Yuki Emori
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yuki Emori has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Hiroshi Miyazaki
Kyushu University, Fukuoka, Japan
5 shared publications - Hiromasa Sasa
Kyushu University, Fukuoka, Japan
3 shared publications - Masataka Iwakuma
Kyushu University, Fukuoka, Japan
3 shared publications - Gen Nishijima
National Institute for Materials Science (NIMS), Tsukuba, Japan
2 shared publications - Koji Kamiya
National Institute for Materials Science, Tsukuba, Japan
2 shared publications - Kyohei Natsume
National Institute for Materials Science, Tsukuba, Japan
2 shared publications
Latest Publications
- 19 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-6
Design of Shortened REBa 2 Cu 3 O 7-δ Saddle-Shaped Field Coil Ends for Fully Superconducting Synchronous Motors Using Generalized Flatwise Curvature
To reduce carbon dioxide emissions from aircraft, superconducting electric propulsion systems are attracting attention. For aircraft, high power density is particularly important, and increasing the power density requires higher rotational speed. Therefore, we are studying a saddle-shaped field coil made with REBa2Cu3O7-δ (REBCO) tape. This coil can be fixed directly to the shaft, which helps provide the mechanical strength needed for high-speed rotation. However, because of the shape characteristics of the REBCO tape, the coil ends tend to become long, increasing the axial length of the motor. In addition, excessive bending or twisting can damage the tape; thus, careful design is necessary. In this study, we developed a design method to shorten the saddle-shaped field coil and evaluated its electromagnetic performance. We introduced a generalized flatwise curvature to represent bending and twisting and set the allowable curvature of the REBCO tape to 0.1 mm-1 based on its mechanical limits. Using this condition, we designed two types of shortened coils. Model A arranges the coils based on the curvature of the innermost coil, while Model B equalizes the curvature of all coils to prevent interference at the coil ends. Three-dimensional finite-element analysis revealed that the axial gap flux density distribution of both models is almost the same. However, Model B has a slightly larger high-flux-density region because its straight part is longer, resulting in better output performance. The obtained torque also exhibits a strong proportional relationship with the axial integral of the gap flux density, confirming that the coil ends are important regions that contribute to motor output.
- 19 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-6
Design of Shortened REBa 2 Cu 3 O 7-δ Saddle-Shaped Field Coil Ends for Fully Superconducting Synchronous Motors Using Generalized Flatwise Curvature
To reduce carbon dioxide emissions from aircraft, superconducting electric propulsion systems are attracting attention. For aircraft, high power density is particularly important, and increasing the power density requires higher rotational speed. Therefore, we are studying a saddle-shaped field coil made with REBa2Cu3O7-δ (REBCO) tape. This coil can be fixed directly to the shaft, which helps provide the mechanical strength needed for high-speed rotation. However, because of the shape characteristics of the REBCO tape, the coil ends tend to become long, increasing the axial length of the motor. In addition, excessive bending or twisting can damage the tape; thus, careful design is necessary. In this study, we developed a design method to shorten the saddle-shaped field coil and evaluated its electromagnetic performance. We introduced a generalized flatwise curvature to represent bending and twisting and set the allowable curvature of the REBCO tape to 0.1 mm-1 based on its mechanical limits. Using this condition, we designed two types of shortened coils. Model A arranges the coils based on the curvature of the innermost coil, while Model B equalizes the curvature of all coils to prevent interference at the coil ends. Three-dimensional finite-element analysis revealed that the axial gap flux density distribution of both models is almost the same. However, Model B has a slightly larger high-flux-density region because its straight part is longer, resulting in better output performance. The obtained torque also exhibits a strong proportional relationship with the axial integral of the gap flux density, confirming that the coil ends are important regions that contribute to motor output.
- 19 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Performance Testing of 400 kW-Rated REBCO Superconducting Synchronous Machine in Low-Temperature and Low-Pressure Environments
Aircraft equipment needs to maintain stable operation in low-temperature and low-pressure environments. This study assesses the feasibility of operating a developed machine under such conditions. Rotational tests were conducted in an environment that simulated the conditions required for aircraft-mounted equipment. The synchronous machine was installed in a thermostatic chamber that was set to a temperature of −55 °C and pressure of 11 kPa, which mimics the conditions at an altitude of 15,000 m. The machine demonstrated stable operation at a rotational speed of 180 rpm, with a field current of 50 A and an armature current amplitude of 100 A at a frequency of 3 Hz. The synchronous machine was tested in generator mode at ground level under no-load and three-phase short-circuit conditions to evaluate its rated operation under a normal environment. In the no-load test, the field current and rotational speed were increased from 10 A to 110 A and 100 rpm to 2,500 rpm, respectively, and the maximum line voltage was 590 V. In the three-phase short-circuit test, the U, V, and W phases exhibited maximum short-circuit currents of 490 A with a field current of 45 A and rotational speed of 100 rpm. These results confirm that the synchronous machine operated stably at 2,500 rpm with an output of 250 kW in generator mode. The stable performance of the machine under these conditions suggests its potential for enhancing the efficiency, power density, and reliability of electric propulsion systems in aviation.
- 19 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Performance Testing of 400 kW-Rated REBCO Superconducting Synchronous Machine in Low-Temperature and Low-Pressure Environments
Aircraft equipment needs to maintain stable operation in low-temperature and low-pressure environments. This study assesses the feasibility of operating a developed machine under such conditions. Rotational tests were conducted in an environment that simulated the conditions required for aircraft-mounted equipment. The synchronous machine was installed in a thermostatic chamber that was set to a temperature of −55 °C and pressure of 11 kPa, which mimics the conditions at an altitude of 15,000 m. The machine demonstrated stable operation at a rotational speed of 180 rpm, with a field current of 50 A and an armature current amplitude of 100 A at a frequency of 3 Hz. The synchronous machine was tested in generator mode at ground level under no-load and three-phase short-circuit conditions to evaluate its rated operation under a normal environment. In the no-load test, the field current and rotational speed were increased from 10 A to 110 A and 100 rpm to 2,500 rpm, respectively, and the maximum line voltage was 590 V. In the three-phase short-circuit test, the U, V, and W phases exhibited maximum short-circuit currents of 490 A with a field current of 45 A and rotational speed of 100 rpm. These results confirm that the synchronous machine operated stably at 2,500 rpm with an output of 250 kW in generator mode. The stable performance of the machine under these conditions suggests its potential for enhancing the efficiency, power density, and reliability of electric propulsion systems in aviation.
- 9 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Electromagnetic Analysis Evaluation of Split NbTi Superconducting Magnet for Scaled-Up Active Magnetic Regenerative Refrigeration System
Active magnetic regenerative (AMR) refrigeration is expected to be used for hydrogen liquefaction owing to its wide operating temperature range. In a previous study, a reciprocating type of AMR refrigerator (Prototype 1) was used to demonstrate hydrogen liquefaction. In this study, a scaled-up version (Prototype 2) was developed to increase the amount of liquefied hydrogen. For Prototype 2, the main coils were split into two parts to extend the range of the 5 T magnetic field applied to the larger AMR beds filled with magnetic particles. As in Prototype 1, the arrangement of the AMR beds in series helped reduce the axial magnetic forces that hinder the reciprocating motion of the AMR beds and induced voltages in the superconducting magnet. To reduce AC losses, the filament radius of the NbTi superconducting wire used (in Prototype 2) was 10 µm, in contrast to the 30 µm wire used in Prototype 1. By improving the electrical design, the scaled-up magnetic refrigeration system can operate without any electromagnetic problems, such as magnetic forces, induced voltages, and AC losses.
- 9 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Electromagnetic Analysis Evaluation of Split NbTi Superconducting Magnet for Scaled-Up Active Magnetic Regenerative Refrigeration System
Active magnetic regenerative (AMR) refrigeration is expected to be used for hydrogen liquefaction owing to its wide operating temperature range. In a previous study, a reciprocating type of AMR refrigerator (Prototype 1) was used to demonstrate hydrogen liquefaction. In this study, a scaled-up version (Prototype 2) was developed to increase the amount of liquefied hydrogen. For Prototype 2, the main coils were split into two parts to extend the range of the 5 T magnetic field applied to the larger AMR beds filled with magnetic particles. As in Prototype 1, the arrangement of the AMR beds in series helped reduce the axial magnetic forces that hinder the reciprocating motion of the AMR beds and induced voltages in the superconducting magnet. To reduce AC losses, the filament radius of the NbTi superconducting wire used (in Prototype 2) was 10 µm, in contrast to the 30 µm wire used in Prototype 1. By improving the electrical design, the scaled-up magnetic refrigeration system can operate without any electromagnetic problems, such as magnetic forces, induced voltages, and AC losses.
- 2 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Effects of Moving Magnetic Materials in and out of Superconducting Magnet for Active Magnetic Regenerative Refrigeration System
A reciprocating type active magnetic regenerative refrigeration (AMR) utilizes the magnetocaloric effect of magnetic materials which occurs during magnetization and demagnetization processes by moving magnetic materials in and out of a magnet. Estimating the induced voltage and electromagnetic force in the superconducting magnet during the reciprocation is crucial to optimize the design of the AMR system. This paper represents the behavior of the superconducting magnet during the AMR operation that the magnetic material HoAl 2 weighing 250 g enters and exits the 120 mm bore NbTi superconducting coil. The calculation and measurement results of the induced voltage and electromagnetic force in the magnetic field of 0–5 T at 25 K were reported.
- 2 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Effects of Moving Magnetic Materials in and out of Superconducting Magnet for Active Magnetic Regenerative Refrigeration System
A reciprocating type active magnetic regenerative refrigeration (AMR) utilizes the magnetocaloric effect of magnetic materials which occurs during magnetization and demagnetization processes by moving magnetic materials in and out of a magnet. Estimating the induced voltage and electromagnetic force in the superconducting magnet during the reciprocation is crucial to optimize the design of the AMR system. This paper represents the behavior of the superconducting magnet during the AMR operation that the magnetic material HoAl 2 weighing 250 g enters and exits the 120 mm bore NbTi superconducting coil. The calculation and measurement results of the induced voltage and electromagnetic force in the magnetic field of 0–5 T at 25 K were reported.
- 24 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Electromagnetic Design of a REBCO Four-Pole Full-Pitched Armature Coil Composed of Trapezoidal Windings for Fully Superconducting Synchronous Motors
An electric propulsion system is one of the solutions to achieve low carbon dioxide emissions from aircraft. In this regard, a superconducting motor is being developed to achieve higher power density than conventional motors. Because a REBa 2 Cu 3 O 7-σ (REBCO) wire is difficult to bend freely owing to its tape shape, racetrack windings are often used for the armature coils of the superconducting motors. Although the output power can be increased for the same armature current by widening the armature winding pitch angle, the racetrack armature has only a small pitch of 30°. A full-pitched armature with the maximum pitch angle has not been realized in past studies. Therefore, in this study, we propose an unprecedented configuration method of a four-pole full-pitched armature coil composed of trapezoidal windings. To investigate the advantages of the armature, we made a 2D cross-sectional model and determined torque using the finite element method of electromagnetic field analysis. Consequently, we verified that the trapezoidal four-pole armature had lower torque ripple and higher power density than the conventional two-pole racetrack armature. This study confirmed that the proposed novel armature had better characteristics than conventional ones. The armature can make the motor lightweight and low-noise.
- 24 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Electromagnetic Design of a REBCO Four-Pole Full-Pitched Armature Coil Composed of Trapezoidal Windings for Fully Superconducting Synchronous Motors
An electric propulsion system is one of the solutions to achieve low carbon dioxide emissions from aircraft. In this regard, a superconducting motor is being developed to achieve higher power density than conventional motors. Because a REBa 2 Cu 3 O 7-σ (REBCO) wire is difficult to bend freely owing to its tape shape, racetrack windings are often used for the armature coils of the superconducting motors. Although the output power can be increased for the same armature current by widening the armature winding pitch angle, the racetrack armature has only a small pitch of 30°. A full-pitched armature with the maximum pitch angle has not been realized in past studies. Therefore, in this study, we propose an unprecedented configuration method of a four-pole full-pitched armature coil composed of trapezoidal windings. To investigate the advantages of the armature, we made a 2D cross-sectional model and determined torque using the finite element method of electromagnetic field analysis. Consequently, we verified that the trapezoidal four-pole armature had lower torque ripple and higher power density than the conventional two-pole racetrack armature. This study confirmed that the proposed novel armature had better characteristics than conventional ones. The armature can make the motor lightweight and low-noise.