Thomas Toulorge
Research Subjects
Thomas Toulorge has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Michel Rasquin
CENAERO
3 shared publications - Grégoire Winckelmans
Institute of Mechanics, Materials and Civil Engineering (iMMC), Université catholique de Louvain (UCLouvain), 1348 Louvain-la-Neuve, Belgium
2 shared publications - Romain Debroeyer
Institute of Mechanics, Materials, and Civil Engineering (iMMC), Université catholique de Louvain (UCLouvain), 1348 Louvain-la-Neuve, Belgium
2 shared publications - Yann Bartosiewicz
Institute of Mechanics, Materials, and Civil Engineering (iMMC), Université catholique de Louvain (UCLouvain), 1348 Louvain-la-Neuve, Belgium
2 shared publications - Caroline Sainvitu
CENAERO
1 shared publication - Gilles Louppe
University of Liège
1 shared publication
Latest Publications
- 1 August 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (8)
Turbulent injection assisted by diffusion models for scale-resolving simulations
The present research proposes a new memory-efficient method using diffusion models to inject turbulent inflow conditions into large eddy simulation and direct numerical simulation for various flow problems. A guided diffusion model was trained on decaying homogeneous isotropic turbulence samples, characterized by different turbulent kinetic energy levels and integral length scales. Samples generated by the diffusion model accurately reproduce turbulence statistics, such as the energy spectrum and the two-point autocorrelation functions, while preserving the ability to generate instantaneous three-dimensional velocity fields with detailed fluctuations. Physical representativeness is also evaluated by injecting the synthetic samples into a free domain (i.e., without any wall boundary) through an inlet boundary condition. The method demonstrates promising results regarding energy spectrum, spatial correlation, turbulent kinetic energy level, and integral length scales without increasing the development distance as compared to a library-based method.
- 1 August 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (8)
Turbulent injection assisted by diffusion models for scale-resolving simulations
The present research proposes a new memory-efficient method using diffusion models to inject turbulent inflow conditions into large eddy simulation and direct numerical simulation for various flow problems. A guided diffusion model was trained on decaying homogeneous isotropic turbulence samples, characterized by different turbulent kinetic energy levels and integral length scales. Samples generated by the diffusion model accurately reproduce turbulence statistics, such as the energy spectrum and the two-point autocorrelation functions, while preserving the ability to generate instantaneous three-dimensional velocity fields with detailed fluctuations. Physical representativeness is also evaluated by injecting the synthetic samples into a free domain (i.e., without any wall boundary) through an inlet boundary condition. The method demonstrates promising results regarding energy spectrum, spatial correlation, turbulent kinetic energy level, and integral length scales without increasing the development distance as compared to a library-based method.
- 26 July 2025
- Published by Elsevier in International Journal of Heat and Fluid Flow
- Vol. 116
Analysis of entrainment and mixing in a supersonic air ejector using Large-Eddy Simulation
- 26 July 2025
- Published by Elsevier in International Journal of Heat and Fluid Flow
- Vol. 116
Analysis of entrainment and mixing in a supersonic air ejector using Large-Eddy Simulation
- 29 January 2024
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 980, A9
A wall model for large-eddy simulation of highly compressible flows based on a new scaling of the law of the wall
Wall modelling in large-eddy simulation (LES) is of high importance to allow scale resolving simulations of industrial applications. Numerous models were developed and validated for incompressible flows, including a simple quasi-analytical model based on Reichardt's formula that approximates the law of the wall. In this paper, a scaling is proposed to generalize this wall model to highly compressible flows. First, the results of wall-resolved LES (wrLES) of adiabatic compressible turbulent channel flows at $Re_\tau = 1000$ and at centreline Mach numbers of $M_c= 0.76$ and $1.5$ are presented. Then, three potential scalings of the incompressible wall model are proposed, and their a priori performance is evaluated : (i) the Howarth–Stewartson scaling, (ii) an improved Van Driest scaling and (iii) a new scaling obtained from a blending of those two. The results of wall-modelled LES (wmLES) of compressible channel flows using these three models are compared with the reference wrLES data, showing the superior accuracy of the hybrid scaling. The consistency of the new wall model at low Mach numbers is also verified by comparing the results of a wmLES at $M_c= 0.25$ with those of reference incompressible DNS data at $Re_\tau = 1000$ and $5200$ . Finally, the proposed wall model is also applied to a turbulent channel flow at $M_c=1.5$ and $Re_\tau =5200$ .- 29 January 2024
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 980, A9
A wall model for large-eddy simulation of highly compressible flows based on a new scaling of the law of the wall
Wall modelling in large-eddy simulation (LES) is of high importance to allow scale resolving simulations of industrial applications. Numerous models were developed and validated for incompressible flows, including a simple quasi-analytical model based on Reichardt's formula that approximates the law of the wall. In this paper, a scaling is proposed to generalize this wall model to highly compressible flows. First, the results of wall-resolved LES (wrLES) of adiabatic compressible turbulent channel flows at $Re_\tau = 1000$ and at centreline Mach numbers of $M_c= 0.76$ and $1.5$ are presented. Then, three potential scalings of the incompressible wall model are proposed, and their a priori performance is evaluated : (i) the Howarth–Stewartson scaling, (ii) an improved Van Driest scaling and (iii) a new scaling obtained from a blending of those two. The results of wall-modelled LES (wmLES) of compressible channel flows using these three models are compared with the reference wrLES data, showing the superior accuracy of the hybrid scaling. The consistency of the new wall model at low Mach numbers is also verified by comparing the results of a wmLES at $M_c= 0.25$ with those of reference incompressible DNS data at $Re_\tau = 1000$ and $5200$ . Finally, the proposed wall model is also applied to a turbulent channel flow at $M_c=1.5$ and $Re_\tau =5200$ .- 7 March 2019
- Published by Walter de Gruyter GmbH in International Polymer Processing
- Vol. 34 (1) , 37-46
Simulations of Heat Transfer in Thermoplastic Injection Molds Manufactured by Additive Techniques
The cost and quality of complex thermoplastic parts manufactured by injection are traditionally limited by the design constraints on the mold cooling system. A possible way to overcome this problem is to produce the mold by additive manufacturing, which makes it possible to freely design the shape and position of the cooling channels. Such molds can have hollow spaces in order to reduce the manufacturing time by Selective Laser Melting and the use of costly materials. The complex geometry resulting from optimized cooling channels and hollow regions makes the prediction of the cooling system performance difficult. This work aims to devise a numerical methodology for the simulation of heat transfer phenomena between the polymer, the mold and the cooling channels. An Immersed Volume approach is chosen, where the different parts of the domain (i.e. the polymer, the cooling channels, the hollow regions and the mold) are represented implicitly and the thermo-mechanical properties of the materials vary smoothly at the interface between the parts. The energy and momentum equations are solved by a stabilized Finite Element method. In order to accurately resolve the large variations of material properties and the steep temperature gradients at interfaces, state-of-the art anisotropic mesh refinement techniques are employed. In a first step, we perform thermal calculations only. We then consider the proper thermo-mechanical coupling in the packing stage, as well as the ejection stage and the thermal contact resistance between the polymer part and the mold, in order to weight their influence on the part and the mold temperatures. The modeling strategy is first validated on a simple geometry of a center-gated disk and compared with experimental measurements. The agreement between the experimental results and the simulation is good. Simulations are then performed on an industrial case which illustrates the ability of the method to deal with complex geometries.
- 7 March 2019
- Published by Walter de Gruyter GmbH in International Polymer Processing
- Vol. 34 (1) , 37-46
Simulations of Heat Transfer in Thermoplastic Injection Molds Manufactured by Additive Techniques
The cost and quality of complex thermoplastic parts manufactured by injection are traditionally limited by the design constraints on the mold cooling system. A possible way to overcome this problem is to produce the mold by additive manufacturing, which makes it possible to freely design the shape and position of the cooling channels. Such molds can have hollow spaces in order to reduce the manufacturing time by Selective Laser Melting and the use of costly materials. The complex geometry resulting from optimized cooling channels and hollow regions makes the prediction of the cooling system performance difficult. This work aims to devise a numerical methodology for the simulation of heat transfer phenomena between the polymer, the mold and the cooling channels. An Immersed Volume approach is chosen, where the different parts of the domain (i.e. the polymer, the cooling channels, the hollow regions and the mold) are represented implicitly and the thermo-mechanical properties of the materials vary smoothly at the interface between the parts. The energy and momentum equations are solved by a stabilized Finite Element method. In order to accurately resolve the large variations of material properties and the steep temperature gradients at interfaces, state-of-the art anisotropic mesh refinement techniques are employed. In a first step, we perform thermal calculations only. We then consider the proper thermo-mechanical coupling in the packing stage, as well as the ejection stage and the thermal contact resistance between the polymer part and the mold, in order to weight their influence on the part and the mold temperatures. The modeling strategy is first validated on a simple geometry of a center-gated disk and compared with experimental measurements. The agreement between the experimental results and the simulation is good. Simulations are then performed on an industrial case which illustrates the ability of the method to deal with complex geometries.