Qing Gao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Qing Gao has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
Jisen Qiao
5 shared publicationsJunqiang Ren
5 shared publicationsXuefeng Lu
5 shared publicationsBiao Sang
4 shared publicationsQi Wang
4 shared publicationsQilun Li
3 shared publications
Latest Publications
- 17 May 2025
- Published by World Scientific Pub Co Pte Ltd in Nano
- Vol. 21 (04)
Atomic-Scale Study on the Dislocation Evolution Mechanism of Al/Cu-Layered Materials Under Nanoindentation
Al/Cu-layered metal materials, a kind of material with a highly ordered structure and excellent comprehensive performance, are widely used in the fields of automobile, aerospace and shipbuilding. The molecular dynamics method was adopted to simulate the mechanical behavior and dislocation evolution mechanism of Al/Cu-layered materials at different indentation velocities; the results indicating the uniquely periodic dislocation network formed during deformation at the interface can prevent further dislocation slip and relieve stress concentration, leading to the improvement of the strength and hardness. The interface dislocation can be activated when the indentation depth is sufficient, along with the location and slip system, depending on the symmetry of the crystal structure and the Schmidt factor. Moreover, the plastic deformation begins with the nucleation and movement of Shockley partial dislocations and is dominated by the dislocation slip. With the increase of indentation velocity, the movement and reaction of dislocations are promoted, which have an emergence of immobile dislocations, complex dislocation loops, many dislocation tangles and limited dislocation cross-slip, greatly accelerating the work hardening and delaying the deformation. Particularly, there are two main steps in the formation of independent prismatic dislocation loops. First, multiple “u”-type dislocation loops nucleate and then slip. Second, the screw dislocation fragments of the shear dislocation loop cross-slip on the intersecting [ ] slip plane. The research results open a window in manufacturing nanoprecision devices, analyzing the service performance and carrying out reliability evaluation.
- 17 May 2025
- Published by World Scientific Pub Co Pte Ltd in Nano
- Vol. 21 (04)
Atomic-Scale Study on the Dislocation Evolution Mechanism of Al/Cu-Layered Materials Under Nanoindentation
Al/Cu-layered metal materials, a kind of material with a highly ordered structure and excellent comprehensive performance, are widely used in the fields of automobile, aerospace and shipbuilding. The molecular dynamics method was adopted to simulate the mechanical behavior and dislocation evolution mechanism of Al/Cu-layered materials at different indentation velocities; the results indicating the uniquely periodic dislocation network formed during deformation at the interface can prevent further dislocation slip and relieve stress concentration, leading to the improvement of the strength and hardness. The interface dislocation can be activated when the indentation depth is sufficient, along with the location and slip system, depending on the symmetry of the crystal structure and the Schmidt factor. Moreover, the plastic deformation begins with the nucleation and movement of Shockley partial dislocations and is dominated by the dislocation slip. With the increase of indentation velocity, the movement and reaction of dislocations are promoted, which have an emergence of immobile dislocations, complex dislocation loops, many dislocation tangles and limited dislocation cross-slip, greatly accelerating the work hardening and delaying the deformation. Particularly, there are two main steps in the formation of independent prismatic dislocation loops. First, multiple “u”-type dislocation loops nucleate and then slip. Second, the screw dislocation fragments of the shear dislocation loop cross-slip on the intersecting [ ] slip plane. The research results open a window in manufacturing nanoprecision devices, analyzing the service performance and carrying out reliability evaluation.
- 10 January 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 924
In-situ study of dislocation coordinated plastic deformation mechanism in as-cast Ni33Co40Mn27 medium entropy alloy
- 10 January 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 924
In-situ study of dislocation coordinated plastic deformation mechanism in as-cast Ni33Co40Mn27 medium entropy alloy
- 26 July 2024
- Published by Elsevier in Journal of Materials Science & Technology
- Vol. 215, 71-85
Optimizing strength-ductility in NiCoMn medium entropy alloys with atomic-scale rapid composition design
- 26 July 2024
- Published by Elsevier in Journal of Materials Science & Technology
- Vol. 215, 71-85
Optimizing strength-ductility in NiCoMn medium entropy alloys with atomic-scale rapid composition design
- 10 June 2024
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 26 (24) , 17240-17254
The first-principles study of interfacial bonding strength and segregation behavior of alloyed elements at the η(MgZn 2 )/Al interface
For precipitation-strengthened Al alloys, the interfacial segregation behavior of alloying elements plays an important role in controlling the effectiveness of precipitation strengthening. In this work, the adhesion work (Wad) and interfacial energy (γ) of the η(0001)/Al(111) interface were studied to gain an insight into the interface properties between the precipitate η and the Al matrix. Additionally, we examined the impact of the segregation behavior of alloyed elements on the bonding strength of the interface. The computed values for Wad and interfacial energies indicated that the T6S3 terminated configuration represents the interfacial structure with the highest stability across all models analyzed. Focusing on the T6S3 interface, the assessed segregated energies (Eseg) disclose that the segregation ability of elements from strong to weak exhibits the order of Ti > Sc > Zr > Y > Ta > Nb > Lu > Hf > Mo > V > W, while Cr and Mn elements are not easy to segregate at the interface. Sc, Ti, V, Cr, Mn, Zr, Nb, Mo, Hf, and Ta preferentially occupy Al atoms, whereas Y and Lu predominantly inhabit Mg atoms. Relative to the clean interface, the electron cloud enrichment at the interface after alloying element X (Zr, Sc, Ti, W, Hf, Mn, Y, Lu and V) doping is weakened, and the ion interaction among interface atoms is enhanced. After doping alloying element X (Nb, Mo, Ta, and Cr), the degree of electron cloud enrichment at the interface is obviously enhanced, and the covalent interaction among interface atoms is enhanced. This suggests that the introduction of alloyed elements through doping can augment the bond strength at the interface between the precipitated phase and matrix, thereby reinforcing the strength and toughness of 7xxx series alloys.
- 10 June 2024
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 26 (24) , 17240-17254
The first-principles study of interfacial bonding strength and segregation behavior of alloyed elements at the η(MgZn 2 )/Al interface
For precipitation-strengthened Al alloys, the interfacial segregation behavior of alloying elements plays an important role in controlling the effectiveness of precipitation strengthening. In this work, the adhesion work (Wad) and interfacial energy (γ) of the η(0001)/Al(111) interface were studied to gain an insight into the interface properties between the precipitate η and the Al matrix. Additionally, we examined the impact of the segregation behavior of alloyed elements on the bonding strength of the interface. The computed values for Wad and interfacial energies indicated that the T6S3 terminated configuration represents the interfacial structure with the highest stability across all models analyzed. Focusing on the T6S3 interface, the assessed segregated energies (Eseg) disclose that the segregation ability of elements from strong to weak exhibits the order of Ti > Sc > Zr > Y > Ta > Nb > Lu > Hf > Mo > V > W, while Cr and Mn elements are not easy to segregate at the interface. Sc, Ti, V, Cr, Mn, Zr, Nb, Mo, Hf, and Ta preferentially occupy Al atoms, whereas Y and Lu predominantly inhabit Mg atoms. Relative to the clean interface, the electron cloud enrichment at the interface after alloying element X (Zr, Sc, Ti, W, Hf, Mn, Y, Lu and V) doping is weakened, and the ion interaction among interface atoms is enhanced. After doping alloying element X (Nb, Mo, Ta, and Cr), the degree of electron cloud enrichment at the interface is obviously enhanced, and the covalent interaction among interface atoms is enhanced. This suggests that the introduction of alloyed elements through doping can augment the bond strength at the interface between the precipitated phase and matrix, thereby reinforcing the strength and toughness of 7xxx series alloys.
- 28 December 2023
- Published by World Scientific Pub Co Pte Ltd in Modern Physics Letters B
- Vol. 38 (19)
Dislocation-based mechanical responses and deformation mechanisms of Al/Cu heterointerfaces: A computational study via molecular dynamics simulations
Layered metal composites have been widely used in various industries fields because of their excellent properties and are responsible for mechanical behavior of materials. This paper focuses on analyzing the deformation mechanism of the (110) interface under different loading states by MD. The results show that there are two yield points in the stress–strain curve under both Z- and Y-axis loading states. The first yield is the nucleation of dislocations at the interface, meantime the slip of dislocations and the extension of stacking faults begin at the Al layer. The second one, the dislocation passes through the interface, nucleates and emits toward the Cu layer at the interface, leading to a stress mutation. It is worth noting that during the stable rheological stage, the deformation mechanisms vary under different loading directions. Under Y-axis tensile loading, the phase transformation of FCC–HCP is present due to the interaction of dislocation movement and stacking fault. On the contrary, there are two twin paths A and B, improving the strength, during Z-axis compression loading. For other loading modes, there are three zones, namely the elastic stage, the release of energy, and strain hardening and dynamic softening. The interface plays the role of nucleation, annihilation and penetration of dislocations, and this interface-dislocation mechanism is reflected in the whole stage of plastic deformation. The results have an insight into the design and control in heterointerface.
- 28 December 2023
- Published by World Scientific Pub Co Pte Ltd in Modern Physics Letters B
- Vol. 38 (19)
Dislocation-based mechanical responses and deformation mechanisms of Al/Cu heterointerfaces: A computational study via molecular dynamics simulations
Layered metal composites have been widely used in various industries fields because of their excellent properties and are responsible for mechanical behavior of materials. This paper focuses on analyzing the deformation mechanism of the (110) interface under different loading states by MD. The results show that there are two yield points in the stress–strain curve under both Z- and Y-axis loading states. The first yield is the nucleation of dislocations at the interface, meantime the slip of dislocations and the extension of stacking faults begin at the Al layer. The second one, the dislocation passes through the interface, nucleates and emits toward the Cu layer at the interface, leading to a stress mutation. It is worth noting that during the stable rheological stage, the deformation mechanisms vary under different loading directions. Under Y-axis tensile loading, the phase transformation of FCC–HCP is present due to the interaction of dislocation movement and stacking fault. On the contrary, there are two twin paths A and B, improving the strength, during Z-axis compression loading. For other loading modes, there are three zones, namely the elastic stage, the release of energy, and strain hardening and dynamic softening. The interface plays the role of nucleation, annihilation and penetration of dislocations, and this interface-dislocation mechanism is reflected in the whole stage of plastic deformation. The results have an insight into the design and control in heterointerface.