A. A. Teplov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
A. A. Teplov has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Alexander I. Buzin
Enikolopov Institute of Synthetic Polymeric Materials of Russian Academy of Science, Profsoyuznaya st. 70, 117393 Moscow, Russian Federation
2 shared publications E. A. Golovkova
Joint Institute for High Temperatures, Russian Academy of Sciences, Moscow, Russia
2 shared publicationsE. K. Golubev
Enikolopov Institute of Synthetic Polymeric Materials, Russian Academy of Sciences, Moscow, Russia
2 shared publicationsP. V. Dmitryakov
National Research Centre “Kurchatov Institute”, Moscow, Russia
2 shared publicationsS. I. Belousov
National Research Centre “Kurchatov Institute”, Moscow, Russia
2 shared publicationsS. V. Krasheninnikov
National Research Centre “Kurchatov Institute”, Moscow, Russia
2 shared publications
Latest Publications
- 1 December 2023
- Published by Pleiades Publishing Ltd in Crystallography Reports
- Vol. 68 (7) , 1245-1253
Tribological Properties of Compositions Prepared by In Situ Polymerization, Based on Ultrahigh Molecular-Weight Polyethylene and Quasicrystalline Al–Cu–Fe
Samples of composites of ultra-high molecular-weight polyethylene (UHMWPE) with addition of 2.24, 5, and 8.1 wt % quasicrystalline Al–Cu–Fe alloy have been prepared by in situ polymerization. Friction and wear tests are performed, the physico-mechanical tensile properties are studied, and the thermophysical properties are investigated using differential scanning calorimetry and thermogravimetric analysis. The surface morphology of composite samples, both subjected and not subjected to friction, has been investigated by scanning electron microscopy. It is found that addition of a quasicrystalline Al–Cu–Fe filler in amount of 2.24 wt % improves the tribological characteristics of UHMWPE: under a load of 50 N and at friction duration of 8 h, the wear decreases by a factor of 3, and the friction coefficient decreases by 20%.
- 1 December 2023
- Published by Pleiades Publishing Ltd in Crystallography Reports
- Vol. 68 (7) , 1245-1253
Tribological Properties of Compositions Prepared by In Situ Polymerization, Based on Ultrahigh Molecular-Weight Polyethylene and Quasicrystalline Al–Cu–Fe
Samples of composites of ultra-high molecular-weight polyethylene (UHMWPE) with addition of 2.24, 5, and 8.1 wt % quasicrystalline Al–Cu–Fe alloy have been prepared by in situ polymerization. Friction and wear tests are performed, the physico-mechanical tensile properties are studied, and the thermophysical properties are investigated using differential scanning calorimetry and thermogravimetric analysis. The surface morphology of composite samples, both subjected and not subjected to friction, has been investigated by scanning electron microscopy. It is found that addition of a quasicrystalline Al–Cu–Fe filler in amount of 2.24 wt % improves the tribological characteristics of UHMWPE: under a load of 50 N and at friction duration of 8 h, the wear decreases by a factor of 3, and the friction coefficient decreases by 20%.
- 1 November 2021
- Published by Pleiades Publishing Ltd in Crystallography Reports
- Vol. 66 (6) , 883-896
Tribological, Physicomechanical, and Other Properties of Composites Based on Ultra-High Molecular-Weight Polyethylene, Polytetrafluoroethylene, and Еthylene–Tetrafluoroethylene Copolymer with Quasicrystalline Filler Al–Cu–Fe
An urgent problem in improving polymer-based tribotechnical materials is to reduce the friction and wear coefficients with preservation of sufficiently high physicomechanical characteristics of material. This review covers the studies devoted to the preparation and analysis of tribological, deformation-strength, and thermophysical properties, as well as the structure and morphology of composites based on polymer matrices of ultra-high molecular-weight polyethylene (UHMWPE), polytetrafluoroethylene, and ethylene– tetrafluoroethylene copolymer, filled with quasicrystalline (QC) Al–Cu–Fe powder, which were carried out at the National Research Centre “Kurchatov Institute.” These studies were aimed at obtaining and analyzing information in order to gain a deeper insight into the processes occurring in materials subjected to friction and search for promising combinations of materials in the matrix–filler pair. Good prospects of application of QC Al–Cu–Fe powder as a filler are justified.
- 1 November 2021
- Published by Pleiades Publishing Ltd in Crystallography Reports
- Vol. 66 (6) , 883-896
Tribological, Physicomechanical, and Other Properties of Composites Based on Ultra-High Molecular-Weight Polyethylene, Polytetrafluoroethylene, and Еthylene–Tetrafluoroethylene Copolymer with Quasicrystalline Filler Al–Cu–Fe
An urgent problem in improving polymer-based tribotechnical materials is to reduce the friction and wear coefficients with preservation of sufficiently high physicomechanical characteristics of material. This review covers the studies devoted to the preparation and analysis of tribological, deformation-strength, and thermophysical properties, as well as the structure and morphology of composites based on polymer matrices of ultra-high molecular-weight polyethylene (UHMWPE), polytetrafluoroethylene, and ethylene– tetrafluoroethylene copolymer, filled with quasicrystalline (QC) Al–Cu–Fe powder, which were carried out at the National Research Centre “Kurchatov Institute.” These studies were aimed at obtaining and analyzing information in order to gain a deeper insight into the processes occurring in materials subjected to friction and search for promising combinations of materials in the matrix–filler pair. Good prospects of application of QC Al–Cu–Fe powder as a filler are justified.