Zuzana Mičicová
Research Subjects
Zuzana Mičicová has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Darina Ondrušová
Alexander Dubček University of Trenčín, Faculty of Industrial Technologies in Púchov, Ivana Krasku 491/30, 020 01 Púchov, Slovakia
8 shared publications - Mariana Pajtášová
Alexander Dubček University of Trenčín
8 shared publications - Petra Skalková
Department of Materials Technologies and Environment, Faculty of Industrial Technologies in Púchov, Alexander Dubček University of Trenčín, I. Krasku 491/30, 020 01 Púchov, Slovakia
7 shared publications - Slavomíra Božeková
Department of Materials Technologies and Environment, Faculty of Industrial Technologies in Púchov, Alexander Dubček University of Trenčín, I. Krasku 491/30, 020 01 Púchov, Slovakia
7 shared publications - Ivan Labaj
Department of Materials Technologies and Environment, Faculty of Industrial Technologies in Púchov, Alexander Dubček University of Trenčín, I. Krasku 491/30, 020 01 Púchov, Slovakia
6 shared publications - Juliána Vršková
Department of Materials Technologies and Environment, Faculty of Industrial Technologies in Púchov, Alexander Dubček University of Trenčín, I. Krasku 491/30, 020 01 Púchov, Slovakia
4 shared publications
Latest Publications
- 7 May 2026
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
Physically treated cellulose and its use in composites
In recent years, various chemical and physical modification methods have been investigated to enhance the interfacial adhesion between cellulose fillers and rubber matrices in composites. Cellulose is of particular interest due to its biodegradability and environmental friendliness, making it a sustainable alternative to conventional fillers. Among physical methods, ultrasound treatment is especially effective. Ultrasonic waves generate cavitation in aqueous solutions, producing strong hydrodynamic forces that disrupt van der Waals interactions between cellulose particles and improve their dispersion. In this study, cellulose was ultrasonically treated in water and subsequently characterized by Fourier transform infrared spectroscopy and thermal analysis to assess structural and thermal changes. The modified cellulose was then used as a filler in rubber composites. The composites are evaluated for their rheological and mechanical properties, and the impact of ultrasound treatment on overall composite performance is determined. The results demonstrate that ultrasonic treatment of cellulose enhances its reinforcing efficiency in rubber composites, leading to improved mechanical strength, higher crosslinking density, and reduced swelling.
- 7 May 2026
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
Physically treated cellulose and its use in composites
In recent years, various chemical and physical modification methods have been investigated to enhance the interfacial adhesion between cellulose fillers and rubber matrices in composites. Cellulose is of particular interest due to its biodegradability and environmental friendliness, making it a sustainable alternative to conventional fillers. Among physical methods, ultrasound treatment is especially effective. Ultrasonic waves generate cavitation in aqueous solutions, producing strong hydrodynamic forces that disrupt van der Waals interactions between cellulose particles and improve their dispersion. In this study, cellulose was ultrasonically treated in water and subsequently characterized by Fourier transform infrared spectroscopy and thermal analysis to assess structural and thermal changes. The modified cellulose was then used as a filler in rubber composites. The composites are evaluated for their rheological and mechanical properties, and the impact of ultrasound treatment on overall composite performance is determined. The results demonstrate that ultrasonic treatment of cellulose enhances its reinforcing efficiency in rubber composites, leading to improved mechanical strength, higher crosslinking density, and reduced swelling.
- Open Access
- 19 December 2025
- Published by LUKASIEWICZ Research Network - Industrial Chemistry Research Institute in Polimery
- Vol. 71 (1) , 26-31
Effect of recycled PP/EPDM on properties of NR-based rubber compounds
Effect of recycled thermoplastic vulcanizate (r-PP/EPDM) on the properties of rubber compounds based on natural rubber (NR) was investigated. Compounds containing various amounts of r-PP/EPDM (0, 27.6, and 55 phr) were analyzed. Parameters such as curing characteristics and crosslinking density were assessed. SEM showed limited compatibility of the blends depending on the amount of r-PP/EPDM, which correlated with reduced crosslinking density and increased swelling degree.
- 19 December 2025
- Published by LUKASIEWICZ Research Network - Industrial Chemistry Research Institute in Polimery
- Vol. 71 (1) , 26-31
Open AccessEffect of recycled PP/EPDM on properties of NR-based rubber compounds
Effect of recycled thermoplastic vulcanizate (r-PP/EPDM) on the properties of rubber compounds based on natural rubber (NR) was investigated. Compounds containing various amounts of r-PP/EPDM (0, 27.6, and 55 phr) were analyzed. Parameters such as curing characteristics and crosslinking density were assessed. SEM showed limited compatibility of the blends depending on the amount of r-PP/EPDM, which correlated with reduced crosslinking density and increased swelling degree.
- Open Access
- 7 November 2025
- Published by LUKASIEWICZ Research Network - Industrial Chemistry Research Institute in Polimery
- Vol. 70 (11-12) , 744-751
The Effect of industrial waste combustion ash on the rubber compounds mixing and vulcanization process
Instead of conventional carbon black (N550), an alternative carbon-based filler (AFC) - ash from the incineration of industrial waste - was used to obtain rubber compounds. The effect of this type of filler on the mixing and vulcanization process of rubber compounds was investigated. The addition of AFC reduced the maximum torque and real temperature of the compound. Compounds with a high AFC content were characterized by greater stiffness in the uncured state and significantly longer scorch times, while maintaining optimal vulcanization times. The obtained results indicate that AFC can partially or completely replace N550 in rubber compounds for conveyor belts without negatively impacting key processing parameters.
- 7 November 2025
- Published by LUKASIEWICZ Research Network - Industrial Chemistry Research Institute in Polimery
- Vol. 70 (11-12) , 744-751
Open AccessThe Effect of industrial waste combustion ash on the rubber compounds mixing and vulcanization process
Instead of conventional carbon black (N550), an alternative carbon-based filler (AFC) - ash from the incineration of industrial waste - was used to obtain rubber compounds. The effect of this type of filler on the mixing and vulcanization process of rubber compounds was investigated. The addition of AFC reduced the maximum torque and real temperature of the compound. Compounds with a high AFC content were characterized by greater stiffness in the uncured state and significantly longer scorch times, while maintaining optimal vulcanization times. The obtained results indicate that AFC can partially or completely replace N550 in rubber compounds for conveyor belts without negatively impacting key processing parameters.
- Open Access
- 7 November 2025
- Published by LUKASIEWICZ Research Network - Industrial Chemistry Research Institute in Polimery
- Vol. 70 (11-12) , 738-743
Mechanical properties of natural rubber composites with walnut shell powder and cellulose
The effect of filler type and quantity (30, 40 phr), i.e., walnut shell powder (WS) and cellulose (CEL), on the tensile properties and hardness of natural rubber was investigated. Additionally, resistance to thermo-oxidative aging and its effect on mechanical properties was assessed. Both WS and CEL significantly improve the mechanical properties of natural rubber, while also providing an environmentally friendly and economical alternative to traditional fillers.
- 7 November 2025
- Published by LUKASIEWICZ Research Network - Industrial Chemistry Research Institute in Polimery
- Vol. 70 (11-12) , 738-743
Open AccessMechanical properties of natural rubber composites with walnut shell powder and cellulose
The effect of filler type and quantity (30, 40 phr), i.e., walnut shell powder (WS) and cellulose (CEL), on the tensile properties and hardness of natural rubber was investigated. Additionally, resistance to thermo-oxidative aging and its effect on mechanical properties was assessed. Both WS and CEL significantly improve the mechanical properties of natural rubber, while also providing an environmentally friendly and economical alternative to traditional fillers.
- Open Access
- 7 November 2025
- Published by LUKASIEWICZ Research Network - Industrial Chemistry Research Institute in Polimery
- Vol. 70 (11-12) , 721-726
Effect of bentonite silanized using microwave radiation on natural rubber properties
Bentonite was modified with silane using microwave irradiation (Milestone flexiWAVE system) and compared with conventionally treated bentonite under identical conditions. The modified bentonite was characterized using Fourier transform infrared spectroscopy, energy dispersive X-ray analysis, and thermogravimetric analysis. The effect of modified bentonite on the rheological and mechanical properties of natural rubber was investigated. The use of microwave radiation to modify bentonite with silane significantly improved the compatibility of the filler with the polymer matrix, which resulted in more effective stress transfer, more uniform filler distribution and improved mechanical properties of the composite.
- 7 November 2025
- Published by LUKASIEWICZ Research Network - Industrial Chemistry Research Institute in Polimery
- Vol. 70 (11-12) , 721-726
Open AccessEffect of bentonite silanized using microwave radiation on natural rubber properties
Bentonite was modified with silane using microwave irradiation (Milestone flexiWAVE system) and compared with conventionally treated bentonite under identical conditions. The modified bentonite was characterized using Fourier transform infrared spectroscopy, energy dispersive X-ray analysis, and thermogravimetric analysis. The effect of modified bentonite on the rheological and mechanical properties of natural rubber was investigated. The use of microwave radiation to modify bentonite with silane significantly improved the compatibility of the filler with the polymer matrix, which resulted in more effective stress transfer, more uniform filler distribution and improved mechanical properties of the composite.
- 10 June 2025
- Published by Springer Nature
- p. 101-114
Bentonite Microwave Modification and Its Impact on Polymer Materials
- 10 June 2025
- Published by Springer Nature
- p. 101-114
Bentonite Microwave Modification and Its Impact on Polymer Materials
- Open Access
- 16 April 2024
- Published by LUKASIEWICZ Research Network - Industrial Chemistry Research Institute in Polimery
- Vol. 69 (4) , 245-253
Atmospheric plasma treatment of rubber and its effect on surface characteristics
The changes of rubber blend surface induced by atmospheric plasma at several conditions were studied via FTIR, SEM, contact angle and adhesion measurement. After plasma, the presence of OH, COO- bands of higher intensity was observed, whilst methylene groups reduced. A several formations of weaker agglomeration and cleaning of the surface was recognized. Also an intense decline of contact angles was observed. The plasma induced significantly greater changes at the 0.5 mm position, whereas emission times of 10 s and 30 s did not significantly affect the modifications of the investigated surface.
- 16 April 2024
- Published by LUKASIEWICZ Research Network - Industrial Chemistry Research Institute in Polimery
- Vol. 69 (4) , 245-253
Open AccessAtmospheric plasma treatment of rubber and its effect on surface characteristics
The changes of rubber blend surface induced by atmospheric plasma at several conditions were studied via FTIR, SEM, contact angle and adhesion measurement. After plasma, the presence of OH, COO- bands of higher intensity was observed, whilst methylene groups reduced. A several formations of weaker agglomeration and cleaning of the surface was recognized. Also an intense decline of contact angles was observed. The plasma induced significantly greater changes at the 0.5 mm position, whereas emission times of 10 s and 30 s did not significantly affect the modifications of the investigated surface.
- Open Access
- 16 April 2024
- Published by LUKASIEWICZ Research Network - Industrial Chemistry Research Institute in Polimery
- Vol. 69 (4) , 254-263
Effect of kaolinite modified with Co(II), Cu(II) and Ni(II) salts on selected properties of tread rubber blend
Effect of kaolinite modified with Cu(II), Co(II) and Ni(II) salts as a partial replacement for carbon black (1 and 8 phr) on the properties of the model tread rubber blend was examined. The blends were prepared in a two-stage process in a Brabender mixer at temperatures of 120°C and 100°C, respectively, with a constant mixing speed of 50 rpm. FT-IR confirmed the formation of copper hydroxyacetate monohydrate complex, which may indicate chemical interactions between rubber components and modified kaolinite. The filler improved technological parameters, tensile properties and hardness. Resistance to thermal aging has also increased.
- 16 April 2024
- Published by LUKASIEWICZ Research Network - Industrial Chemistry Research Institute in Polimery
- Vol. 69 (4) , 254-263
Open AccessEffect of kaolinite modified with Co(II), Cu(II) and Ni(II) salts on selected properties of tread rubber blend
Effect of kaolinite modified with Cu(II), Co(II) and Ni(II) salts as a partial replacement for carbon black (1 and 8 phr) on the properties of the model tread rubber blend was examined. The blends were prepared in a two-stage process in a Brabender mixer at temperatures of 120°C and 100°C, respectively, with a constant mixing speed of 50 rpm. FT-IR confirmed the formation of copper hydroxyacetate monohydrate complex, which may indicate chemical interactions between rubber components and modified kaolinite. The filler improved technological parameters, tensile properties and hardness. Resistance to thermal aging has also increased.
- Open Access
- 27 November 2023
- Published by LUKASIEWICZ Research Network - Industrial Chemistry Research Institute in Polimery
- Vol. 68 (11-12) , 625-630
Effect of low-temperature plasma-treated bentonite on rubber compounds properties
The influence of low-temperature plasma modification of bentonite on the dynamic-mechanical properties and vulcanization of rubber mixtures was examined. EDX, FTIR and TGA analysis were used to evaluate the filler. IR spectra of modified bentonite indicate lower intensity of the bands associated with OH groups and water. TGA confirms a smaller weight loss of samples subjected to plasma treatment, which also proves a lower water content in the mineral, confirming the effectiveness of the plasma treatment used.
- 27 November 2023
- Published by LUKASIEWICZ Research Network - Industrial Chemistry Research Institute in Polimery
- Vol. 68 (11-12) , 625-630
Open AccessEffect of low-temperature plasma-treated bentonite on rubber compounds properties
The influence of low-temperature plasma modification of bentonite on the dynamic-mechanical properties and vulcanization of rubber mixtures was examined. EDX, FTIR and TGA analysis were used to evaluate the filler. IR spectra of modified bentonite indicate lower intensity of the bands associated with OH groups and water. TGA confirms a smaller weight loss of samples subjected to plasma treatment, which also proves a lower water content in the mineral, confirming the effectiveness of the plasma treatment used.
- Open Access
- 27 November 2023
- Published by LUKASIEWICZ Research Network - Industrial Chemistry Research Institute in Polimery
- Vol. 68 (11-12) , 585-592
Effect of alternative carbon-based filler on rubber compounds properties
Instead of conventional carbon black, an alternative carbon filler (ACB) obtained in the pyrolysis process from tire waste was used for rubber compounds. The fillers were characterized using FTIR and TGA methods. The mechanical properties of the obtained rubber compounds and the influence of the fillers used on the vulcanization process, as well as the Payne effect, were examined. The results confirm the possibility of replacing conventional carbon black with an alternative carbon filler in rubber compounds.
- 27 November 2023
- Published by LUKASIEWICZ Research Network - Industrial Chemistry Research Institute in Polimery
- Vol. 68 (11-12) , 585-592
Open AccessEffect of alternative carbon-based filler on rubber compounds properties
Instead of conventional carbon black, an alternative carbon filler (ACB) obtained in the pyrolysis process from tire waste was used for rubber compounds. The fillers were characterized using FTIR and TGA methods. The mechanical properties of the obtained rubber compounds and the influence of the fillers used on the vulcanization process, as well as the Payne effect, were examined. The results confirm the possibility of replacing conventional carbon black with an alternative carbon filler in rubber compounds.