL- at 35 µM retrorsine. These findings demonstrate the sensor's effectiveness for retrorsine detection and its applicability in toxicological studies. The integration of nanomaterial engineering and molecular imprinting provides a highly sensitive, selective, and eco-friendly solution for monitoring toxic agents and assessing their biological impacts.
- 10 July 2025
- Published by Taylor & Francis in Journal of Biomaterials Science, Polymer Edition
- Vol. 37 (4) , 619-649
Nanostructured Ox-MWCNT-PPy-Au electrochemical sensor for ultralow detection of retrorsine and evaluation of its cytotoxic effects on liver cells
This study presents the development of a novel retrorsine (RTS)-imprinted sensor utilizing oxidized multi-walled carbon nanotubes (Ox-MWCNTs), polypyrrole (PPy), and gold nanoparticles (AuNPs), employing square wave voltammetry for the sensitive and selective detection of RTS which causes oxidative-stress and DNA damage. The fabricated Ox-MWCNT-PPy-AuNP sensor demonstrated a surface-area of (0.218 cm2) is 4.25 times larger than a bare glassy carbon electrode, with a low charge transfer resistance (10.9 Ω), enhancing electron transfer kinetics. The sensor showed excellent sensitivity in detecting retrorsine, with a limit of detection of 0.035 nM in synthetic matrices and -0.030 nM in HepaRG cell culture medium. Toxicity assays in HepaRG cells revealed dose-dependent oxidative-stress, with glutathione levels decreasing from 23.08 ± 0.21 µmol/109 to 21.21 ± 0.02 µmol/109 at 35 µM retrorsine. Concurrently, GSSG levels increased from 1.32 ± 0.26 µmol/109 to 2.22 ± 0.02 µmol/109. DNA-damage assessed via comet assay, showed significant increases in tail-moment (2.53 µm) and tail-migration (16.13 µm). Oxidative DNA-damage, indicated by 8-OHdG levels, increased significantly from 0.29 ± 0.02 ng.mL- (control) to 0.47 ± 0.07 ng.mL- at 35 µM retrorsine. These findings demonstrate the sensor's effectiveness for retrorsine detection and its applicability in toxicological studies. The integration of nanomaterial engineering and molecular imprinting provides a highly sensitive, selective, and eco-friendly solution for monitoring toxic agents and assessing their biological impacts.
- 16 June 2025
- Published by Royal Society of Chemistry (RSC) in Analytical Methods
- Vol. 17 (26) , 5508-5518
A novel MIP electrochemical sensor based on a CuFe2O4NPs@rGO nanocomposite and its application in breast milk samples for the determination of fipronil
Background: fipronil, a widely utilized insecticide in agriculture, has been shown to have potential health implications as it can accumulate in the environment and affect human health.
- 16 June 2025
- Published by Royal Society of Chemistry (RSC) in Analytical Methods
- Vol. 17 (26) , 5508-5518
A novel MIP electrochemical sensor based on a CuFe2O4NPs@rGO nanocomposite and its application in breast milk samples for the determination of fipronil
Background: fipronil, a widely utilized insecticide in agriculture, has been shown to have potential health implications as it can accumulate in the environment and affect human health.
- 30 November 2024
- Published by Springer Nature in Journal of Food Measurement and Characterization
- Vol. 19 (1) , 401-411
Determination of Cd in some food and water samples using emulsion liquid-liquid microextraction process with hydrophobic deep eutectic solvent
- 30 November 2024
- Published by Springer Nature in Journal of Food Measurement and Characterization
- Vol. 19 (1) , 401-411
Determination of Cd in some food and water samples using emulsion liquid-liquid microextraction process with hydrophobic deep eutectic solvent