Jun Shi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jun Shi has a total of 85 co-authors. Here are the top co-authors by number of shared publications:
- Kun Wu
Guangzhou Institute of Chemistry, Chinese Academy of Sciences
21 shared publications Hangzhou Wang
Guangzhou Institute of Chemistry, Chinese Academy of Sciences
11 shared publicationsChenguang Kong
Guangzhou Institute of Chemistry, Chinese Academy of Sciences, Guangzhou 510650, People's Republic of China
10 shared publicationsXiaobin Li
Guangzhou Institute of Chemistry, Chinese Academy of Sciences, Guangzhou 510650, People’s Republic of China
9 shared publicationsEnding Zhang
Guangzhou Institute of Chemistry, Chinese Academy of Sciences, Guangzhou 510650, People’s Republic of China
8 shared publicationsShumin Jiang
Guangzhou Institute of Chemistry, Chinese Academy of Sciences
8 shared publications
Latest Publications
- 26 October 2026
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 8 (21) , 19534-19546
Functionalized Tetrasiloxane Enables Superhydrophilicity and Water Drainage in Waterborne Acrylic Coatings
Water condensation can reduce optical clarity on transparent surfaces, while causing persistent water retention on heat-transfer surfaces. Although superhydrophilic coatings promote droplet spreading, enhanced hydrophilicity alone does not necessarily ensure efficient water drainage. In this work, a waterborne acrylic coating combining superhydrophilic wetting with gravity-driven water removal was developed using a polyether- and epoxy-functionalized tetrasiloxane (PESiE). PESiE was synthesized by sequential hydrosilylation and incorporated into a glycidyl-functional acrylic latex (PBMG). Meanwhile, γ-aminopropyltriethoxysilane (KH550) was introduced as an amino-functional silane to promote network formation through possible amino–epoxy reactions and silanol condensation. The surface composition and morphology were characterized by XPS depth profiling and SEM, while water-management performance was evaluated through contact angle, droplet-sliding, spray-drainage, and antifogging tests. The results showed that PESiE was preferentially enriched near the coating surface, where the enriched polyether- and siloxane-containing species may increase surface water affinity and facilitate water spreading. At an optimized PESiE content of 7.5 wt %, the water contact angle decreased from 72.5° to 8.1°, while the apparent water-removal efficiency at 300 s increased from 5.0% to 75.0%. The optimized coating also maintained approximately 86–90% visible-light transmittance after vapor exposure and about 88% transmittance over 20 fogging/drying cycles. Taken together, these results show that the coating combines strong water affinity with effective water removal, while maintaining high optical transparency and repeatable antifogging performance. This formulation-based strategy provides a simple route for condensate-management coatings, with potential applications on heat-exchanger fins, antifogging glass, observation windows, and optical protective covers.
- 26 October 2026
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 8 (21) , 19534-19546
Functionalized Tetrasiloxane Enables Superhydrophilicity and Water Drainage in Waterborne Acrylic Coatings
Water condensation can reduce optical clarity on transparent surfaces, while causing persistent water retention on heat-transfer surfaces. Although superhydrophilic coatings promote droplet spreading, enhanced hydrophilicity alone does not necessarily ensure efficient water drainage. In this work, a waterborne acrylic coating combining superhydrophilic wetting with gravity-driven water removal was developed using a polyether- and epoxy-functionalized tetrasiloxane (PESiE). PESiE was synthesized by sequential hydrosilylation and incorporated into a glycidyl-functional acrylic latex (PBMG). Meanwhile, γ-aminopropyltriethoxysilane (KH550) was introduced as an amino-functional silane to promote network formation through possible amino–epoxy reactions and silanol condensation. The surface composition and morphology were characterized by XPS depth profiling and SEM, while water-management performance was evaluated through contact angle, droplet-sliding, spray-drainage, and antifogging tests. The results showed that PESiE was preferentially enriched near the coating surface, where the enriched polyether- and siloxane-containing species may increase surface water affinity and facilitate water spreading. At an optimized PESiE content of 7.5 wt %, the water contact angle decreased from 72.5° to 8.1°, while the apparent water-removal efficiency at 300 s increased from 5.0% to 75.0%. The optimized coating also maintained approximately 86–90% visible-light transmittance after vapor exposure and about 88% transmittance over 20 fogging/drying cycles. Taken together, these results show that the coating combines strong water affinity with effective water removal, while maintaining high optical transparency and repeatable antifogging performance. This formulation-based strategy provides a simple route for condensate-management coatings, with potential applications on heat-exchanger fins, antifogging glass, observation windows, and optical protective covers.
- 11 May 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 14 (24) , 10661-10675
A mechanically robust self-healing polysiloxane via Fe 3+ -dopamine metal coordination for flexible sensors
In recent years, wearable electronic devices based on polydimethylsiloxane (PDMS) have garnered increasing attention. However, the limited mechanical strength of PDMS itself and its poor self-healing properties after prolonged use restrict its application in flexible sensors. Here, we propose a novel approach to successfully prepare a self-healing polydimethylsiloxane material (Si-DOPAx-Fey) with enhanced mechanical properties by introducing a metallic coordination network. The obtained Si-DOPAx-Fey exhibited a maximum tensile strength of 652 kPa and an elongation at break of 133%. When fracture damage occurred, Si-DOPA3-Fe0.6 achieved a self-healing efficiency of 90.3% after 8 hours of repair at room temperature. Based on Si-DOPA3-Fe0.6, we combined it with AgNWs to prepare Si-DOPA3-Fe0.6-AgNWs for measuring human physiological activity in real time. According to experimental results, Si-DOPA3-Fe0.6-AgNWs had a sensitivity of 4.6 and a linear response coefficient R2 of 0.999 within the 0–60% strain range, indicating good stability and sensitivity for this flexible sensor. This research not only advances the development of polysiloxanes in flexible electronic sensing but also holds promise for broad applications in medical health monitoring and human–machine interface fields, laying the foundation for next-generation smart material development.
- 11 May 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 14 (24) , 10661-10675
A mechanically robust self-healing polysiloxane via Fe 3+ -dopamine metal coordination for flexible sensors
In recent years, wearable electronic devices based on polydimethylsiloxane (PDMS) have garnered increasing attention. However, the limited mechanical strength of PDMS itself and its poor self-healing properties after prolonged use restrict its application in flexible sensors. Here, we propose a novel approach to successfully prepare a self-healing polydimethylsiloxane material (Si-DOPAx-Fey) with enhanced mechanical properties by introducing a metallic coordination network. The obtained Si-DOPAx-Fey exhibited a maximum tensile strength of 652 kPa and an elongation at break of 133%. When fracture damage occurred, Si-DOPA3-Fe0.6 achieved a self-healing efficiency of 90.3% after 8 hours of repair at room temperature. Based on Si-DOPA3-Fe0.6, we combined it with AgNWs to prepare Si-DOPA3-Fe0.6-AgNWs for measuring human physiological activity in real time. According to experimental results, Si-DOPA3-Fe0.6-AgNWs had a sensitivity of 4.6 and a linear response coefficient R2 of 0.999 within the 0–60% strain range, indicating good stability and sensitivity for this flexible sensor. This research not only advances the development of polysiloxanes in flexible electronic sensing but also holds promise for broad applications in medical health monitoring and human–machine interface fields, laying the foundation for next-generation smart material development.
- 22 April 2026
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 8 (9) , 6659-6670
High Thermal Conductivity Polymer Blend Films with Excellent Mechanical and Recyclable Properties Based on Hydrogen Bonding Interactions
- 22 April 2026
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 8 (9) , 6659-6670
High Thermal Conductivity Polymer Blend Films with Excellent Mechanical and Recyclable Properties Based on Hydrogen Bonding Interactions
- 19 February 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (20) , 12334-12350
Low-voltage-triggered rapid electrical detachment of pressure-sensitive adhesives via ion transport channels
Compared with conventional separation methods ( e.g. , light, heat, magnetic, and solvent-induced), electric field-controlled detachment of adhesive systems offers distinct practical application advantages.
- 19 February 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (20) , 12334-12350
Low-voltage-triggered rapid electrical detachment of pressure-sensitive adhesives via ion transport channels
Compared with conventional separation methods ( e.g. , light, heat, magnetic, and solvent-induced), electric field-controlled detachment of adhesive systems offers distinct practical application advantages.
- 10 January 2026
- Published by Elsevier in Journal of Colloid and Interface Science
- Vol. 709, 139870
Rapidly self-healing, highly adhesive, ionically conductive adhesives enabled by synergistic hydrogen bonding and coordination interactions
- 10 January 2026
- Published by Elsevier in Journal of Colloid and Interface Science
- Vol. 709, 139870
Rapidly self-healing, highly adhesive, ionically conductive adhesives enabled by synergistic hydrogen bonding and coordination interactions
- 13 November 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (47) , 65017-65031
Dual Effects of Heterocycles and Flexible Long Chains in Pressure-Sensitive Adhesives for Broad-Temperature-Range Flexible Applications
As an emerging interdisciplinary research frontier, flexible electronics are driving transformative innovations in next-generation electronic devices. The adhesive component, serving as a critical constituent in flexible electronic systems, is required to fulfill not only fundamental mechanical bonding requirements but also essential stress dissipation functions. Particularly during bending and folding operations of flexible screens, these adhesives prevent delamination or the warping of functional layers through instantaneous deformation recovery mechanisms. However, in extreme environments (such as high and low temperatures), these properties will be weakened. Therefore, this study synthesized pressure-sensitive adhesives (PSAs) with high-/low-temperature resistance through the copolymerization of heterocyclic monomers (IBOA/DCPA) with acrylic esters, followed by reactions with flexible curing agents (PEGDA 400/PEGDA 1000/PEA 1000). It was observed that the temperature resistance of the samples deteriorated with increasing cross-linking density. D-5@G1000-0.25 demonstrated excellent high- and low-temperature bonding performance, exhibiting a holding time exceeding 188 h at 85 °C and tack at -20 °C comparable to that at room temperature, which indicated that the addition of a heterocyclic monomer and flexible curing agent was beneficial to improve the high-/low-temperature resistance of PSA. At room temperature, all samples showed strain recovery times below 10 s after 100 cyclic stretching tests. This recovery time decreased with higher cross-linking density, reaching 0.5 s for D-20@G1000-0.25 (versus 4.0 s for D-5@G1000-0.25). In addition, excessive amounts of the flexible curing agent at -20 °C failed to reduce the PSA's strain recovery time. Instead, too much led to molecular chain entanglement or stacking, which prolonged the recovery time. The flexible curing agents with large molecular weight had more advantages in low-temperature strain recovery of adhesive because of their softer chain length. This study significantly enhances the adaptability of flexible and foldable displays under an extreme temperature environment.
- 13 November 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (47) , 65017-65031
Dual Effects of Heterocycles and Flexible Long Chains in Pressure-Sensitive Adhesives for Broad-Temperature-Range Flexible Applications
As an emerging interdisciplinary research frontier, flexible electronics are driving transformative innovations in next-generation electronic devices. The adhesive component, serving as a critical constituent in flexible electronic systems, is required to fulfill not only fundamental mechanical bonding requirements but also essential stress dissipation functions. Particularly during bending and folding operations of flexible screens, these adhesives prevent delamination or the warping of functional layers through instantaneous deformation recovery mechanisms. However, in extreme environments (such as high and low temperatures), these properties will be weakened. Therefore, this study synthesized pressure-sensitive adhesives (PSAs) with high-/low-temperature resistance through the copolymerization of heterocyclic monomers (IBOA/DCPA) with acrylic esters, followed by reactions with flexible curing agents (PEGDA 400/PEGDA 1000/PEA 1000). It was observed that the temperature resistance of the samples deteriorated with increasing cross-linking density. D-5@G1000-0.25 demonstrated excellent high- and low-temperature bonding performance, exhibiting a holding time exceeding 188 h at 85 °C and tack at -20 °C comparable to that at room temperature, which indicated that the addition of a heterocyclic monomer and flexible curing agent was beneficial to improve the high-/low-temperature resistance of PSA. At room temperature, all samples showed strain recovery times below 10 s after 100 cyclic stretching tests. This recovery time decreased with higher cross-linking density, reaching 0.5 s for D-20@G1000-0.25 (versus 4.0 s for D-5@G1000-0.25). In addition, excessive amounts of the flexible curing agent at -20 °C failed to reduce the PSA's strain recovery time. Instead, too much led to molecular chain entanglement or stacking, which prolonged the recovery time. The flexible curing agents with large molecular weight had more advantages in low-temperature strain recovery of adhesive because of their softer chain length. This study significantly enhances the adaptability of flexible and foldable displays under an extreme temperature environment.
- 16 September 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
Self-Adhesive, Highly Linear Flexible Strain Sensor Designed Using the Thermal Response Countermeasure Principle for a Wide Temperature Domain
Flexible strain sensors are of great significance in achieving high sensitivity monitoring, expanding the application scope of intelligent devices, and promoting the innovation of human-computer interaction technology. However, variations in environmental temperature frequently lead to signal drift in strain sensing, compromising the stability and accuracy of the measurements. This study exploits the negative temperature coefficient of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonic acid) (PEDOT:PSS) in its temperature response. Through constructing the network cross-linking structure, introducing hydrogen bonding, and modulating metal coordination, the thermal expansion mismatch between PEDOT:PSS and the matrix was effectively mitigated. By balancing the antagonistic effects of the "negative temperature effect" (NTC) and "thermal expansion effect" (PTC), the insensitive characteristic of the sensing material to temperature changes was achieved. The temperature coefficient of resistance (TCR) of the sample decreased from 40.29 to 0.45%/K. Meanwhile, the modified samples exhibit superior strain-sensing performance, characterized by a broad strain range of 0-50%, excellent linearity, and stable signal output, which is attributed to their self-adhesive property. These samples demonstrate exceptional stability and durability, maintaining a consistent strain-sensing signal after undergoing over 2000 stretching-recovery cycles. Consequently, this study successfully developed a temperature-insensitive flexible strain-sensing material. The sensor's temperature insensitivity and its ability to stably monitor strain emphasize its significant potential for applications in variable temperature environments, particularly in human motion monitoring and health monitoring.
- 16 September 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
Self-Adhesive, Highly Linear Flexible Strain Sensor Designed Using the Thermal Response Countermeasure Principle for a Wide Temperature Domain
Flexible strain sensors are of great significance in achieving high sensitivity monitoring, expanding the application scope of intelligent devices, and promoting the innovation of human-computer interaction technology. However, variations in environmental temperature frequently lead to signal drift in strain sensing, compromising the stability and accuracy of the measurements. This study exploits the negative temperature coefficient of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonic acid) (PEDOT:PSS) in its temperature response. Through constructing the network cross-linking structure, introducing hydrogen bonding, and modulating metal coordination, the thermal expansion mismatch between PEDOT:PSS and the matrix was effectively mitigated. By balancing the antagonistic effects of the "negative temperature effect" (NTC) and "thermal expansion effect" (PTC), the insensitive characteristic of the sensing material to temperature changes was achieved. The temperature coefficient of resistance (TCR) of the sample decreased from 40.29 to 0.45%/K. Meanwhile, the modified samples exhibit superior strain-sensing performance, characterized by a broad strain range of 0-50%, excellent linearity, and stable signal output, which is attributed to their self-adhesive property. These samples demonstrate exceptional stability and durability, maintaining a consistent strain-sensing signal after undergoing over 2000 stretching-recovery cycles. Consequently, this study successfully developed a temperature-insensitive flexible strain-sensing material. The sensor's temperature insensitivity and its ability to stably monitor strain emphasize its significant potential for applications in variable temperature environments, particularly in human motion monitoring and health monitoring.
- 1 September 2025
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 7 (17) , 11394-11403
Ultrahigh Linear Temperature Sensors Based on Poly(3,4-Ethylenedioxythiophene):Poly(Styrenesulfonate) with Negative Temperature Compensation for Wireless Temperature Monitoring
- 1 September 2025
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 7 (17) , 11394-11403
Ultrahigh Linear Temperature Sensors Based on Poly(3,4-Ethylenedioxythiophene):Poly(Styrenesulfonate) with Negative Temperature Compensation for Wireless Temperature Monitoring
- 24 July 2025
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 37 (15) , 5983-5994
High Thermal Conductivity and Recycling of Main-Chain Liquid Crystal Polyesters Based on π–π Stacking
- 24 July 2025
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 37 (15) , 5983-5994
High Thermal Conductivity and Recycling of Main-Chain Liquid Crystal Polyesters Based on π–π Stacking
- 3 April 2025
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 7 (8) , 4813-4824
Biphenyl-Based High Thermal Conductivity Films with Intrinsic Self-Healing Properties
- 3 April 2025
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 7 (8) , 4813-4824
Biphenyl-Based High Thermal Conductivity Films with Intrinsic Self-Healing Properties