APAleksandra Patarić

Aleksandra Patarić

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Aleksandra Patarić has a total of 20 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Composition Driven Redistribution of Feeding Mechanisms in Hypoeutectic Al–Si–Mg Alloys

    by Aleksandra Patarić, Mile Djurdjevic, Srecko Manasijevic, Srecko Stopic, Marija Mihailović

    This study provides a systematic quantitative assessment of the influence of silicon (5–9 wt.%) and magnesium (0–0.6 wt.%) on the solidification behavior and feeding mechanisms of hypoeutectic Al–Si–Mg casting alloys. Cooling curve analysis combined with first-derivative and ΔT (Tw − Tc) evaluation was used to determine characteristic solidification temperatures, including the liquidus, dendrite coherency, rigidity, and solidus temperatures, enabling the precise delineation of feeding regions. Increasing silicon content reduced all characteristic temperatures, while magnesium addition exerted a more pronounced effect on rigidity and solidus temperatures, significantly redistributing the relative contributions of mass, interdendritic, and burst feeding. In particular, magnesium addition systematically expanded the interdendritic feeding interval and reduced the burst-feeding range, promoting earlier dendrite interlocking and restricting melt flow during late-stage solidification. Quantitative temperature ratio analysis revealed that magnesium plays a dominant role in shifting feeding toward interdendritic-controlled flow, especially in low-Si alloys. Sand Hourglass testing confirmed that this redistribution directly correlated with increased shrinkage porosity, with the highest porosity observed in the AlSi9Mg0.6 alloy. The results establish a quantitative link between alloy composition, feeding redistribution, and porosity susceptibility, providing a practical framework for optimizing the design and casting performance of Al–Si–Mg alloys.

  • Open Access

    The Role of Silicon During Solidification Process of Cast Al-Si-Mg Alloys

    by Aleksandra Patarić, Mile Djurdjevic, Srecko Manasijevic, Srecko Stopic, Marija Mihailović

    Hypoeutectic Al-Si-Mg alloys are among the most widely used casting materials in the automotive and aerospace industries due to their low density, high strength-to-weight ratio, corrosion resistance, and good castability. A critical challenge during solidification is shrinkage porosity, which arises from insufficient feeding and significantly reduces casting reliability. While the role of silicon in altering the phase diagram of Al-Si-Mg alloys is well-understood, its direct impact on feeding behavior has not been previously quantified in detail. In this study, the influence of silicon content (5–9 wt.%) on feeding ability was systematically investigated using thermal analysis (TA). By analyzing cooling curves, first derivatives, and ΔT curves, key solidification temperatures, including the liquidus, dendrite coherency, rigidity, and solidus, were precisely identified. For the first time, these data were used to quantitatively define all five feeding regions (liquid, mass, interdendritic, burst, and solid feeding) as a function of silicon content. The results demonstrate that increasing the Si content decreases the liquidus and dendrite coherency temperatures, raises the rigidity and solidus temperatures, and shortens the overall feeding ranges, particularly the interdendritic region (~32 °C reduction). This novel TA-based quantification of feeding regions provides insights that extend beyond classical phase diagram interpretation. The findings confirm that higher Si contents improve feeding ability by narrowing the freezing range and reducing the risk of porosity, while also providing a unique dataset for validating casting simulation software. The results also confirm that increasing the silicon content enhances feeding ability and improves castability by narrowing the freezing range and promoting more uniform solidification in Al-Si-Mg alloys. The study therefore bridges fundamental solidification science with industrial practice, supporting improved alloy design and defect control in Al-Si-Mg castings.


  • FACTORS INFLUENCING THE MECHANICAL PROPERTIES OF HIGH CHROMIUM WHITE CAST IRON

    by Aleksandra Patarić, Marija Mihailović, Branka Jordović

    The high chromium white cast iron (HCWCI) has been in use for decades and is expected to remain popular due to its superb wear resistance. This wear resistant material is recognized for its superior hardness, toughness, and corrosion resistance. It is widely used in industries such as mining, cement, and power generation, where high abrasion and impact resistance are essential. The studies in this paper were conducted on an alloy containing 24.48% chromium, 2.66% carbon 1.32% molybdenum, 1.6% nickel, 0.99% silicon and 0.96% manganese. Mechanical and microstructural characterization was carried out on both as-cast samples and samples subjected to appropriate heat treatment (quenching 1000 oC/2h air cooling, quenching followed by tempering at 250oC/3h and quenching to -196oC in liquid nitrogen). Mechanical characterization involved measuring Vickers hardness and assessing toughness using Sarpi's pendulum. Hardness and toughness results of samples are correlated with the obtained microstructure. The applied heat treatment led to an increase in the hardness values, while toughness values remained largely unchanged, which is a consequence of the unmodified forms of the existing carbides. Various types of carbides (M3C and M7C3 type, but also for this alloy typical Mo2C carbide) can be observed through etching with Murakam's reagent.

  • DETERMINATION OF LATENT HEAT FOR ALSI7CU1 ALLOY APPLYING DSC, TA, AND COMMERCIAL SOFTWARE PACKAGES

    by Mile Djurdjevic, Srećko Manasijević, Aleksandra Patarić, Marija Mihailović, Radomir Radisa

    Latent heat of cast hypoeutectic aluminum alloys is commonly measured using Differential Scanning Calorimetry (DSC) or calculated using software packages (Thermo-Calc, JMatPro, FactSage) as well as applying cooling curve analysis (Thermal analysis technique). This study used the DSC method to comprehensively evaluate the accuracy of calculated latent heat for a specific AlSi7Cu1 alloy, considering its solidification under different cooling conditions. The alloy was analyzed under three distinct cooling/heating rates: 6, 10, and 50 °C/min. The commercial software packages (Thermo-Calc, JMatPro, and Fact Sage) and thermal analysis techniques (Newtonian, Fourier, and Energy balance methods) were used to calculate the investigated alloys' latent heat. The results obtained show good agreement between the measured and calculated values. Higher cooling rates, such as 50 °C/min, resulted in a reduced latent heat release compared to slower rates, such as 10 °C/min and 6 °C/min.

  • ALUMINUM'S JOURNEY: CELEBRATING TWO CENTURIES OF METALLURGICAL INNOVATION AND INDUSTRIAL GROWTH

    by Mile Djurdjevic, Marija Mihailović, Aleksandra Patarić, Srećko Manasijević

    This paper observes the 200-year journey of aluminum from its discovery to becoming one of the world's most essential industrial materials. It traces aluminum's evolution from its early identification in the 18th century through key technological milestones that transformed it from a precious metal to industrial goods. The important innovations including Oersted's first aluminum production in 1825, the Hall-Héroult electrolytic process of 1886, and Bayer's method for extracting alumina from bauxite in 1888 are reviewed in this paper. Additionally, it highlights significant metallurgical developments by A. Wilm and A. Pacz that enhanced aluminum's mechanical properties through alloying, modifying and grain refining. The work explores aluminum's unique combination of properties such as lightweight strength, corrosion resistance, electrical conductivity, and recyclability that have established it as a fundamental material across diverse industries from aerospace to construction, automotive, chemical, agriculture, medical and electronics. Finally, it analyzes production trends from 1900 to present day, documenting growth from less than 1 million tons annually to 70 million tons in 2024, while examining the socioeconomic factors and technological advancements that have shaped aluminum's remarkable industrial trajectory.

  • Open Access

    Statistical evolution of non-metallic inclusions in continuous cast Al-killed steel

    by Karlo Raić, Mile Đurđević, Srećko Manasijević, Aleksandra Patarić, Marija Mihailović

    The objective of this study is to develop statistical relationships that will enable the quantification of non-metallic inclusion content in continuously cast low-carbon, aluminum-killed deep-drawing steel in situations where standard techniques make metallographic control challenging or impossible. Further considerations can be focused on predicting the model of the size distribution curve after the quantitative characterization of non-metallic inclusions in steel is completed. So, the potential of reconstructing the entire content of non-metallic inclusions in steel will be estimated, and the influence of limiting factors can be assessed.

  • Open Access

    Role of magnesium in solidification feeding of hypoeutectic Al-Si5-Mg alloys

    by Mile B. Đurđević, Srećko Manasijević, Aleksandra Patarić, Marija Mihailović, Karlo Raić

    The growing demand for high-performance Al-Si casting alloys stems from their excellent mechanical properties in engineering applications. Hypoeutectic Al-Si-Mg alloys offer superior fluidity, low thermal expansion, and corrosion resistance; however, they face solidification challenges such as shrinkage porosity. This study investigates magnesium's influence on feeding regions in AlSi5Mg alloys. Results show that increasing magnesium content from 0% to 0.6% significantly affects interdendritic and burst feeding regions, potentially impacting shrinkage porosity formation.

  • Open Access

    Impact of Mg on the Feeding Ability of Cast Al–Si7–Mg(0_0.2_0.4_0.6) Alloys

    by Mile Djurdjevic, Srecko Manasijevic, Aleksandra Patarić, Srecko Stopic, Marija Mihailović

    The demand for high-performance Al–Si casting alloys is driven by their mechanical properties, making them popular in automotive, aerospace, and engineering industries. These alloys, especially hypoeutectic Al–Si–Mg, offer benefits like high fluidity, low thermal expansion, and good corrosion resistance. Silicon and magnesium primarily define their microstructure and mechanical properties. Silicon enhances fluidity, while magnesium improves strength and fatigue resistance. However, challenges like shrinkage porosity persist during solidification. Understanding solidification feeding regions is crucial, influenced by factors such as chemical composition, solidification characteristics, and casting design. This study investigates magnesium’s influence on feeding ability in hypoeutectic Al–Si7–Mg alloys through experimental tests. Increasing magnesium content from 0% to 0.6% affects the interdendritic and burst feeding regions. This could impact shrinkage porosity formation. The “Sand Hourglass” test results indicate a rise in porosity levels with higher magnesium content, which is linked to the narrowing of interdendritic channels and the formation of magnesium-rich intermetallic compounds. These changes hinder the liquid metal flow, worsening shrinkage porosity. Therefore, magnesium’s role in expanding the interdendritic region is a key factor in developing porosity in cast hypoeutectic Al–Si7–Mg alloys. This study highlights that porosity levels increase from 0% in magnesium-free Al–Si7 to 0.84% in Al–Si7–Mg0.6, underscoring magnesium’s significant impact on the occurrence of porosity in these alloys.


  • Open Access

    Prediction of thermal and mechanical properties of acrylate-based composites using artificial neural network modeling

    by Vanja Z. Mališić, Milada L. Pezo, Aleksandra N. Jelić, Aleksandra S. Patarić, Slaviša S. Putić

    Poly(methyl methacrylate) (PMMA) has a broad spectrum of uses, especially in medical applications. The role of fine-grained alumina particles of PMMA composites was investigated in this study. The composites were based on PMMA modified with dimethyl itaconate (DMI) as a matrix and alumina particles (Al2O3) and alumina doped with iron (Al2O3-Fe) modified with 3-aminopropyl-trimethoxysilane (AM) and flax oil fatty acid methyl esters (biodiesel) as reinforcements. Three particle sizes were measured (~0.4, ~0.6 and ~1.2 ?m). The highest thermal conductivity values were measured for the composite 5 wt.% Al2O3-Fe-AM. With the addition of 3 wt.% Al2O3-AM to the PMMA/DMI matrix, mechanical properties were improved (tensile strength, strain, and modulus of elasticity). An artificial neural network model based on the Broyden-Fletcher-Goldfarb-Shanno iterative algorithm was investigated for prediction of thermal conductivity and mechanical properties of the composites showing satisfactory results. This is relevant for applications for optimization of dental materials to produce dentures, which were exposed to variations in temperature during the application.