Okan Ilhan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Okan Ilhan has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
Ellen M Rathje
Fariborz Maseeh Department of Civil, Architectural and Environmental Engineering, The University of Texas at Austin, Austin, TX, USA
2 shared publications- Gamze Muratoğlu
Civil Engineering Department, Middle East Technical University, Ankara, Türkiye
2 shared publications - Jonathan P. Stewart
Univ. of California, Los Angeles
2 shared publications Youssef Ma Hashash
Department of Civil & Environmental Engineering, University of Illinois Urbana-Champaign, Urbana, IL, USA
2 shared publicationsAbdullah Can Zülfikar
Istanbul Technical University: Istanbul Teknik Universitesi
1 shared publication- Abdullah İçEn
Munzur University, Faculty of Engineering
1 shared publication
Latest Publications
- Open Access
- 5 October 2026
- Published by Wiley in Earthquake Spectra
- Vol. 42 (4) , e70123
Simulation‐Based Nonlinear Site Amplification Models for Western United States
This article presents one of the first nonlinear (NL) site amplification models relative to V S30 of 800 m/s for the Western United States (WUS) for both the smoothed effective amplitude spectrum (EAS), described as the orientation‐independent horizontal‐component Fourier amplitude spectrum (FAS) of ground acceleration, and the response spectra ( R S ). The amplification models were derived from a total of 286,254 1D site response analyses using randomizations of base‐case V S profiles, generated through a new slowness model developed using V S measurements at California, and 600 recorded ground‐motion pairs, scaled to match target spectra for 12 earthquake scenarios. The use of slowness model for generating V S randomizations yields a far broader suite of site conditions than from the preceding study employing only eight generic profiles. The simulation‐based EAS‐ and RS‐based NL amplification data exhibits more continuous behavior and alleviates the data sparsity in the low (r (peak ground acceleration at V S30 = 800 m/s) range as compared with prior work. Four NL mean amplification models with corresponding standard deviation relationships are proposed: two EAS‐based named as N1 EAS ( V S30 , EAS r at 5 Hz), and N2 EAS ( V S30 , frequency‐specific EAS r ), and two RS‐based models as N1 RS ( V S30 , PGA r ) and N2 RS ( V S30 , pseudo‐spectral acceleration at V S30 = 800 m/s (PSA r )). The N2 relationships exhibit lower standard deviation values of the residuals compared with their N1 counterparts. The compatibility between NL models’ predictions and observed NL amplification was assessed by incorporating NL relationships into an empirical ground motion model (GMM), resulting in within‐event residuals of GMM closer to zero relative to those of GMM without NL terms, particularly for sites with 200 m/s < V S30 < 500 m/s. The amplification models are applicable for sites with V S30 ≥ 200 m/s and motions with PGA r ≤ 1.0 g or EAS r ≤ 0.3 g/s.
- 5 October 2026
- Published by Wiley in Earthquake Spectra
- Vol. 42 (4) , e70123
Open AccessSimulation‐Based Nonlinear Site Amplification Models for Western United States
This article presents one of the first nonlinear (NL) site amplification models relative to V S30 of 800 m/s for the Western United States (WUS) for both the smoothed effective amplitude spectrum (EAS), described as the orientation‐independent horizontal‐component Fourier amplitude spectrum (FAS) of ground acceleration, and the response spectra ( R S ). The amplification models were derived from a total of 286,254 1D site response analyses using randomizations of base‐case V S profiles, generated through a new slowness model developed using V S measurements at California, and 600 recorded ground‐motion pairs, scaled to match target spectra for 12 earthquake scenarios. The use of slowness model for generating V S randomizations yields a far broader suite of site conditions than from the preceding study employing only eight generic profiles. The simulation‐based EAS‐ and RS‐based NL amplification data exhibits more continuous behavior and alleviates the data sparsity in the low (r (peak ground acceleration at V S30 = 800 m/s) range as compared with prior work. Four NL mean amplification models with corresponding standard deviation relationships are proposed: two EAS‐based named as N1 EAS ( V S30 , EAS r at 5 Hz), and N2 EAS ( V S30 , frequency‐specific EAS r ), and two RS‐based models as N1 RS ( V S30 , PGA r ) and N2 RS ( V S30 , pseudo‐spectral acceleration at V S30 = 800 m/s (PSA r )). The N2 relationships exhibit lower standard deviation values of the residuals compared with their N1 counterparts. The compatibility between NL models’ predictions and observed NL amplification was assessed by incorporating NL relationships into an empirical ground motion model (GMM), resulting in within‐event residuals of GMM closer to zero relative to those of GMM without NL terms, particularly for sites with 200 m/s < V S30 < 500 m/s. The amplification models are applicable for sites with V S30 ≥ 200 m/s and motions with PGA r ≤ 1.0 g or EAS r ≤ 0.3 g/s.
- Open Access
- 22 January 2026
- Published by Springer Nature in Research Square
A Unified Evaluation of Liquefaction Triggering via Effective-Stress Site Response Analysis and Seismic Hazard: A Case Study from the 2023 Türkiye Earthquakes
Liquefaction-induced hazard at the Saadet Yusuf Mıstıkoğlu (SYM) school in Antakya (Hatay) during the 6 February 2023 Türkiye earthquakes provide an unique case study to evaluate (i) liquefaction triggering through pore-water-pressure (PWP) generation in one-dimensional (1D) effective-stress nonlinear (NL) site response analysis (SRA), which advances beyond standard 1D total-stress assessments, and (ii) site-specific seismic hazard using an event-based deterministic seismic hazard analysis (DSHA) including near-fault effects. The SYM site is underlain by a very soft and deep soil column, with reference V S condition of 760 m/s reached at ~ 560 m. Strong-motion records from the closest rock/rock-like stations were deconvolved to the half-space horizon beneath the site and used as input to 1D equivalent-linear (EL) and NL SRA. EL simulations produced unrealistically high pseudo-spectral accelerations (PSA) near the fundamental period due to large strains, confirming the need for NL modeling. NL results indicate that Turkish Building Earthquake Code (TBEC, 2019) DD-1 (2% probability of exceedance) and DD-2 (10% probability of exceedance) spectra cover NL spectra for periods ≲ 1.0 s, whereas for periods ≳ 1.5 s the computed PSA values from NL approach or slightly surpass DD-1; the event-based DSHA better captures this long-period amplification. Effective-stress analyses yield PWP-ratio (r u ) ≈ 1.0 in the deeper sand layer, consistent with liquefaction observations, while the shallower sand layer remains below r u = 1.0 because energy dissipation at depth reduces cyclic demand above. The study links observed field performance to a reproducible workflow combining PWP-based 1D analysis with DSHA for deep soft sites.
- 22 January 2026
- Published by Springer Nature in Research Square
Open AccessA Unified Evaluation of Liquefaction Triggering via Effective-Stress Site Response Analysis and Seismic Hazard: A Case Study from the 2023 Türkiye Earthquakes
Liquefaction-induced hazard at the Saadet Yusuf Mıstıkoğlu (SYM) school in Antakya (Hatay) during the 6 February 2023 Türkiye earthquakes provide an unique case study to evaluate (i) liquefaction triggering through pore-water-pressure (PWP) generation in one-dimensional (1D) effective-stress nonlinear (NL) site response analysis (SRA), which advances beyond standard 1D total-stress assessments, and (ii) site-specific seismic hazard using an event-based deterministic seismic hazard analysis (DSHA) including near-fault effects. The SYM site is underlain by a very soft and deep soil column, with reference V S condition of 760 m/s reached at ~ 560 m. Strong-motion records from the closest rock/rock-like stations were deconvolved to the half-space horizon beneath the site and used as input to 1D equivalent-linear (EL) and NL SRA. EL simulations produced unrealistically high pseudo-spectral accelerations (PSA) near the fundamental period due to large strains, confirming the need for NL modeling. NL results indicate that Turkish Building Earthquake Code (TBEC, 2019) DD-1 (2% probability of exceedance) and DD-2 (10% probability of exceedance) spectra cover NL spectra for periods ≲ 1.0 s, whereas for periods ≳ 1.5 s the computed PSA values from NL approach or slightly surpass DD-1; the event-based DSHA better captures this long-period amplification. Effective-stress analyses yield PWP-ratio (r u ) ≈ 1.0 in the deeper sand layer, consistent with liquefaction observations, while the shallower sand layer remains below r u = 1.0 because energy dissipation at depth reduces cyclic demand above. The study links observed field performance to a reproducible workflow combining PWP-based 1D analysis with DSHA for deep soft sites.
- Open Access
- 19 June 2025
- Published by Wiley in Earthquake Spectra
- Vol. 41 (4) , 3190-3212
Artificial neural network−based simulated site amplification models for Central and Eastern North America
This article explores the use of deep learning/artificial neural network (ANN)-based response spectrum (RS) and Fourier amplitude spectrum (FAS) site amplification models along with their standard deviations for simulated one-dimensional (1D) site response in Central and Eastern North America (CENA) using over 3.6 million 1D site response simulations. ANNs are demonstrated to significantly decrease the bias in the estimations (e.g. standard deviation of models’ residuals) and to better capture the features of site-specific amplification (e.g. the attributes of peak amplification) as compared to their conventional statistical regression counterparts that were derived from the same simulated amplification data. This improved performance includes site responses at shallow sites, which have been a challenge to effectively model previously. Multiple ANN models, each with different input variables but using the same ANN structure, are explored to represent diverse simulated amplification datasets (e.g. linear vs nonlinear or RS vs FAS), demonstrating beneficial features of ANN approach. In addition, ANN-based models are found to be useful in identifying controlling parameters and the minimum levels of site-to-site variability that are achievable given the conditioning variables.
- 19 June 2025
- Published by Wiley in Earthquake Spectra
- Vol. 41 (4) , 3190-3212
Open AccessArtificial neural network−based simulated site amplification models for Central and Eastern North America
This article explores the use of deep learning/artificial neural network (ANN)-based response spectrum (RS) and Fourier amplitude spectrum (FAS) site amplification models along with their standard deviations for simulated one-dimensional (1D) site response in Central and Eastern North America (CENA) using over 3.6 million 1D site response simulations. ANNs are demonstrated to significantly decrease the bias in the estimations (e.g. standard deviation of models’ residuals) and to better capture the features of site-specific amplification (e.g. the attributes of peak amplification) as compared to their conventional statistical regression counterparts that were derived from the same simulated amplification data. This improved performance includes site responses at shallow sites, which have been a challenge to effectively model previously. Multiple ANN models, each with different input variables but using the same ANN structure, are explored to represent diverse simulated amplification datasets (e.g. linear vs nonlinear or RS vs FAS), demonstrating beneficial features of ANN approach. In addition, ANN-based models are found to be useful in identifying controlling parameters and the minimum levels of site-to-site variability that are achievable given the conditioning variables.
- Open Access
- 30 May 2025
- Published by Springer Nature in Bulletin of Earthquake Engineering
- Vol. 23 (9) , 3569-3587
An initial velocity model based on VS30 for the region affected by the February 6, 2023 Turkiye earthquakes
This paper presents a VS30-dependent one-dimensional (1D) velocity model for the region affected by the February 6, 2023, earthquakes in Turkiye, which were marked by complex fault interactions along the East Anatolian Fault Zone. The proposed model utilizes VS measurements from 118 strong ground motion stations to develop a shallow VS structure (≤ 0.1 km), integrates deeper VS data from Acarel et al. (2019), and establishes a VS transition zone for intermediate depths (0.1 km to 0.6 km). The model evaluation indicated minimal bias despite some discrepancies. Additionally, compressional wave velocities (VP) and densities (ρ) corresponding to the VS30-conditioned VS model are provided. The findings from this study can be applied in a range of disciplines, including geotechnical and structural engineering, as well as ground motion simulations.
- 30 May 2025
- Published by Springer Nature in Bulletin of Earthquake Engineering
- Vol. 23 (9) , 3569-3587
Open AccessAn initial velocity model based on VS30 for the region affected by the February 6, 2023 Turkiye earthquakes
This paper presents a VS30-dependent one-dimensional (1D) velocity model for the region affected by the February 6, 2023, earthquakes in Turkiye, which were marked by complex fault interactions along the East Anatolian Fault Zone. The proposed model utilizes VS measurements from 118 strong ground motion stations to develop a shallow VS structure (≤ 0.1 km), integrates deeper VS data from Acarel et al. (2019), and establishes a VS transition zone for intermediate depths (0.1 km to 0.6 km). The model evaluation indicated minimal bias despite some discrepancies. Additionally, compressional wave velocities (VP) and densities (ρ) corresponding to the VS30-conditioned VS model are provided. The findings from this study can be applied in a range of disciplines, including geotechnical and structural engineering, as well as ground motion simulations.
- 5 February 2024
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 178
Local site effects at the selected stations affected by the February 6 2023 Türkiye Earthquake Sequences
- 5 February 2024
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 178
Local site effects at the selected stations affected by the February 6 2023 Türkiye Earthquake Sequences
- Open Access
- 1 February 2024
- Published by Wiley in Earthquake Spectra
- Vol. 40 (1) , 200-229
Simulated site amplification for Central and Eastern North America: Data set development and amplification models
This article presents a suite of response spectrum (RS) and Fourier amplitude spectrum (FAS) site amplification models for Central and Eastern North America (CENA). The amplification database used in model development was produced through large‐scale one‐dimensional site response analyses and overcomes limitations of prior databases by providing broader coverage of anticipated site conditions. New amplification functions conditioned on either V S30 or site natural period ( T nat ) as the primary independent variable are provided, the latter of which better captures features of the computed site amplification from the simulated database (i.e. model dispersion is reduced). Models for standard deviation also are developed. RS and FAS linear amplification functions that adjust the reference condition of V S = 3000 m/s to V S30 = 760 m/s, and account for amplification for profiles either with a sharp V S impedance or a more gradual increase in V S are also developed.
- 1 February 2024
- Published by Wiley in Earthquake Spectra
- Vol. 40 (1) , 200-229
Open AccessSimulated site amplification for Central and Eastern North America: Data set development and amplification models
This article presents a suite of response spectrum (RS) and Fourier amplitude spectrum (FAS) site amplification models for Central and Eastern North America (CENA). The amplification database used in model development was produced through large‐scale one‐dimensional site response analyses and overcomes limitations of prior databases by providing broader coverage of anticipated site conditions. New amplification functions conditioned on either V S30 or site natural period ( T nat ) as the primary independent variable are provided, the latter of which better captures features of the computed site amplification from the simulated database (i.e. model dispersion is reduced). Models for standard deviation also are developed. RS and FAS linear amplification functions that adjust the reference condition of V S = 3000 m/s to V S30 = 760 m/s, and account for amplification for profiles either with a sharp V S impedance or a more gradual increase in V S are also developed.