Sahiril-Fernanda Rodríguez-Fuentes
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sahiril-Fernanda Rodríguez-Fuentes has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Margarita Tecpoyotl-Torres
Universidad Autónoma del Estado de Morelos
4 shared publications - Alonso Corona-Chavez
Department of Electronics, Instituto Nacional de Astrofsica, ptica y Electrnica (INAOE), Puebla, Mexico
2 shared publications - Andres-Fernando Plata-Galvis
Department of Electronics, Instituto Nacional de Astrofsica, ptica y Electrnica (INAOE), Puebla, Mexico
2 shared publications - Jose-Luis Olvera-Cervantes
Electronics Department, National Institute of Astrophysics, Optics and Electronics, Puebla, Mexico
2 shared publications - Carlos Andrés Ferrara-Bello
Posgrado en Ingeniería y Ciencias Aplicadas Centro de Investigación en Ingeniería y Ciencias Aplicadas, CIICAp-IICBA,Morelos,MX
1 shared publication - Fernando Rodriguez-Morales
Center for Remote Sensing and Integrated Systems (CReSIS) University of Kansas Lawrence KS USA
1 shared publication
Latest Publications
- 13 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Comparison of Simulated Double Layer Microgrippers with Different Materials
This work presents the analysis of a normally open, electrothermally actuated double-layer microgripper using a chevron device. A Silicon-On-Insulator (SOI) wafer is used for its implementation, consequently the structural layer is made of silicon, in this case, with a thickness of 70 μm, The materials used to implement the upper layers of the double-layer microgrippers are silicon nitride (Si3N4) and polysilicon (Poly-Si), with three different thicknesses: 1, 2 and 5 μm, The highest values of displacement and reaction force, determined at the tips, considering both single- and double-layer microgrippers, correspond to the double-layer gripper, designed with the upper layer of polysilicon of 5 μm.
- 13 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Comparison of Simulated Double Layer Microgrippers with Different Materials
This work presents the analysis of a normally open, electrothermally actuated double-layer microgripper using a chevron device. A Silicon-On-Insulator (SOI) wafer is used for its implementation, consequently the structural layer is made of silicon, in this case, with a thickness of 70 μm, The materials used to implement the upper layers of the double-layer microgrippers are silicon nitride (Si3N4) and polysilicon (Poly-Si), with three different thicknesses: 1, 2 and 5 μm, The highest values of displacement and reaction force, determined at the tips, considering both single- and double-layer microgrippers, correspond to the double-layer gripper, designed with the upper layer of polysilicon of 5 μm.
- 9 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-8
Measurements of S -Parameters in the Free-Space Using a Virtual Reflect
This work introduces a method to measure S-parameters in free space using a Virtual Reflect (VR) generated from a symmetric single-ended Thru measurement. Time-domain analysis shows that the VR accurately replicates the behavior of a physical Reflect. The calibration process was experimentally validated using two approaches, the first involved analyzing the Thru configuration, and the second consisted of measuring the scattering parameters of six Material Under Test (MUTs), showing strong correlation with those derived from the conventional TRL method. Specifically, coefficients of determination (R2) exceeding 0.9203 were achieved for both magnitude and phase, while the Root Mean Square Error (RMSE) reached maximum values of 2.2686 dB and 5.4644° for magnitude and phase, respectively. The proposed method eliminates the need for a metal plate as a physical Reflect standard, reducing errors and simplifying measurements. It also requires fewer standards, shortens measurement time, and is less sensitive to antenna misalignments. An open-source software tool is provided as well.
- 9 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-8
Measurements of S -Parameters in the Free-Space Using a Virtual Reflect
This work introduces a method to measure S-parameters in free space using a Virtual Reflect (VR) generated from a symmetric single-ended Thru measurement. Time-domain analysis shows that the VR accurately replicates the behavior of a physical Reflect. The calibration process was experimentally validated using two approaches, the first involved analyzing the Thru configuration, and the second consisted of measuring the scattering parameters of six Material Under Test (MUTs), showing strong correlation with those derived from the conventional TRL method. Specifically, coefficients of determination (R2) exceeding 0.9203 were achieved for both magnitude and phase, while the Root Mean Square Error (RMSE) reached maximum values of 2.2686 dB and 5.4644° for magnitude and phase, respectively. The proposed method eliminates the need for a metal plate as a physical Reflect standard, reducing errors and simplifying measurements. It also requires fewer standards, shortens measurement time, and is less sensitive to antenna misalignments. An open-source software tool is provided as well.
- 29 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (22) , 41265-41273
UWB Microwave Frequency-Stepped Continuous Wave Sensor for Dual Virtual-Gate Detection of Metallic Objects
This work presents a sensor system based on frequency-stepped continuous wave (SFCW) signals for the detection of metallic objects within dual virtual gates of tunable width. These gates are formed by an electric wall generated through system symmetry and differential-mode signaling. The performance of this variable electric wall was evaluated in three scenarios with different gate widths. In all cases, a coefficient of determination greater than 0.9922 was obtained when compared to a physical barrier formed by a metallic body, thereby confirming the equivalence of their behavior. Additionally, the work includes a step-by-step methodology for metal object detection, which is experimentally validated with the system operating in ultra-wideband (UWB) with signals from 2.5 to 4.5 GHz. From repeated measurements and an ANOVA analysis, a p-value of 0.9988 was obtained, which exceeds the 0.05 significance level, demonstrating the repeatability of the experiments in different conditions. Furthermore, the displacement resolution, average sensitivity, and precision were also evaluated, yielding results of 10 mm, 29.90 cm/ns, and 4.97×10−4 ns, respectively.
- 29 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (22) , 41265-41273
UWB Microwave Frequency-Stepped Continuous Wave Sensor for Dual Virtual-Gate Detection of Metallic Objects
This work presents a sensor system based on frequency-stepped continuous wave (SFCW) signals for the detection of metallic objects within dual virtual gates of tunable width. These gates are formed by an electric wall generated through system symmetry and differential-mode signaling. The performance of this variable electric wall was evaluated in three scenarios with different gate widths. In all cases, a coefficient of determination greater than 0.9922 was obtained when compared to a physical barrier formed by a metallic body, thereby confirming the equivalence of their behavior. Additionally, the work includes a step-by-step methodology for metal object detection, which is experimentally validated with the system operating in ultra-wideband (UWB) with signals from 2.5 to 4.5 GHz. From repeated measurements and an ANOVA analysis, a p-value of 0.9988 was obtained, which exceeds the 0.05 significance level, demonstrating the repeatability of the experiments in different conditions. Furthermore, the displacement resolution, average sensitivity, and precision were also evaluated, yielding results of 10 mm, 29.90 cm/ns, and 4.97×10−4 ns, respectively.
- 1 February 2024
- Published by Universidad Autónoma del Estado de Morelos in Programación matemática y software
- Vol. 16 (1)
Novedoso Cosechador de Energía de Bajo Costo Basado en un Arreglo de Actuadores Piezoeléctricos
En este artículo se presenta el diseño, modelado, fabricación y pruebas de un cosechador de energía proveniente de vibraciones mecánicas, basado en un material piezoeléctrico. Este dispositivo trabaja bajo el principio de transducción piezoeléctrica, es decir que, al deformarse mecánicamente, debido a las vibraciones genera energía eléctrica. El material piezoeléctrico usado en la fabricación fue Zirconato Titanato de Plomo (PZT), y latón como base estructural. Además, se realizaron modelos de elemento finito para predecir la frecuencia del primer modo de vibración del dispositivo, y arreglos experimentales para su validación. La frecuencia de resonancia del modelo numérico y la obtenida experimentalmente (19 Hz) muestran una desviación de 5.03% respectivamente. La potencia generada es de 0.202 mW suficiente para alimentar dispositivos de bajo consumo, tales como calculadoras básicas, relojes de pulsera y transistores, entre otros.
- 1 February 2024
- Published by Universidad Autónoma del Estado de Morelos in Programación matemática y software
- Vol. 16 (1)
Novedoso Cosechador de Energía de Bajo Costo Basado en un Arreglo de Actuadores Piezoeléctricos
En este artículo se presenta el diseño, modelado, fabricación y pruebas de un cosechador de energía proveniente de vibraciones mecánicas, basado en un material piezoeléctrico. Este dispositivo trabaja bajo el principio de transducción piezoeléctrica, es decir que, al deformarse mecánicamente, debido a las vibraciones genera energía eléctrica. El material piezoeléctrico usado en la fabricación fue Zirconato Titanato de Plomo (PZT), y latón como base estructural. Además, se realizaron modelos de elemento finito para predecir la frecuencia del primer modo de vibración del dispositivo, y arreglos experimentales para su validación. La frecuencia de resonancia del modelo numérico y la obtenida experimentalmente (19 Hz) muestran una desviación de 5.03% respectivamente. La potencia generada es de 0.202 mW suficiente para alimentar dispositivos de bajo consumo, tales como calculadoras básicas, relojes de pulsera y transistores, entre otros.