Haolin Han
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Haolin Han has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Shubin Liu
Xidian University
8 shared publications - Zhangming Zhu
Xidian University
6 shared publications - Hongzhi Liang
Xidian University
5 shared publications - Yi Shen
Xidian University
5 shared publications Shubin Liu
4 shared publications- Dengquan Li
Xidian University
3 shared publications
Latest Publications
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 73 (9) , 913-917
A 112 GS/s 7 b 64× Time-Interleaved Hybrid ADC Achieving 43.1-dB SFDR at 44.1-GHz Input in 28-nm CMOS
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 73 (9) , 913-917
A 112 GS/s 7 b 64× Time-Interleaved Hybrid ADC Achieving 43.1-dB SFDR at 44.1-GHz Input in 28-nm CMOS
- 17 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP (00189200) , 1-11
A 16× Interleaved 32-GS/s 8b Hybrid ADC With Self-Tracking Inter-Stage Gain Achieving 44.3-dB SFDR at 20.9-GHz Input
This article presents a 32-GS/s 16-channel hierarchical time-interleaved (TI) hybrid analog-to-digital converter (ADC). The prototype utilizes the intrinsic high-speed quantization of time-domain (TD) ADC to reduce the interleaving factor. By incorporating hierarchical sampling and a cascode sampler, the compact TI-ADC achieves 44.3-dB spurious-free dynamic range (SFDR) at 20.9-GHz input. The sub-ADC adopts a two-stage hybrid-domain architecture that combines a 3-bit successive approximation register (SAR) ADC with a 6-bit inverter-based opposite phase propagation (OPP) time-to-digital converter (TDC). Aprototype chip is fabricated in a 28-nm CMOS process, occupying a core area of 0.141mm2. At 32GS/s, it achieves a signal-to-noise and distortion ratio (SNDR) of 36dB with a Nyquist input while consuming 142.3mW, corresponding to a Walden figure-of-merit of 86.3fJ/conv-step. Meanwhile, a delay-locked loop (DLL)-based calibration loop is proposed to calibrate the full-scale quantization range variation introduced by PVT variations, together with an analog self-tracking inter-stage gain calibration loop. The measured SNDR varies by 1.84dB over a temperature range of $0~{^{\circ } }$ C to $100~{^{\circ } }$ C and fluctuates by 2.25dB with a ±10% supply variation.
- 17 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP (00189200) , 1-11
A 16× Interleaved 32-GS/s 8b Hybrid ADC With Self-Tracking Inter-Stage Gain Achieving 44.3-dB SFDR at 20.9-GHz Input
This article presents a 32-GS/s 16-channel hierarchical time-interleaved (TI) hybrid analog-to-digital converter (ADC). The prototype utilizes the intrinsic high-speed quantization of time-domain (TD) ADC to reduce the interleaving factor. By incorporating hierarchical sampling and a cascode sampler, the compact TI-ADC achieves 44.3-dB spurious-free dynamic range (SFDR) at 20.9-GHz input. The sub-ADC adopts a two-stage hybrid-domain architecture that combines a 3-bit successive approximation register (SAR) ADC with a 6-bit inverter-based opposite phase propagation (OPP) time-to-digital converter (TDC). Aprototype chip is fabricated in a 28-nm CMOS process, occupying a core area of 0.141mm2. At 32GS/s, it achieves a signal-to-noise and distortion ratio (SNDR) of 36dB with a Nyquist input while consuming 142.3mW, corresponding to a Walden figure-of-merit of 86.3fJ/conv-step. Meanwhile, a delay-locked loop (DLL)-based calibration loop is proposed to calibrate the full-scale quantization range variation introduced by PVT variations, together with an analog self-tracking inter-stage gain calibration loop. The measured SNDR varies by 1.84dB over a temperature range of $0~{^{\circ } }$ C to $100~{^{\circ } }$ C and fluctuates by 2.25dB with a ±10% supply variation.
- 17 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. PP (15498328) , 1-10
A 65.5-dB SNDR 100-MS/s Pipelined-SAR ADC With Nested Negative-C and Dynamic Auto-Zeroing Residue Amplifier Achieving $\le$2.2-dB ΔSNDR Over −20 °C to 125 °C
This paper demonstrates a 12-bit 100-MS/s PVT-stabilized pipelined-SAR ADC with fully integrated on-chip calibration. Two key innovations facilitate over 65-dB SNDR with less than 2.2-dB variation from -20 °C to 125 °C: First, a PVT-stabilized nested negative-C topology boosts open-loop gain ( $G_{ol}$ ) of the residue amplifier (RA) by 28 dB, enabling one-time foreground calibration that avoids persistent inter-stage gain error tracking. Second, a dynamic auto-zeroing technique addresses offsets from both the RA and first-stage comparator through a switched-capacitor filter that extracts offsets based on the stochastic characteristics of residue signals. Dynamically level-shifted capacitors (DLSC) are embedded at the differential inputs to neutralize aliased noise and thermal noise, so that the offset drifts under high-temperature environment are effectively cancelled. Fabricated in 40-nm CMOS, the prototype occupies 0.22 mm2 and achieves 65.5-dB SNDR and 83-dB SFDR at Nyquist input while consuming 3.7 mW. Across six tested chips, the prototype design exhibits merely 2.2-dB SNDR degradation over -20 °C ~ 125 °C and 1.3-dB variation under ± 5 % supply voltage (1.1 V) fluctuations.
- 17 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. PP (15498328) , 1-10
A 65.5-dB SNDR 100-MS/s Pipelined-SAR ADC With Nested Negative-C and Dynamic Auto-Zeroing Residue Amplifier Achieving $\le$2.2-dB ΔSNDR Over −20 °C to 125 °C
This paper demonstrates a 12-bit 100-MS/s PVT-stabilized pipelined-SAR ADC with fully integrated on-chip calibration. Two key innovations facilitate over 65-dB SNDR with less than 2.2-dB variation from -20 °C to 125 °C: First, a PVT-stabilized nested negative-C topology boosts open-loop gain ( $G_{ol}$ ) of the residue amplifier (RA) by 28 dB, enabling one-time foreground calibration that avoids persistent inter-stage gain error tracking. Second, a dynamic auto-zeroing technique addresses offsets from both the RA and first-stage comparator through a switched-capacitor filter that extracts offsets based on the stochastic characteristics of residue signals. Dynamically level-shifted capacitors (DLSC) are embedded at the differential inputs to neutralize aliased noise and thermal noise, so that the offset drifts under high-temperature environment are effectively cancelled. Fabricated in 40-nm CMOS, the prototype occupies 0.22 mm2 and achieves 65.5-dB SNDR and 83-dB SFDR at Nyquist input while consuming 3.7 mW. Across six tested chips, the prototype design exhibits merely 2.2-dB SNDR degradation over -20 °C ~ 125 °C and 1.3-dB variation under ± 5 % supply voltage (1.1 V) fluctuations.
- 5 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 73 (1) , 3-7
Offset-Immune Split-LSB Weight Calibration for Capacitor Mismatch and Gain Nonlinearity in Pipelined SAR ADC
This paper presents a digital background calibration technique that uses a split-least-significant-bit (Split-LSB) weight to simultaneously address both capacitor mismatch and gain nonlinearity in pipelined successive approximation register analog-to-digital converters (SAR ADCs). The key innovation of this approach lies in the use of sub-LSB weights, derived from splitting the LSB capacitor, to detect and correct nonlinearity. By integrating 1-bit dynamic element matching (DEM) with a separate-averaging algorithm, this technique achieves the first offset-immune background calibration capable of calibrating both error sources simultaneously. Behavioral simulations of a 14-bit pipelined SAR ADC show significant performance improvements: the signal-to-noise-and-distortion ratio (SNDR) increases from 52.4 dB to 84.2 dB, and the spurious-free dynamic range (SFDR) rises from 56.3 dB to 104.5 dB. These results validate the effectiveness of the proposed technique.
- 5 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 73 (1) , 3-7
Offset-Immune Split-LSB Weight Calibration for Capacitor Mismatch and Gain Nonlinearity in Pipelined SAR ADC
This paper presents a digital background calibration technique that uses a split-least-significant-bit (Split-LSB) weight to simultaneously address both capacitor mismatch and gain nonlinearity in pipelined successive approximation register analog-to-digital converters (SAR ADCs). The key innovation of this approach lies in the use of sub-LSB weights, derived from splitting the LSB capacitor, to detect and correct nonlinearity. By integrating 1-bit dynamic element matching (DEM) with a separate-averaging algorithm, this technique achieves the first offset-immune background calibration capable of calibrating both error sources simultaneously. Behavioral simulations of a 14-bit pipelined SAR ADC show significant performance improvements: the signal-to-noise-and-distortion ratio (SNDR) increases from 52.4 dB to 84.2 dB, and the spurious-free dynamic range (SFDR) rises from 56.3 dB to 104.5 dB. These results validate the effectiveness of the proposed technique.
- 5 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (5) , 2059-2072
A 0.0006-mm 2 , 0.13-pJ/bit, 9–21-Gb/s Sub-Sampling CDR With Inverter-Based Frequency Multiplier and Embedded 1:3 DEMUX in 65-nm CMOS
This article presents a 9–21-Gb/s inductor-less frequency-multiplying sub-sampling (FXSS) clock and data recovery (CDR) circuit with an embedded 1:3 demultiplexer (DEMUX) for multi-lane serial interfaces. It features a compact design with linear modeling and theoretical analysis of the FXSS architecture. An inverter-based frequency multiplier (FX) in the clock feedback path enables the ring voltage-controlled oscillator (RVCO) and transmission-gated retimers to operate at one-third rates. The primary–secondary sub-sampling phase detector (SSPD) supports full-rate triple-frequency clocks. The FX can suppress in-band noises, while a ~200-MHz loop bandwidth (BW) mitigates out-of-band RVCO noise. A duty cycle corrector (DCC) ensures fine retiming deskew. Fabricated in 65-nm CMOS technology, the proposed CDR occupies 0.0006 mm2 and achieves a best-in-class 348.2-fsrms integrated jitter and 0.13-pJ/bit energy efficiency at 21 Gb/s. It demonstrates a jitter tolerance (JTOL) of 0.44 UIpp with a bit error rate (BER) of less than $10^{-12}$ .
- 5 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (5) , 2059-2072
A 0.0006-mm 2 , 0.13-pJ/bit, 9–21-Gb/s Sub-Sampling CDR With Inverter-Based Frequency Multiplier and Embedded 1:3 DEMUX in 65-nm CMOS
This article presents a 9–21-Gb/s inductor-less frequency-multiplying sub-sampling (FXSS) clock and data recovery (CDR) circuit with an embedded 1:3 demultiplexer (DEMUX) for multi-lane serial interfaces. It features a compact design with linear modeling and theoretical analysis of the FXSS architecture. An inverter-based frequency multiplier (FX) in the clock feedback path enables the ring voltage-controlled oscillator (RVCO) and transmission-gated retimers to operate at one-third rates. The primary–secondary sub-sampling phase detector (SSPD) supports full-rate triple-frequency clocks. The FX can suppress in-band noises, while a ~200-MHz loop bandwidth (BW) mitigates out-of-band RVCO noise. A duty cycle corrector (DCC) ensures fine retiming deskew. Fabricated in 65-nm CMOS technology, the proposed CDR occupies 0.0006 mm2 and achieves a best-in-class 348.2-fsrms integrated jitter and 0.13-pJ/bit energy efficiency at 21 Gb/s. It demonstrates a jitter tolerance (JTOL) of 0.44 UIpp with a bit error rate (BER) of less than $10^{-12}$ .
- 22 July 2025
- Published by Elsevier in Microelectronics Journal
- Vol. 164
A linearized PVT-robust FVF input buffer with triode transconductance feedback achieving SFDR > 90 dB at 500-MHz input
- 22 July 2025
- Published by Elsevier in Microelectronics Journal
- Vol. 164
A linearized PVT-robust FVF input buffer with triode transconductance feedback achieving SFDR > 90 dB at 500-MHz input
- 17 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 33 (6) , 1794-1798
Metastable-Dither-Based Digital Background Calibration of Interstage Gain Nonlinearity in Pipelined SAR ADC
A digital background calibration technique is proposed in this brief, utilizing comparator metastability to correct conversion errors from interstage gain errors and higher order nonlinearities for the first time. The method calibrates nonlinear conversion errors by injecting multilevel dithers and observing amplifier gain variations. It offers advantages, such as simple design, high accuracy, fast convergence, and low power consumption. Simulation results demonstrate the effectiveness of the technique, with the signal to noise and distortion ratio (SNDR) and spurious free dynamic range (SFDR) performances of a 14-bit two-stage pipelined successive approximation register analog-to-digital converter (SAR ADC) improving from 60.4 and 73.6 to 84.5 and 110.0 dB, respectively. The convergence speed of the calibration algorithm is 0.8 million samples.
- 17 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 33 (6) , 1794-1798
Metastable-Dither-Based Digital Background Calibration of Interstage Gain Nonlinearity in Pipelined SAR ADC
A digital background calibration technique is proposed in this brief, utilizing comparator metastability to correct conversion errors from interstage gain errors and higher order nonlinearities for the first time. The method calibrates nonlinear conversion errors by injecting multilevel dithers and observing amplifier gain variations. It offers advantages, such as simple design, high accuracy, fast convergence, and low power consumption. Simulation results demonstrate the effectiveness of the technique, with the signal to noise and distortion ratio (SNDR) and spurious free dynamic range (SFDR) performances of a 14-bit two-stage pipelined successive approximation register analog-to-digital converter (SAR ADC) improving from 60.4 and 73.6 to 84.5 and 110.0 dB, respectively. The convergence speed of the calibration algorithm is 0.8 million samples.
- 26 November 2024
- Published by Elsevier in Microelectronics Journal
- Vol. 155
Rapid digital background calibration of bit weights in pipelined SAR ADC based on multi-PN injection
- 26 November 2024
- Published by Elsevier in Microelectronics Journal
- Vol. 155
Rapid digital background calibration of bit weights in pipelined SAR ADC based on multi-PN injection
- 8 October 2024
- Published by Elsevier in Microelectronics Journal
- Vol. 153
A 68.5 dB-SNDR, 12.4-fJ/conv.-step, 100-MS/s pipelined-SAR ADC with PVT-enhanced circuitry
- 8 October 2024
- Published by Elsevier in Microelectronics Journal
- Vol. 153
A 68.5 dB-SNDR, 12.4-fJ/conv.-step, 100-MS/s pipelined-SAR ADC with PVT-enhanced circuitry
- 6 August 2024
- Published by Elsevier in Microelectronics Journal
- Vol. 151
A PVT-robust Gm-R-based residue amplifier with folded positive feedback technique
- 6 August 2024
- Published by Elsevier in Microelectronics Journal
- Vol. 151
A PVT-robust Gm-R-based residue amplifier with folded positive feedback technique