LELutuf Ertürk

Lutuf Ertürk

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Lutuf Ertürk has a total of 5 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Investigation of Mechanical Properties of Polymer Matrix Composites Reinforced with Waste Iron Powder

    by Mehmet Bulut, Lutuf Ertürk

    Recycling industrial waste plays a crucial role in sustainable environmental balance. Therefore, it is essential to effectively coordinate recycling and waste management, recovering materials like paper, plastic, and metal that are unsuitable for disposal. The investigation of mechanical properties of polymer matrix composites reinforced with waste iron powder can reveal significant enhancements in mechanical properties. Therefore, this study experimentally examines the tensile and flexural mechanical properties of polymer matrix composites reinforced with waste iron metal powder. Morphology investigations were carried out on the fractured tensile and flexural test specimens and comments were made on the results. For this purpose, the effect of reusability of iron powder additive as filler material on mechanical properties at four different iron powder/epoxy weight ratios (0, 2%, 4%, and 8%) was investigated. Subsequently, epoxy/iron powder homogeneous polymer matrix composite blends were cast into metal molds and test specimens were obtained. The results showed that the addition of 4 wt. % iron powder increased the tensile strength by 28%; however, it was concluded that the addition of iron powder negatively affected the flexural strength and modulus with concluding that this decrease in flexural test results was the result of the decrease in the interfacial adhesion strength between iron powder/epoxy.


  • Open Access

    The effect of the borosintering process in iron-based materials on abrasive and sliding wear

    by Lutuf Ertürk, Burhan Selçuk

    Boriding is usually performed separately after sintering in powder metallurgy methods. In the borosintering process, sintering and boriding processes are carried out simultaneously. This saves energy as it shortens the heat treatment time. Additionally, since the heat treatment are shorter in time, it prevents problems that may occur in the materials subjected to this heat treatment. Thanks to the borosintering, boriding is also done on parts produced with powder metallurgy without the need for any extra processing. In this work, iron-based samples were made using powder metallurgy routes. And then, sintering and boronizing processes were applied individually to some samples and simultaneously to others (borosintering). Boriding processes were conducted in solid media (20% B4C, 5% NaF, 75% SiC). Boriding, sintering and borosintering processes were conducted at 950, 1000, and 1050 °C for four hours. SEM was used to investigate the morphology of the produced boride layers, EDX was used to examine the elemental composition, and XRD was used to examine the phases. It is observed that when the temperature rises, the layer thickness increases. It was discovered that the sintered samples were mostly Fe, while the boronized samples were predominantly Fe2B. The microhardness of the boride layers was measured. Additionally, the samples were then subjected to sliding and abrasive wear tests. The hardness values of the boride layer made at 1000 °C and 1050 °C were higher than those at 950 °C. Borosintered samples have been found to be resistant to both sliding and abrasive wear. Borosintered samples, as well as sintered and borided samples, demonstrated similar characteristics. Regarding the process steps and costs, it was determined that the borosintering technique would provide an enormous benefit.


  • Open Access

    Estimation of wind power potential in sivas cumhuriyet university campus using various probability density functions

    by Netice Duman, Halil İbRahim Acar, Lutuf Ertürk

    With the increase in energy consumption, resources are decreasing while costs are rising. The Covid-19 pandemic and wars in some countries have also led to increased costs. Considering the environmental damage, the search for new energy sources and the demand for existing renewable energy sources have increased. Among renewable energy sources, wind energy is one of the most prominent energy sources due to its environmental friendliness. In recent years, studies on wind characteristics and wind energy distribution have been conducted in many parts of the world. But, it has not been conducted that a detailed study using different probability density functions specifically for Sivas province in Türkiye. This study investigated the wind energy potential for Sivas province using various probability density functions. Data from two nearby stations were used in the calculations. Despite the proximity of the stations, it was determined that the emerging wind trends showed some differences. For Station A, it is observed that probability density functions other than Rayleigh provide a better fit, especially at low wind speeds. However, deviations from actual values are observed at certain wind speeds. For Station B, functions other than Weibull show a better fit, although it can be said that the wind characteristics are more irregular in the winter season, and the predicted functions do not provide a better fit. Stations A and B exhibited different wind characteristics, except for the autumn season. It was observed that collecting data and analyzing wind power at the site where a wind farm will be established is quite important. As a result of the study, it was concluded that the potential wind powers at both stations were quite low and not very suitable for wind farm installation.


  • Open Access

    Design and simulation of a standing wave thermoacoustic refrigerator using air as the working fluid

    by Netice Duman, Halil İbRahim Acar, Lutuf Ertürk

    Thermoacoustic refrigerator (TAR) is one of the best technologies accepted as an alternative to traditional cooling systems. Factors such as the fact that TAR systems have minimum environmental and human health problems such as global warming and ozone layer depletion, being lightweight and having no moving parts make these systems seen as promising clean technologies in the future. TAR creates a cooling effect by converting acoustic energy into thermal energy. In this research, a quarter wave standing wave thermoacoustic refrigerator using air as the working fluid and a speaker as an acoustic power source was designed and simulated. An algorithm suitable for the literature on thermoacoustics was used in the design. Simplified linear theory was used in this algorithm and the designed standing wave TAR model was simulated with the Design Environment for Low Amplitude Thermo Acoustic Energy Conversion (DeltaEC) program. In the study, the changes of various parameters along the resonator length were examined and the results were given graphically. Design and simulation cooling coefficient of performance (COP) results were 2.236 and 1.036 respectively.


  • Open Access

    Investigation of The Effect of Borosintering Process on Various Properties of Iron-Based Materials

    by Lutuf Ertürk, Burhan Selçuk

    In this study, samples prepared by pressing iron-based powder mixtures were divided into two different groups; sintering and boriding processes were applied in two steps in some of the samples, and in a single step in some of them. Sintering and boriding processes were applied at 950, 1000 and 1050°C for 2 hours. Various properties of borided and unborided samples in the first group and borosintered samples in the second group were compared. The microstructure in the samples was examined by optical microscope and SEM. Elemental analysis was performed by EDX. Phases formed as a result of boriding were detected by XRD. Surface roughness, microhardness measurements and wear tests were conducted on the samples. In the samples produced by powder metallurgy, the specifications of the structures formed as a result of first sintering and then boronizing process were similar. In both cases, the microhardness values of the material increased and wear-resistant structures were formed. It has been observed that the properties of the resulting structures show some changes depending on the temperature.

  • Atık Malzemelerin Epoksi Matrisli Kompozitlerde Katkı Olarak Kullanımına Yönelik Bir İnceleme

    by Lutuf Ertürk, Sakine Kıratlı

    Dünya nüfusunun sürekli artması, doğal kaynakların tükenmesine hatta zamanla yok olmasına, atık malzemelerin ise artmasına neden olmaktadır. Atık malzemelerin değerlendirilmesi, hem doğada sınırlı miktarda bulunan kaynakların tüketimini azaltmakta hem de atık malzemelerin çevrede oluşturduğu problemleri en aza indirmektedir. Literatürde, kompozit malzemelerde katkı olarak atık malzemelerin kullanımına yönelik birçok çalışma bildirilmiştir. Tarımsal atıklar, hayvansal atıklar ve tekstil atıkları gibi birçok atık malzemenin kompozit malzemelerde kullanıldığı görülmüştür. Yapılan çalışmalarda atık malzemelerin kompozit malzemelerde kullanılmasının çekme, eğilme, kırılma mukavemeti gibi mekanik özellikler açısından birçok avantaj sağladığı sonucuna varılmıştır.


  • Open Access

    Investigation of The Effect of Different Activators on Borosintering Process

    by Lutuf Ertürk, Burhan Selçuk

    In parts produced by the P/M method, boriding is generally applied as a separate process after sintering. If the package boriding process is carried out during the sintering of the powder compact, sintering and boriding can be integrated; This not only prevents parts from deforming due to secondary heating, but can also reduce energy consumption. Carrying out sintering and boriding processes simultaneously is called Borosintering (B/S). Studies in the literature have stated that various material properties are improved thanks to the boride layers formed as a result of the borosintering process. It has been observed that the effect of different boronizing environments on the borosintering process has not been examined in any of the studies. In this study, media containing different weight ratios of silicon carbide (75%, 85%, 90%), boron carbide (5%, 10%, 20%) and the remainder one of various activators (Na2CO3, NaCl, Na2B4O7 (anhydrous borax) and NaF) in the boronizing medium were tested. Wear test (0.6 m/s sliding speed, 52 N load, 500 m distance, counter: 16MnCr5) was applied to some selected samples, the boride layer was examined by SEM, and elemental analysis was performed by EDX. Phases in the boride layer were detected by XRD. The hardness of the layer was measured with a microvickers test machine. The study showed that many different activators can be used in the borosintering process and that activators have a significant effect on the specifications of the boride layer. It was concluded that the NaF activator accelerates the formation of the boride layer more than other activators and creates a boride layer with better properties.

  • Open Access

    Aşınma Test Cihazından Alınan Veriyi İşleyen Bir Program Geliştirilmesi

    by Lutuf Ertürk, Burhan Selçuk

    Bir cihazdan verilerin alınıp işlenmesi için mikrodenetleyicilere ihtiyaç duyulur. Mikrodenetleyiciler evlerde, ofislerde ve araştırma ortamlarında yaygın kullanım alanı bulmuştur. Mikrodenetleyicileri programlamak için birçok sistem mevcut olsa da, Arduino'nun bu konuda daha yaygın olduğu söylenebilir. Açık kaynaklı bir donanım ve yazılıma sahip olması ve kullanıcı etkileşimli topluluğu olan Arduino, 2005 yılından bu yana mikro denetleyici tabanlı Arduino kartları üretmektedir. Literatürde Arduino ile tasarlanan birçok sistem vardır. Bu çalışmada ise Arduino (Nano) geliştirme kartı kullanılarak, Sürtünme ve Aşınma Test Cihazı’nın analog sinyal çıkışlarından verilerin alınıp işlenilmesi amaçlanmıştır. Arduino ile bilgisayar arasında verilerin aktarımı ve işlenmesi için Object Pascal dilinde derleyicinin entegre olduğu, açık kaynak kodlu Lazarus uygulaması kullanılmıştır. Aşınma sonucu makine parçalarında yalnızca kütle kaybı değil, boyutsal değişimler ve yüzey hasarları da oluşabilir. Bu nedenle aşınma, üretimin sürekliliği ve kalitesi bakımından oldukça önem arz etmektedir. Aşınma miktarını en aza indirmek için, aşınmaya neden olan parametrelerin incelenmesi gerekmektedir. Bu nedenle, geliştirilen program aşınma parametrelerinin incelenmesi açısından oldukça önemlidir.