George. C. Bandlamudi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
George. C. Bandlamudi has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Angela Kruth
Materials for Energy Technology Leibniz Institute for Plasma Science and Technology Felix‐Hausdorf‐Str. 2 17489 Greifswald Germany
1 shared publication - Angelika Heinzel
University of Duisburg-Essen, LET
1 shared publication Jens Wartmann
Department of New Materials Zentrum für Brennstoffzellen Technik Center for Fuel Cell Technology Carl‐Benz‐Strasse 201 47057 Duisburg Germany
1 shared publication- Laurence Noel Warr
University of Greifswald
1 shared publication - Marcel Wetegrove
Department of Materials for Energy Technology, Leibniz Institute for Plasma Science and Technology (INP)
1 shared publication Michael Steffen
ZBT GmbH
1 shared publication
Latest Publications
- 5 January 2024
- Published by Wiley in Energy Technology
- Vol. 13 (2)
Fine Gas Purification Approaches for High Purity Hydrogen Production from Ammonia
This review aims to evaluate the state‐of‐the‐art in purifying hydrogen from green ammonia. Green ammonia contains 17.8% of H2 and enables efficient liquid storage and transport of hydrogen produced from renewable electricity. Back‐conversion of ammonia to hydrogen may be carried out by several routes, whereby thermal ammonia cracking is one of the most efficient approaches. In the conversion of ammonia at high pressures, it is only possible to achieve complete conversion at very high temperatures (≈800 °C). Therefore, the separation of ammonia in the low percentage range (e.g., 2 (from NH3), fine purity must be achieved, in agreement with ISO 14687‐2. In such a context, ammonia is particularly important, with a permissible concentration of 0.100 ppm. The main feasible routes for ultrafine purification are presented, namely, 1) permeation membranes and 2) absorbents, as well as a third route via 3) biological scrubber, and discussed with regard to efficiency, availability, and cost. Current technology gaps are also identified and an outlook is given toward new innovative approaches.
- 5 January 2024
- Published by Wiley in Energy Technology
- Vol. 13 (2)
Fine Gas Purification Approaches for High Purity Hydrogen Production from Ammonia
This review aims to evaluate the state‐of‐the‐art in purifying hydrogen from green ammonia. Green ammonia contains 17.8% of H2 and enables efficient liquid storage and transport of hydrogen produced from renewable electricity. Back‐conversion of ammonia to hydrogen may be carried out by several routes, whereby thermal ammonia cracking is one of the most efficient approaches. In the conversion of ammonia at high pressures, it is only possible to achieve complete conversion at very high temperatures (≈800 °C). Therefore, the separation of ammonia in the low percentage range (e.g., 2 (from NH3), fine purity must be achieved, in agreement with ISO 14687‐2. In such a context, ammonia is particularly important, with a permissible concentration of 0.100 ppm. The main feasible routes for ultrafine purification are presented, namely, 1) permeation membranes and 2) absorbents, as well as a third route via 3) biological scrubber, and discussed with regard to efficiency, availability, and cost. Current technology gaps are also identified and an outlook is given toward new innovative approaches.
- 15 July 2015
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2015-03 (3) , 644
Internal Reforming Methanol Fuel Cell Development
Methanol is a liquid fuel which could also be produced from renewable energy sources and has appreciably high energy density. It has a high H : C ratio of 4 : 1 without any C-C bond. It is easier to reform when compared to CH4 to produce H2 rich gas that could be fed into a high temperature polymer electrolyte membrane fuel cell or HT-PEMFC. A typical IRMFC module consists of a HT-PEMFC thermally integrated with a methanol evaporator and reformer in a closed thermal loop. Simulations show that the total heat demand of the evaporator and the methanol steam reformer would require only 20% of the heat generated by the HT-PEMFC where the geometrical area of the HT-PEMFC is almost equal to that of the geometrical area of the reforming catalyst. In the current work a novel IRMFC which is operated in the 210-220°C range is presented. Operating an IRMFC at these high temperatures would mean novel materials and components to be employed within the HT-PEMFC as well as within the methanol reformer unit. The high temperature stable membrane electrode assemblies were developed by Advent technologies in Greece. The high temperature stable bipolar plates were developed by ZBT in Germany within the scope of a current EU funded project. When operated at 220°C on 350 mA/cm² of load current, the novel HT-PEMFC could deliver 210 mW/cm² at 0.6 V. As for the methanol reforming unit operated at 220°C, when fed with methanol-water mixture with a steam to carbon ratio of 1.5, the methanol conversion rate was around 90%. The performance analyses of the IRMFC single unit as well as that of the 5 cell unit demonstrate the potential to developing a compact light weight power generating unit offering double the gravimetric and volumetric energy densities offered by the current direct methanol fuel cell based units.
- 15 July 2015
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2015-03 (3) , 644
Internal Reforming Methanol Fuel Cell Development
Methanol is a liquid fuel which could also be produced from renewable energy sources and has appreciably high energy density. It has a high H : C ratio of 4 : 1 without any C-C bond. It is easier to reform when compared to CH4 to produce H2 rich gas that could be fed into a high temperature polymer electrolyte membrane fuel cell or HT-PEMFC. A typical IRMFC module consists of a HT-PEMFC thermally integrated with a methanol evaporator and reformer in a closed thermal loop. Simulations show that the total heat demand of the evaporator and the methanol steam reformer would require only 20% of the heat generated by the HT-PEMFC where the geometrical area of the HT-PEMFC is almost equal to that of the geometrical area of the reforming catalyst. In the current work a novel IRMFC which is operated in the 210-220°C range is presented. Operating an IRMFC at these high temperatures would mean novel materials and components to be employed within the HT-PEMFC as well as within the methanol reformer unit. The high temperature stable membrane electrode assemblies were developed by Advent technologies in Greece. The high temperature stable bipolar plates were developed by ZBT in Germany within the scope of a current EU funded project. When operated at 220°C on 350 mA/cm² of load current, the novel HT-PEMFC could deliver 210 mW/cm² at 0.6 V. As for the methanol reforming unit operated at 220°C, when fed with methanol-water mixture with a steam to carbon ratio of 1.5, the methanol conversion rate was around 90%. The performance analyses of the IRMFC single unit as well as that of the 5 cell unit demonstrate the potential to developing a compact light weight power generating unit offering double the gravimetric and volumetric energy densities offered by the current direct methanol fuel cell based units.