Karol Dąbrowski
Karol Dąbrowski has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Piotr Martyniuk
Institute of Applied Physics, Military University of Technology, 2 Kaliskiego St., 00-908 Warsaw, Poland
8 shared publications - Waldemar Gawron
Institute of Applied Physics, Military University of Technology, 2 Kaliskiego St., 00-908 Warsaw, Poland
7 shared publications - Bartłomiej Seredyński
Institute of Applied Physics, Military University of Technology, 2. Kaliskiego St., 00-908 Warsaw, Poland
5 shared publications - Łukasz Kubiszyn
VIGO Photonics S.A.
4 shared publications Łukasz Kubiszyn
VIGO Photonics S.A.
3 shared publicationsBartłomiej Seredyński
VIGO Photonics S.A., Oarw Mazowiecki, Poland
2 shared publications
Latest Publications
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (9) , 5659-5664
Electric Gain Effect in LWIR ICIPs Under Thermoelectric Cooling (200/230 K)
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (9) , 5659-5664
Electric Gain Effect in LWIR ICIPs Under Thermoelectric Cooling (200/230 K)
- Open Access
- 14 December 2025
- Published by Centrum Rzeczoznawstwa Budowlanego Sp z. o.o. in Inżynieria Bezpieczeństwa Obiektów Antropogenicznych
- No. 4,p. 71-81
Autonomous private networks (SNPN) for crisis management: ensuring communication continuity in case of public infrastructure failure
Modern crisis management requires resilient communication systems capable of operating independently from public telecommunication infrastructure during emergencies. This paper analyzes Standalone Non-Public Networks (SNPN) based on 5G New Radio technology as an autonomous solution for crisis communication. The research determines optimal SNPN configurations ensuring communication continuity in disaster scenarios while maintaining operational and budget constraints. The methodology employs advanced ray-tracing propagation models and three-dimensional environmental analysis in the 4 GHz band, incorporating adaptive beamforming and satellite backhaul integration. Results demonstrate that localized SNPN deployments provide superior interference management and critical redundancy compared to public networks. Implementation of Ultra-Reliable Low-Latency Communications (URLLC) and network slicing enables effective prioritization of rescue traffic. Strategic base station positioning achieves optimal balance between coverage, performance, and cost efficiency. The study confirms that software-defined SNPN architectures significantly enhance communication resilience against external failures, ensuring operational continuity when terrestrial infrastructure is compromised.
- 14 December 2025
- Published by Centrum Rzeczoznawstwa Budowlanego Sp z. o.o. in Inżynieria Bezpieczeństwa Obiektów Antropogenicznych
- No. 4,p. 71-81
Open AccessAutonomous private networks (SNPN) for crisis management: ensuring communication continuity in case of public infrastructure failure
Modern crisis management requires resilient communication systems capable of operating independently from public telecommunication infrastructure during emergencies. This paper analyzes Standalone Non-Public Networks (SNPN) based on 5G New Radio technology as an autonomous solution for crisis communication. The research determines optimal SNPN configurations ensuring communication continuity in disaster scenarios while maintaining operational and budget constraints. The methodology employs advanced ray-tracing propagation models and three-dimensional environmental analysis in the 4 GHz band, incorporating adaptive beamforming and satellite backhaul integration. Results demonstrate that localized SNPN deployments provide superior interference management and critical redundancy compared to public networks. Implementation of Ultra-Reliable Low-Latency Communications (URLLC) and network slicing enables effective prioritization of rescue traffic. Strategic base station positioning achieves optimal balance between coverage, performance, and cost efficiency. The study confirms that software-defined SNPN architectures significantly enhance communication resilience against external failures, ensuring operational continuity when terrestrial infrastructure is compromised.
- Open Access
- 4 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 18 (1) , 1-5
III-V Multistage Detectors as an Alternative to MCT at Room and Thermoelectric Cooling Temperature (200 K)
This paper presents a performance comparison of commonly used mercury cadmium telluride (MCT) detectors and interband cascade infrared photodetectors (ICIPs) based on the InAs/InAsSb type-II superlattice (T2SL – “new wave material”) from mid- to very long-wave infrared (MWIR-LWIR-VLWIR), fabricated at VIGO Photonics S.A. All results show the detectors operating at high temperatures using immersion lens technology. For devices optimized for the MWIR, the detectivity of MCT is still higher than ICIP, especially when cooled, however, in the LWIR and VLWIR, the ICIP often exhibits performance comparable or higher than the MCT at room temperature. Moreover, the paper shows the capability of the cascade design to increase the operating bandwidth in the MWIR-VLWIR and greater possibility of the energy band engineering.
- 4 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 18 (1) , 1-5
Open AccessIII-V Multistage Detectors as an Alternative to MCT at Room and Thermoelectric Cooling Temperature (200 K)
This paper presents a performance comparison of commonly used mercury cadmium telluride (MCT) detectors and interband cascade infrared photodetectors (ICIPs) based on the InAs/InAsSb type-II superlattice (T2SL – “new wave material”) from mid- to very long-wave infrared (MWIR-LWIR-VLWIR), fabricated at VIGO Photonics S.A. All results show the detectors operating at high temperatures using immersion lens technology. For devices optimized for the MWIR, the detectivity of MCT is still higher than ICIP, especially when cooled, however, in the LWIR and VLWIR, the ICIP often exhibits performance comparable or higher than the MCT at room temperature. Moreover, the paper shows the capability of the cascade design to increase the operating bandwidth in the MWIR-VLWIR and greater possibility of the energy band engineering.
- Open Access
- 1 December 2025
- Published by Centrum Rzeczoznawstwa Budowlanego Sp z. o.o. in Inżynieria Bezpieczeństwa Obiektów Antropogenicznych
- No. 4,p. 57-70
Assessment of the impact of radio signal quality on the quality of network services
This study establishes quantitative relationships between physical-layer radio indicators and application-layer service quality in fifth-generation New Radio standalone non-public networks. Complete network infrastructure was deployed to measure Reference Signal Received Power, Reference Signal Received Quality, and Signal-to-Interference-plus-Noise Ratio across locations spanning excellent to poor propagation conditions. Throughput measurements demonstrated that network architecture and transport protocol selection significantly impact achievable data rates, with downlink performance strongly correlated to signal quality gradients. Voice over Internet Protocol assessment revealed distinct performance regimes, with catastrophic degradation occurring below critical radio thresholds. Results confirm that physical-layer measurements reliably predict user-experienced quality and that specific parameter boundaries draw transitions between acceptable and unacceptable service performance. These findings provide benchmarks for coverage planning and performance prediction in private mobile networks where predictable service quality is essential.
- 1 December 2025
- Published by Centrum Rzeczoznawstwa Budowlanego Sp z. o.o. in Inżynieria Bezpieczeństwa Obiektów Antropogenicznych
- No. 4,p. 57-70
Open AccessAssessment of the impact of radio signal quality on the quality of network services
This study establishes quantitative relationships between physical-layer radio indicators and application-layer service quality in fifth-generation New Radio standalone non-public networks. Complete network infrastructure was deployed to measure Reference Signal Received Power, Reference Signal Received Quality, and Signal-to-Interference-plus-Noise Ratio across locations spanning excellent to poor propagation conditions. Throughput measurements demonstrated that network architecture and transport protocol selection significantly impact achievable data rates, with downlink performance strongly correlated to signal quality gradients. Voice over Internet Protocol assessment revealed distinct performance regimes, with catastrophic degradation occurring below critical radio thresholds. Results confirm that physical-layer measurements reliably predict user-experienced quality and that specific parameter boundaries draw transitions between acceptable and unacceptable service performance. These findings provide benchmarks for coverage planning and performance prediction in private mobile networks where predictable service quality is essential.
- 28 October 2025
- Published by Optica Publishing Group in Optics Letters
- Vol. 50 (21) , 6698-6701
MWIR/LWIR/VLWIR ICIPs—the utmost performance at room temperature
This paper presents the highest, to the best of our knowledge, performance reached for interband cascade detectors at VIGO Photonics, versus absorbers’ doping, thicknesses, and number of stages, for the 50% cut-off wavelength ( λ cut-off(50%) , the spectral response drops to 50% of its peak value), ranging from 6.1 to 13.9 µm and operating at room temperature (293 K). All analyzed devices were based on the InAs/InAsSb type-II superlattice (T2SL), where subsequent cells were connected by heavily doped p + /n + tunneling junctions. In the case of detectors optimized for the LWIR/VLWIR ranges, GaAs immersion lens technology was used to maximize performance. The peak detectivity ( D p e a k ∗ ) ranges from 7.46 × 10 7 Jones for the detector with λ cut-off(50%) ~13.9 µm, to 1.2 × 10 9 Jones for λ cut-off(50%) ~10.1 µm.
- 28 October 2025
- Published by Optica Publishing Group in Optics Letters
- Vol. 50 (21) , 6698-6701
MWIR/LWIR/VLWIR ICIPs—the utmost performance at room temperature
This paper presents the highest, to the best of our knowledge, performance reached for interband cascade detectors at VIGO Photonics, versus absorbers’ doping, thicknesses, and number of stages, for the 50% cut-off wavelength ( λ cut-off(50%) , the spectral response drops to 50% of its peak value), ranging from 6.1 to 13.9 µm and operating at room temperature (293 K). All analyzed devices were based on the InAs/InAsSb type-II superlattice (T2SL), where subsequent cells were connected by heavily doped p + /n + tunneling junctions. In the case of detectors optimized for the LWIR/VLWIR ranges, GaAs immersion lens technology was used to maximize performance. The peak detectivity ( D p e a k ∗ ) ranges from 7.46 × 10 7 Jones for the detector with λ cut-off(50%) ~13.9 µm, to 1.2 × 10 9 Jones for λ cut-off(50%) ~10.1 µm.
- 25 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (2) , 155-158
Photocurrent-Induced 1/f Noise in AIIIBV T2SLs Infrared Detectors
This letter focuses on the 1/f noise induced by a photocurrent in infrared (IR) detectors based on the AIIIBV InAs/GaSb, and InAs/InAsSb type-II superlattices (T2SLs) optimized for mid-, or long-wavelength range. The relative photocurrent 1/f noise αph≈3×10-11 and αph≈7×10-11 were found for detectors based on InAs/GaSb and InAs/InAsSb T2SLs, respectively. It was shown that the dark current generates 1/f noise much more efficiently than the photocurrent in all detectors. The lowest relative dark current 1/f noise αd≈4×10-8 was obtained for interband cascade InAs/InAsSb T2SL detectors. The correlation between the photocurrent and the dark current 1/f noises was extracted, suggesting that both components partially origin the same source.
- 25 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (2) , 155-158
Photocurrent-Induced 1/f Noise in AIIIBV T2SLs Infrared Detectors
This letter focuses on the 1/f noise induced by a photocurrent in infrared (IR) detectors based on the AIIIBV InAs/GaSb, and InAs/InAsSb type-II superlattices (T2SLs) optimized for mid-, or long-wavelength range. The relative photocurrent 1/f noise αph≈3×10-11 and αph≈7×10-11 were found for detectors based on InAs/GaSb and InAs/InAsSb T2SLs, respectively. It was shown that the dark current generates 1/f noise much more efficiently than the photocurrent in all detectors. The lowest relative dark current 1/f noise αd≈4×10-8 was obtained for interband cascade InAs/InAsSb T2SL detectors. The correlation between the photocurrent and the dark current 1/f noises was extracted, suggesting that both components partially origin the same source.
- 2 December 2024
- Published by Elsevier in Optics & Laser Technology
- Vol. 182
Response time of the type-II superlattice InAs/InAsSb mid-infrared interband cascade photodetector for HOT conditions
- 2 December 2024
- Published by Elsevier in Optics & Laser Technology
- Vol. 182
Response time of the type-II superlattice InAs/InAsSb mid-infrared interband cascade photodetector for HOT conditions
- 1 November 2024
- Published by SPIE-Intl Soc Optical Eng
- Vol. 13200, 32-239
Latest development on IR detector technology at WAT-VIGO laboratory
The aim of the paper is to review the main achievements in the research of HgCdTe ternary alloy and InAs/InAsSb type-II superlattice material to indicate the Polish contribution to the development of medium and long wavelength infrared photodetectors. Research and development efforts in the WAT-VIGO joint laboratory have focused on the metal-organic chemical vapor deposition (from 2003) and molecular beam epitaxy (from 2015). At present stage of development, the photoconductive and photovoltaic HgCdTe detectors are gradually replaced with novel device designs based on III-V material system. T2SL devices complement the offer of MCT ones in applications where it is necessary to ensure, among others: higher resistance to difficult operating conditions and high uniformity of parameters of multi-element detectors.
- 1 November 2024
- Published by SPIE-Intl Soc Optical Eng
- Vol. 13200, 32-239
Latest development on IR detector technology at WAT-VIGO laboratory
The aim of the paper is to review the main achievements in the research of HgCdTe ternary alloy and InAs/InAsSb type-II superlattice material to indicate the Polish contribution to the development of medium and long wavelength infrared photodetectors. Research and development efforts in the WAT-VIGO joint laboratory have focused on the metal-organic chemical vapor deposition (from 2003) and molecular beam epitaxy (from 2015). At present stage of development, the photoconductive and photovoltaic HgCdTe detectors are gradually replaced with novel device designs based on III-V material system. T2SL devices complement the offer of MCT ones in applications where it is necessary to ensure, among others: higher resistance to difficult operating conditions and high uniformity of parameters of multi-element detectors.
- Open Access
- 26 August 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (17) , 1393
Optical Characterization of the Interband Cascade LWIR Detectors with Type-II InAs/InAsSb Superlattice Absorber
The long-wave infrared (LWIR) interband cascade detector with type-II superlattices (T2SLs) and a gallium-free (“Ga-free”) InAs/InAsSb (x = 0.39) absorber was characterized by photoluminescence (PL) and spectral response (SR) methods. Heterostructures were grown by molecular beam epitaxy (MBE) on a GaAs substrate (001) orientation. The crystallographic quality was confirmed by high-resolution X-Ray diffraction (HRXRD). Two independent methods, combined with theoretical calculations, were able to determine the transitions between the superlattice minibands. Moreover, transitions from the trap states were determined. Studies of the PL intensity as a function of the excitation laser power allowed the identification of optical transitions. The determined effective energy gap (Eg) of the tested absorber layer was 116 meV at 300 K. The transition from the first light hole miniband to the first electron miniband was red-shifted by 76 meV. The detected defects’ energy states were constant versus temperature. Their values were 85 meV and 112 meV, respectively. Moreover, two additional transitions from acceptor levels in cryogenic temperature were determined by being shifted from blue to Eg by 6 meV and 16 meV, respectively.
- 26 August 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (17) , 1393
Open AccessOptical Characterization of the Interband Cascade LWIR Detectors with Type-II InAs/InAsSb Superlattice Absorber
The long-wave infrared (LWIR) interband cascade detector with type-II superlattices (T2SLs) and a gallium-free (“Ga-free”) InAs/InAsSb (x = 0.39) absorber was characterized by photoluminescence (PL) and spectral response (SR) methods. Heterostructures were grown by molecular beam epitaxy (MBE) on a GaAs substrate (001) orientation. The crystallographic quality was confirmed by high-resolution X-Ray diffraction (HRXRD). Two independent methods, combined with theoretical calculations, were able to determine the transitions between the superlattice minibands. Moreover, transitions from the trap states were determined. Studies of the PL intensity as a function of the excitation laser power allowed the identification of optical transitions. The determined effective energy gap (Eg) of the tested absorber layer was 116 meV at 300 K. The transition from the first light hole miniband to the first electron miniband was red-shifted by 76 meV. The detected defects’ energy states were constant versus temperature. Their values were 85 meV and 112 meV, respectively. Moreover, two additional transitions from acceptor levels in cryogenic temperature were determined by being shifted from blue to Eg by 6 meV and 16 meV, respectively.
- Open Access
Response Time of III-V Multistage Detectors Based on the “Ga-Free” InAs/InAsSb Type-II Superlattice
This paper presents a response time/time constant of III-V material-based interband long wavelength multistage infrared detector optimized for a wavelength of 10.6 µm at 200 K. The device is based on the InAs/InAsSb type-II superlattice with highly doped p+/n+ tunneling junctions among the stages. The detector exhibits a response time of 9.87 ns under zero voltage condition, while for 0.15 V reverse bias, that time decreases to approximately 350 ps. The presented device shows a significant increase in response time, especially for low bias, and for a voltage of −0.2 V, the decrease in the detector’s response time by an order of magnitude was estimated. Higher voltage slightly affects the time constant, and between −0.3 V and −1 V, it varies between 300 and 400 ps. The significant change in the detector’s response time between −0.1 V and −0.2 V probably results from electric field drop over entire absorber region. The optimal operating condition can be reached for −0.15 V, where the time constant reaches approximately 350 ns with peak detectivity at a level of ~3 × 109 Jones.
Open AccessResponse Time of III-V Multistage Detectors Based on the “Ga-Free” InAs/InAsSb Type-II Superlattice
This paper presents a response time/time constant of III-V material-based interband long wavelength multistage infrared detector optimized for a wavelength of 10.6 µm at 200 K. The device is based on the InAs/InAsSb type-II superlattice with highly doped p+/n+ tunneling junctions among the stages. The detector exhibits a response time of 9.87 ns under zero voltage condition, while for 0.15 V reverse bias, that time decreases to approximately 350 ps. The presented device shows a significant increase in response time, especially for low bias, and for a voltage of −0.2 V, the decrease in the detector’s response time by an order of magnitude was estimated. Higher voltage slightly affects the time constant, and between −0.3 V and −1 V, it varies between 300 and 400 ps. The significant change in the detector’s response time between −0.1 V and −0.2 V probably results from electric field drop over entire absorber region. The optimal operating condition can be reached for −0.15 V, where the time constant reaches approximately 350 ns with peak detectivity at a level of ~3 × 109 Jones.