Jingwen Lu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Jingwen Lu has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Chaoquan Tang
School of Mechatronic Engineering, China University of Mining and Technology, Xuzhou 221116, China
2 shared publications - Eryi Hu
Information Institute, Ministry of Emergency Management of the Peoples Republic of China, Beijing, China
2 shared publications - Zhipeng Li
China Univ Min & Technol, Sch Mechatron Engn, Xuzhou, Peoples R China
1 shared publication
Latest Publications
- Open Access
- 24 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
A Shape Generation Method by Fitting Ordered Points for a Snake Robot
This paper proposes a method for a snake robot to fit ordered points and thus generate body shape. A non-smooth backbone curve consisting of straight line segments is constructed by sequentially connecting the ordered points, and then the bending and twist angles at the singularities are obtained to obtain the joint angles of the snake robot. Fitting the shape of a snake robot using this method does not depend on obtaining a backbone curve with known curvature and torsion, greatly expanding the applicability of the fitting method. In this paper, the validity of the fitting method is verified by simulation, which generates a shape for climbing on a rod with multiple forks.
- 24 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Open AccessA Shape Generation Method by Fitting Ordered Points for a Snake Robot
This paper proposes a method for a snake robot to fit ordered points and thus generate body shape. A non-smooth backbone curve consisting of straight line segments is constructed by sequentially connecting the ordered points, and then the bending and twist angles at the singularities are obtained to obtain the joint angles of the snake robot. Fitting the shape of a snake robot using this method does not depend on obtaining a backbone curve with known curvature and torsion, greatly expanding the applicability of the fitting method. In this paper, the validity of the fitting method is verified by simulation, which generates a shape for climbing on a rod with multiple forks.
- Open Access
- 18 February 2025
- Published by Wiley
Gait Design Method for a Snake Robot by Fitting a Nonsmooth Backbone Curve
This paper presents a gait design method for a snake robots fit non-smooth backbone curves. Introducing bending angles at the points where the directions of tangent vectors of the backbone curve changes discontinuously breaks the restriction that the left and right limits of tangent vectors at each point on the backbone curve fitting the target shape of the snake robot must be the same, which makes the design of the target trunk curve simpler and more convenient. The method was utilized to design gaits for spanning motions between parallel and intersecting bars. Three gaits were demonstrated in the simulation to verify the effectiveness of the fitting method.
- 18 February 2025
- Published by Wiley
Open AccessGait Design Method for a Snake Robot by Fitting a Nonsmooth Backbone Curve
This paper presents a gait design method for a snake robots fit non-smooth backbone curves. Introducing bending angles at the points where the directions of tangent vectors of the backbone curve changes discontinuously breaks the restriction that the left and right limits of tangent vectors at each point on the backbone curve fitting the target shape of the snake robot must be the same, which makes the design of the target trunk curve simpler and more convenient. The method was utilized to design gaits for spanning motions between parallel and intersecting bars. Three gaits were demonstrated in the simulation to verify the effectiveness of the fitting method.
- 2 April 2024
- Published by IOP Publishing in Bioinspiration & Biomimetics
- Vol. 19 (3) , 036010
S-shaped rolling gait designed using curve transformations of a snake robot for climbing on a bifurcated pipe
In this work, we focus on overcoming the challenge of a snake robot climbing on the outside of a bifurcated pipe. Inspired by the climbing postures of biological snakes, we propose an S-shaped rolling gait designed using curve transformations. For this gait, the snake robot’s body presenting an S-shaped curve is wrapped mainly around one side of the pipe, which leaves space for the fork of the pipe. To overcome the difficulty in constructing and clarifying the S-shaped curve, we present a method for establishing the transformation between a plane curve and a 3D curve on a cylindrical surface. Therefore, we can intuitively design the curve in 3D space, while analytically calculating the geometric properties of the curve in simple planar coordinate systems. The effectiveness of the proposed gait is verified by actual experiments. In successful configuration scenarios, the snake robot could stably climb on the pipe and efficiently cross or climb to the bifurcation while maintaining its target shape.
- 2 April 2024
- Published by IOP Publishing in Bioinspiration & Biomimetics
- Vol. 19 (3) , 036010
S-shaped rolling gait designed using curve transformations of a snake robot for climbing on a bifurcated pipe
In this work, we focus on overcoming the challenge of a snake robot climbing on the outside of a bifurcated pipe. Inspired by the climbing postures of biological snakes, we propose an S-shaped rolling gait designed using curve transformations. For this gait, the snake robot’s body presenting an S-shaped curve is wrapped mainly around one side of the pipe, which leaves space for the fork of the pipe. To overcome the difficulty in constructing and clarifying the S-shaped curve, we present a method for establishing the transformation between a plane curve and a 3D curve on a cylindrical surface. Therefore, we can intuitively design the curve in 3D space, while analytically calculating the geometric properties of the curve in simple planar coordinate systems. The effectiveness of the proposed gait is verified by actual experiments. In successful configuration scenarios, the snake robot could stably climb on the pipe and efficiently cross or climb to the bifurcation while maintaining its target shape.