Soon-An Ong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Soon-An Ong has a total of 81 co-authors. Here are the top co-authors by number of shared publications:
- Yee-Shian Wong
Faculty of Civil Engineering Technology, Universiti Malaysia Perlis, Arau, Malaysia
41 shared publications Li-Ngee Ho
Faculty of Chemical Engineering and Technology, Universiti Malaysia Perlis (UniMAP), 02600, Arau, Perlis, Malaysia
29 shared publications- Harvinder Kaur Lehl
Water Research Group (WAREG), School of Environmental Engineering, Universiti Malaysia Perlis, 02600 Arau, Perlis, Malaysia
14 shared publications - Wei-Eng Thung
Universiti Malaysia Perlis
14 shared publications - Yoong-Ling Oon
Water Research Group (WAREG), School of Environmental Engineering, Universiti Malaysia Perlis, 02600 Arau, Perlis, Malaysia
14 shared publications - Yoong-Sin Oon
Water Research Group (WAREG), School of Environmental Engineering, Universiti Malaysia Perlis, 02600 Arau, Perlis, Malaysia
12 shared publications
Latest Publications
- 1 July 2024
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 26 (30) , 20409-20426
Unravelling the kinetics, isotherms, thermodynamics, and mass transfer behaviours of Zeolite Socony Mobil - 5 in removing hydrogen sulphide resulting from a dark fermentative biohydrogen production process
Research into the speciation of sulfur and hydrogen molecules produced through the complex process of thermophilic dark fermentation has been conducted. Detailed surface studies of solid–gas systems using real biogas (biohydrogen) streams have unveiled the mechanisms and specific interactions between these gases and the physicochemical properties of a zeolite as an adsorbent. These findings highlight the potential of zeolites to effectively capture and interact with these molecules. In this study, the hydrogen sulphide removal analysis was conducted using 0.8 g of the adsorbent and at various reaction temperatures (25–125 °C), a flow rate of 100 mL min−1, and an initial concentration of approximately 5000 ppm hydrogen sulphide. The reaction temperature has been observed to be an essential parameter of Zeolite Socony Mobil - 5 adsorption capacity. The optimum adsorption capacity attains a maximum value of 0.00890 mg g−1 at an optimal temperature of 25 °C. The formation of sulphur species resulting from the hydrogen sulphide adsorption on the zeolite determines the kinetics, thermodynamics, and mass transfer behaviours of Zeolite Socony Mobil - 5 in hydrogen sulphide removal and Zeolite Socony Mobil - 5 is found to improve the quality of biohydrogen produced in thermophilic environments. Biohydrogen (raw gas) yield was enhanced from 2.48 mol H2 mol−1 hexose consumed before adsorption to 2.59 mol H2 mol−1 hexose consumed after adsorption at a temperature of 25 °C. The Avrami kinetic model was fitted for hydrogen sulphide removal on Zeolite Socony Mobil – 5. The process is explained well and fitted using the Temkin isotherm model and the investigation into thermodynamics reveals that the adsorption behaviour is exothermic and non-spontaneous. Furthermore, the gas molecule's freedom of movement becomes random. The adsorption phase is restricted by intra-particle diffusion followed by film diffusion during the transfer of hydrogen sulphide into the pores of Zeolite Socony Mobil – 5 prior to adsorption on its active sites. The utilisation of Zeolite Socony Mobil - 5 for hydrogen sulphide removal offers the benefit of reducing environmental contamination and exhibiting significant applications in industrial operations.
- 1 July 2024
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 26 (30) , 20409-20426
Unravelling the kinetics, isotherms, thermodynamics, and mass transfer behaviours of Zeolite Socony Mobil - 5 in removing hydrogen sulphide resulting from a dark fermentative biohydrogen production process
Research into the speciation of sulfur and hydrogen molecules produced through the complex process of thermophilic dark fermentation has been conducted. Detailed surface studies of solid–gas systems using real biogas (biohydrogen) streams have unveiled the mechanisms and specific interactions between these gases and the physicochemical properties of a zeolite as an adsorbent. These findings highlight the potential of zeolites to effectively capture and interact with these molecules. In this study, the hydrogen sulphide removal analysis was conducted using 0.8 g of the adsorbent and at various reaction temperatures (25–125 °C), a flow rate of 100 mL min−1, and an initial concentration of approximately 5000 ppm hydrogen sulphide. The reaction temperature has been observed to be an essential parameter of Zeolite Socony Mobil - 5 adsorption capacity. The optimum adsorption capacity attains a maximum value of 0.00890 mg g−1 at an optimal temperature of 25 °C. The formation of sulphur species resulting from the hydrogen sulphide adsorption on the zeolite determines the kinetics, thermodynamics, and mass transfer behaviours of Zeolite Socony Mobil - 5 in hydrogen sulphide removal and Zeolite Socony Mobil - 5 is found to improve the quality of biohydrogen produced in thermophilic environments. Biohydrogen (raw gas) yield was enhanced from 2.48 mol H2 mol−1 hexose consumed before adsorption to 2.59 mol H2 mol−1 hexose consumed after adsorption at a temperature of 25 °C. The Avrami kinetic model was fitted for hydrogen sulphide removal on Zeolite Socony Mobil – 5. The process is explained well and fitted using the Temkin isotherm model and the investigation into thermodynamics reveals that the adsorption behaviour is exothermic and non-spontaneous. Furthermore, the gas molecule's freedom of movement becomes random. The adsorption phase is restricted by intra-particle diffusion followed by film diffusion during the transfer of hydrogen sulphide into the pores of Zeolite Socony Mobil – 5 prior to adsorption on its active sites. The utilisation of Zeolite Socony Mobil - 5 for hydrogen sulphide removal offers the benefit of reducing environmental contamination and exhibiting significant applications in industrial operations.
- 26 June 2023
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 30 (35) , 84397-84411
Enhancement of energy recovery from caffeine wastewater in constructed wetland-microbial fuel cell through operating conditions
The enhancement of up-flow constructed wetland-microbial fuel cell (UFCW-MFC) performance in energy retrieval from caffeine containing wastewater has been explored via various operating conditions (hydraulic retention time (HRT), multianode (MA), multicathode current collector (MC), external resistance). The anaerobic decaffeination and COD removal improved by 37 and 12% as the HRT extended from 1 to 5 d. The increment in contact time between the microbes and organic substrates promoted the degradation and contributed to higher power output (3.4-fold), CE (eightfold), and NER (14–16-fold). The MA and MC connections facilitated the electron transfer rate and the degradation rate of organic substrates in the multiple anodic zones, which enhanced the removal efficiency in the anaerobic compartment (Caffeine: 4.2%; COD: 7.4%) and led to higher electricity generation (Power: 4.7-fold) and energy recovery (CE: 1.4-fold; NER: 2.3–2.5-fold) compared to SA. The lower external resistance favored the growth of electrogens and induced higher electron flux, where the best treatment performance and electricity production was obtained when the external resistance approached the internal resistance. Overall, it was noteworthy that the optimum operating conditions were achieved with 5 d HRT, MA, and MC connection along with external resistance of 200 Ω, which significantly outperformed the initial conditions (1 d HRT, SA connection, and 1000 Ω) by 43.7 and 29.8% of caffeine and COD removal in the anaerobic compartment, respectively as well as 14-fold of power generation.
- 26 June 2023
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 30 (35) , 84397-84411
Enhancement of energy recovery from caffeine wastewater in constructed wetland-microbial fuel cell through operating conditions
The enhancement of up-flow constructed wetland-microbial fuel cell (UFCW-MFC) performance in energy retrieval from caffeine containing wastewater has been explored via various operating conditions (hydraulic retention time (HRT), multianode (MA), multicathode current collector (MC), external resistance). The anaerobic decaffeination and COD removal improved by 37 and 12% as the HRT extended from 1 to 5 d. The increment in contact time between the microbes and organic substrates promoted the degradation and contributed to higher power output (3.4-fold), CE (eightfold), and NER (14–16-fold). The MA and MC connections facilitated the electron transfer rate and the degradation rate of organic substrates in the multiple anodic zones, which enhanced the removal efficiency in the anaerobic compartment (Caffeine: 4.2%; COD: 7.4%) and led to higher electricity generation (Power: 4.7-fold) and energy recovery (CE: 1.4-fold; NER: 2.3–2.5-fold) compared to SA. The lower external resistance favored the growth of electrogens and induced higher electron flux, where the best treatment performance and electricity production was obtained when the external resistance approached the internal resistance. Overall, it was noteworthy that the optimum operating conditions were achieved with 5 d HRT, MA, and MC connection along with external resistance of 200 Ω, which significantly outperformed the initial conditions (1 d HRT, SA connection, and 1000 Ω) by 43.7 and 29.8% of caffeine and COD removal in the anaerobic compartment, respectively as well as 14-fold of power generation.
- 9 May 2023
- Published by Springer Nature in Bioprocess and Biosystems Engineering
- Vol. 46 (7) , 995-1009
Exploring the potential of thermophilic anaerobic co-digestion between agro-industrial waste and water hyacinth: operational performance, kinetic study and degradation pathway
Anaerobic co-digestion (co-AD) of agro-industrial waste, namely, palm oil mill effluent (POME) and sugarcane vinasse (Vn), with water hyacinth (WH) as co-substrate was carried out in two separate Anaerobic Suspended Growth Closed Bioreactors (ASGCBs) under thermophilic (55 °C) conditions. The highest chemical oxygen demand (COD) and soluble COD reduction in co-AD of POME-WH (78.61%, 78.86%) is slightly higher than co-AD of Vn-WH (75.75%, 78.24%). However, VFA reduction in co-AD of POME-WH (96.41%) is higher compared to co-AD of Vn-WH (85.94%). Subsequently, biogas production peaked at 13438 mL/day values and 16122 mL/day for co-AD of POME-WH and Vn-WH, respectively. However, the methane content was higher in the co-AD of POME-WH (72.04%) than in the co-AD of Vn-WH (69.86%). Growth yield (YG), maximum specific substrate utilization rate (rx,max) and maximum specific biomass growth rate (μmax) are higher in co-AD of POME-WH, as supported by the higher mixed liquor volatile suspended solids (MLVSS) and COD reduction efficiency compared to co-AD of Vn-WH. However, methane yield (\({Y}_{{CH}_{4}}\)) reported in the co-AD of POME-WH and Vn-WH are 0.2748 and 0.3112 L CH4/g CODreduction, respectively, which suggests that WH is a more suitable co-substrate for Vn compared to POME. Graphical Abstract- 9 May 2023
- Published by Springer Nature in Bioprocess and Biosystems Engineering
- Vol. 46 (7) , 995-1009
Exploring the potential of thermophilic anaerobic co-digestion between agro-industrial waste and water hyacinth: operational performance, kinetic study and degradation pathway
Anaerobic co-digestion (co-AD) of agro-industrial waste, namely, palm oil mill effluent (POME) and sugarcane vinasse (Vn), with water hyacinth (WH) as co-substrate was carried out in two separate Anaerobic Suspended Growth Closed Bioreactors (ASGCBs) under thermophilic (55 °C) conditions. The highest chemical oxygen demand (COD) and soluble COD reduction in co-AD of POME-WH (78.61%, 78.86%) is slightly higher than co-AD of Vn-WH (75.75%, 78.24%). However, VFA reduction in co-AD of POME-WH (96.41%) is higher compared to co-AD of Vn-WH (85.94%). Subsequently, biogas production peaked at 13438 mL/day values and 16122 mL/day for co-AD of POME-WH and Vn-WH, respectively. However, the methane content was higher in the co-AD of POME-WH (72.04%) than in the co-AD of Vn-WH (69.86%). Growth yield (YG), maximum specific substrate utilization rate (rx,max) and maximum specific biomass growth rate (μmax) are higher in co-AD of POME-WH, as supported by the higher mixed liquor volatile suspended solids (MLVSS) and COD reduction efficiency compared to co-AD of Vn-WH. However, methane yield (\({Y}_{{CH}_{4}}\)) reported in the co-AD of POME-WH and Vn-WH are 0.2748 and 0.3112 L CH4/g CODreduction, respectively, which suggests that WH is a more suitable co-substrate for Vn compared to POME. Graphical Abstract- 4 April 2023
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 30 (21) , 59877-59890
Transformation from biofiltration unit to hybrid constructed wetland-microbial fuel cell: Improvement of wastewater treatment performance and energy recovery
- 4 April 2023
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 30 (21) , 59877-59890
Transformation from biofiltration unit to hybrid constructed wetland-microbial fuel cell: Improvement of wastewater treatment performance and energy recovery
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2712 (1) , 050003
Kinetic study of substrate inhibition on the anaerobic degradation of sugarcane vinasse
Sugarcane vinasse was utilized as a substrate in thermophilic anaerobic degradation operated at hydraulic retention time (HRT) of 35 to 15 days, corresponding to organic loading rate (OLR) of 2.14 to 5.00 kg COD/m3.day. This study focuses on the soluble chemical oxygen demand (sCOD) reduction performance, kinetic evaluation through substrate inhibition model and model selection through the Akaike information criterion (AIC). The efficiency of sCOD reduction reached 84.7 % at OLR of 2.14 kg COD/m3.day and declined significantly to 51.4 % at OLR of 5.00 kg COD/m3.day. The Solver tool in Microsoft Office Excel was used to fit experimental data to the substrate inhibition models in the evaluation of the maximum specific substrate utilization rate (rxmax), substrate saturation constant (KS) and substrate inhibition constant (Ki). Model discrimination was performed using AIC and Tessier model was selected as the best fitted model with the highest likelihood of occurrence. Kinetic evaluation through the Tessier model gives: rxmax 14.6745 /day, KS = 16.3218 and Ki = 16.9691.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2712 (1) , 050003
Kinetic study of substrate inhibition on the anaerobic degradation of sugarcane vinasse
Sugarcane vinasse was utilized as a substrate in thermophilic anaerobic degradation operated at hydraulic retention time (HRT) of 35 to 15 days, corresponding to organic loading rate (OLR) of 2.14 to 5.00 kg COD/m3.day. This study focuses on the soluble chemical oxygen demand (sCOD) reduction performance, kinetic evaluation through substrate inhibition model and model selection through the Akaike information criterion (AIC). The efficiency of sCOD reduction reached 84.7 % at OLR of 2.14 kg COD/m3.day and declined significantly to 51.4 % at OLR of 5.00 kg COD/m3.day. The Solver tool in Microsoft Office Excel was used to fit experimental data to the substrate inhibition models in the evaluation of the maximum specific substrate utilization rate (rxmax), substrate saturation constant (KS) and substrate inhibition constant (Ki). Model discrimination was performed using AIC and Tessier model was selected as the best fitted model with the highest likelihood of occurrence. Kinetic evaluation through the Tessier model gives: rxmax 14.6745 /day, KS = 16.3218 and Ki = 16.9691.
- 5 October 2022
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 30 (7) , 17546-17563
Insights into the decolorization of mono and diazo dyes in single and binary dyes containing wastewater and electricity generation in up-flow constructed wetland coupled microbial fuel cell
The treatment of single and binary azo dyes, as well as the effect of the circuit connection, aeration, and plant on the performance of UFCW-MFC, were explored in this study. The decolorization efficiency of Remazol Yellow FG (RY) (single dye: 98.2 %; binary dye: 92.3 %) was higher than Reactive Black 5 (RB5) (single: 92.3 %; binary: 86.7 %), which could be due to monoazo dye (RY) requiring fewer electrons to break the azo bond compared to the diazo dye (RB5). In contrast, the higher decolorization rate of RB5 in binary dye indicated the removal rate was affected by the electron-withdrawing groups in the dye structure. The closed circuit enhanced about 2% of color and 4% of COD removal. Aeration improved the COD removal by 6%, which could be contributed by the mineralization of intermediates. The toxicity of azo dyes was reduced by 11–26% and the degradation pathways were proposed. The dye removal by the plants was increased with a higher contact time. RB5 was more favorable to be uptook by the plant as RB5 holds a higher partial positive charge. 127.39 (RY), 125.82 (RB5), and 58.66 mW/m3 (binary) of maximum power density were generated. The lower power production in treating the binary dye could be due to more electrons being utilized for the degradation of higher dye concentration. Overall, the UFCW-MFC operated in a closed circuit, aerated, and planted conditions achieved the optimum performance in treating binary azo dyes containing wastewater (dye: 87–92%; COD: 91%) compared to the other conditions (dye: 83–92%; COD: 78–87%).
- 5 October 2022
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 30 (7) , 17546-17563
Insights into the decolorization of mono and diazo dyes in single and binary dyes containing wastewater and electricity generation in up-flow constructed wetland coupled microbial fuel cell
The treatment of single and binary azo dyes, as well as the effect of the circuit connection, aeration, and plant on the performance of UFCW-MFC, were explored in this study. The decolorization efficiency of Remazol Yellow FG (RY) (single dye: 98.2 %; binary dye: 92.3 %) was higher than Reactive Black 5 (RB5) (single: 92.3 %; binary: 86.7 %), which could be due to monoazo dye (RY) requiring fewer electrons to break the azo bond compared to the diazo dye (RB5). In contrast, the higher decolorization rate of RB5 in binary dye indicated the removal rate was affected by the electron-withdrawing groups in the dye structure. The closed circuit enhanced about 2% of color and 4% of COD removal. Aeration improved the COD removal by 6%, which could be contributed by the mineralization of intermediates. The toxicity of azo dyes was reduced by 11–26% and the degradation pathways were proposed. The dye removal by the plants was increased with a higher contact time. RB5 was more favorable to be uptook by the plant as RB5 holds a higher partial positive charge. 127.39 (RY), 125.82 (RB5), and 58.66 mW/m3 (binary) of maximum power density were generated. The lower power production in treating the binary dye could be due to more electrons being utilized for the degradation of higher dye concentration. Overall, the UFCW-MFC operated in a closed circuit, aerated, and planted conditions achieved the optimum performance in treating binary azo dyes containing wastewater (dye: 87–92%; COD: 91%) compared to the other conditions (dye: 83–92%; COD: 78–87%).
- 7 July 2022
- Published by Springer Nature in Bioprocess and Biosystems Engineering
- Vol. 46 (3) , 359-371
Intermolecular degradation of aromatic compound and its derivatives via combined sequential and hybridized process
The under-treated wastewater, especially remaining carcinogenic aromatic compounds in wastewater discharge has been expansively reported, wherein the efficiency of conventional wastewater treatment is identified as the primary contributor source. Herein, the advancement of wastewater treatments has drawn much attention in recent years. In the current study, combined sequential and hybridized treatment of thermolysis and coagulation–flocculation provides a novel advancement for environmental emerging pollutant (EP) prescription. This research is mainly demonstrating the mitigation efficiency and degradation pathway of pararosaniline (PRA) hybridized and combined sequential wastewater treatment. Notably, PRA degradation dominantly via a linkage of reaction: thermal cleavage, deamination, silication and diazene reduction. Thermolysis acts as an initiator for the PRA decomposition through thermally induced bond dissociation energy (BDE) for molecular fragmentation whilst coagulation–flocculation facilitates the formation of organo-bridged silsesquioxane as the final degradation product. Different from conventional treatment, the hybridized treatment showed excellent synergistic degradability by removing 99% PRA and its EPs, followed by combined sequential treatment method with 86% reduction. Comprehensive degradation pathway breakdown of carcinogenic and hardly degradable aromatic compounds provides a new insight for wastewater treatment whereby aniline and benzene are entirely undetectable in effluent. The degradation intermediates, reaction derivatives and end products were affirmed by gas chromatography–mass spectrometry, Fourier transform infrared spectroscopy and ultraviolet–visible spectrophotometry (GC–MS, FTIR and UV–Vis). This finding provides valuable guidance in establishing efficient integrated multiple-step wastewater treatments. Graphical abstract
- 7 July 2022
- Published by Springer Nature in Bioprocess and Biosystems Engineering
- Vol. 46 (3) , 359-371
Intermolecular degradation of aromatic compound and its derivatives via combined sequential and hybridized process
The under-treated wastewater, especially remaining carcinogenic aromatic compounds in wastewater discharge has been expansively reported, wherein the efficiency of conventional wastewater treatment is identified as the primary contributor source. Herein, the advancement of wastewater treatments has drawn much attention in recent years. In the current study, combined sequential and hybridized treatment of thermolysis and coagulation–flocculation provides a novel advancement for environmental emerging pollutant (EP) prescription. This research is mainly demonstrating the mitigation efficiency and degradation pathway of pararosaniline (PRA) hybridized and combined sequential wastewater treatment. Notably, PRA degradation dominantly via a linkage of reaction: thermal cleavage, deamination, silication and diazene reduction. Thermolysis acts as an initiator for the PRA decomposition through thermally induced bond dissociation energy (BDE) for molecular fragmentation whilst coagulation–flocculation facilitates the formation of organo-bridged silsesquioxane as the final degradation product. Different from conventional treatment, the hybridized treatment showed excellent synergistic degradability by removing 99% PRA and its EPs, followed by combined sequential treatment method with 86% reduction. Comprehensive degradation pathway breakdown of carcinogenic and hardly degradable aromatic compounds provides a new insight for wastewater treatment whereby aniline and benzene are entirely undetectable in effluent. The degradation intermediates, reaction derivatives and end products were affirmed by gas chromatography–mass spectrometry, Fourier transform infrared spectroscopy and ultraviolet–visible spectrophotometry (GC–MS, FTIR and UV–Vis). This finding provides valuable guidance in establishing efficient integrated multiple-step wastewater treatments. Graphical abstract
- 16 May 2022
- Published by Springer Nature in Chemical Papers
- Vol. 76 (9) , 5399-5410
Effect of operating temperature in the anaerobic degradation of palm oil mill effluent: Process performance, microbial community, and biokinetic evaluation
- 16 May 2022
- Published by Springer Nature in Chemical Papers
- Vol. 76 (9) , 5399-5410
Effect of operating temperature in the anaerobic degradation of palm oil mill effluent: Process performance, microbial community, and biokinetic evaluation