Alex Sangiorgi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Alex Sangiorgi has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
- Alessandra Sanson
ISTEC-CNR
8 shared publications - Nicola Sangiorgi
Institute of Science Technology and Sustainability For Ceramics National Research Council of Italy (ISSMC‐CNR) Faenza Italy
8 shared publications A. Sanson
4 shared publications- Elisa Mercadelli
Institute of Science and Technology for Ceramics, National Council of Research (ISTEC-CNR), Faenza, Italy
4 shared publications - Riccardo Bendoni
Institute of Science and Technology of Ceramic Materials (CNR‐ISTEC) Via Granarolo 64 48018 Faenza Italy
4 shared publications Alessandra Sanson
3 shared publications
Latest Publications
- Open Access
- 19 June 2026
- Published by Springer Nature in Journal of Materials Research
- Vol. 41 (12) , 1765-1784
Oxidation behavior of (Zr, Ti, Me)B2 ternary solid solutions: Effect of Me = Hf, V, Nb, Cr
- 19 June 2026
- Published by Springer Nature in Journal of Materials Research
- Vol. 41 (12) , 1765-1784
Open AccessOxidation behavior of (Zr, Ti, Me)B2 ternary solid solutions: Effect of Me = Hf, V, Nb, Cr
- Open Access
- 17 March 2026
- Published by Elsevier in Journal of Energy Chemistry
- Vol. 117, 880-892
Above 10% efficiency flexible inkjet-printed kesterite solar cells
- 17 March 2026
- Published by Elsevier in Journal of Energy Chemistry
- Vol. 117, 880-892
Open AccessAbove 10% efficiency flexible inkjet-printed kesterite solar cells
- Open Access
- 12 March 2024
- Published by Elsevier in Composites Part B: Engineering
- Vol. 277
Viable route to the manufacture of short carbon fiber-rich UHTC complex shapes with enhanced toughness
- 12 March 2024
- Published by Elsevier in Composites Part B: Engineering
- Vol. 277
Open AccessViable route to the manufacture of short carbon fiber-rich UHTC complex shapes with enhanced toughness
- Open Access
- 2 February 2024
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 267
Structural, optical, and photo-electrochemical properties of Aurivillius-type layered Bi4Ti3O12–BiFeO3 oxides
- 2 February 2024
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 267
Open AccessStructural, optical, and photo-electrochemical properties of Aurivillius-type layered Bi4Ti3O12–BiFeO3 oxides
- Open Access
An Investigation on Gel-State Electrolytes for Solar Cells Sensitized with β-Substituted Porphyrinic Dyes
The presence of a liquid electrolyte in dye-sensitized solar cells (DSSCs) is known to limit the time stability of these devices due to leakage and evaporation phenomena. To overcome this issue, gel-state electrolytes may represent a good solution in order to maintain stability and good performances, albeit at lower costs. In the present work, two different kinds of gel-electrolytes, based on poly (methyl methacrylate) (PMMA) and nanoclay agents, were investigated in DSSC-devices sensitized using β-substituted Zn-porphyrins (namely ZnPC4 and ZnPC12) with enveloping alkoxy chains of different lengths, able to produce a coverage of the photoanode surface. The highest power conversion efficiency (PCE) values equal to 1.06 ± 0.04% and 1.55 ± 0.26% were obtained for ZnPC12 (with longer alkoxy chains) with PMMA- and nanoclay-based electrolytes respectively. The properties of the photoanode/electrolyte interface as well as the influence of the gelling agents on the final properties of the obtained devices were thoroughly characterized.
Open AccessAn Investigation on Gel-State Electrolytes for Solar Cells Sensitized with β-Substituted Porphyrinic Dyes
The presence of a liquid electrolyte in dye-sensitized solar cells (DSSCs) is known to limit the time stability of these devices due to leakage and evaporation phenomena. To overcome this issue, gel-state electrolytes may represent a good solution in order to maintain stability and good performances, albeit at lower costs. In the present work, two different kinds of gel-electrolytes, based on poly (methyl methacrylate) (PMMA) and nanoclay agents, were investigated in DSSC-devices sensitized using β-substituted Zn-porphyrins (namely ZnPC4 and ZnPC12) with enveloping alkoxy chains of different lengths, able to produce a coverage of the photoanode surface. The highest power conversion efficiency (PCE) values equal to 1.06 ± 0.04% and 1.55 ± 0.26% were obtained for ZnPC12 (with longer alkoxy chains) with PMMA- and nanoclay-based electrolytes respectively. The properties of the photoanode/electrolyte interface as well as the influence of the gelling agents on the final properties of the obtained devices were thoroughly characterized.
- Open Access
Additive-Free Gelatine-Based Devices for Chondral Tissue Regeneration: Shaping Process Comparison among Mould Casting and Three-Dimensional Printing
Gelatine is a well-known and extensively studied biopolymer, widely used in recent decades to create biomaterials in many different ways, exploiting its molecular resemblance with collagen, the main constituent of the extra-cellular matrix, from which it is derived. Many have employed this biopolymer in tissue engineering and chemically modified (e.g., gelatin methacryloyl) or blended it with other polymers (e.g., alginate) to modulate or increase its performances and printability. Nevertheless, little is reported about its use as a stand-alone material. Moreover, despite the fact that multiple works have been reported on the realization of mould-casted and three-dimensional printed scaffolds in tissue engineering, a clear comparison among these two shaping processes, towards a comparable workflow starting from the same material, has never been published. Herein, we report the use of gelatine as stand-alone material, not modified, blended, or admixed to be processed or crosslinked, for the realization of suitable scaffolds for tissue engineering, towards the two previously mentioned shaping processes. To make the comparison reliable, the same pre-process (e.g., the gelatin solution preparation) and post-process (e.g., freeze-drying and crosslinking) steps were applied. In this study, gelatine solution was firstly rheologically characterized to find a formulation suitable for being processed with both the shaping processes selected. The realized scaffolds were then morphologically, phisico-chemically, mechanically, and biologically characterized to determine and compare their performances. Despite the fact that the same starting material was employed, as well as the same pre- and post-process steps, the two groups resulted, for most aspects, in diametrically opposed characteristics. The mould-casted scaffolds that resulted were characterized by small, little-interconnected, and random porosity, high resistance to compression and slow cell colonization, while the three-dimensional printed scaffolds displayed big, well-interconnected, and geometrically defined porosity, high elasticity and recover ability after compression, as well as fast and deep cell colonization.
Open AccessAdditive-Free Gelatine-Based Devices for Chondral Tissue Regeneration: Shaping Process Comparison among Mould Casting and Three-Dimensional Printing
Gelatine is a well-known and extensively studied biopolymer, widely used in recent decades to create biomaterials in many different ways, exploiting its molecular resemblance with collagen, the main constituent of the extra-cellular matrix, from which it is derived. Many have employed this biopolymer in tissue engineering and chemically modified (e.g., gelatin methacryloyl) or blended it with other polymers (e.g., alginate) to modulate or increase its performances and printability. Nevertheless, little is reported about its use as a stand-alone material. Moreover, despite the fact that multiple works have been reported on the realization of mould-casted and three-dimensional printed scaffolds in tissue engineering, a clear comparison among these two shaping processes, towards a comparable workflow starting from the same material, has never been published. Herein, we report the use of gelatine as stand-alone material, not modified, blended, or admixed to be processed or crosslinked, for the realization of suitable scaffolds for tissue engineering, towards the two previously mentioned shaping processes. To make the comparison reliable, the same pre-process (e.g., the gelatin solution preparation) and post-process (e.g., freeze-drying and crosslinking) steps were applied. In this study, gelatine solution was firstly rheologically characterized to find a formulation suitable for being processed with both the shaping processes selected. The realized scaffolds were then morphologically, phisico-chemically, mechanically, and biologically characterized to determine and compare their performances. Despite the fact that the same starting material was employed, as well as the same pre- and post-process steps, the two groups resulted, for most aspects, in diametrically opposed characteristics. The mould-casted scaffolds that resulted were characterized by small, little-interconnected, and random porosity, high resistance to compression and slow cell colonization, while the three-dimensional printed scaffolds displayed big, well-interconnected, and geometrically defined porosity, high elasticity and recover ability after compression, as well as fast and deep cell colonization.
- Open Access
Photoelectrochemical Hydrogen Production by Screen-Printed Copper Oxide Electrodes
In this work, copper oxides-based photocathodes for photoelectrochemical cells (PEC) were produced for the first time by screen printing. A total 7 × 10−3 g/m2 glycerine trioleate was found as optimum deflocculant amount to assure stable and homogeneous inks, based on CuO nano-powder. The inks were formulated considering different binder amounts and deposited producing films with homogenous thickness, microstructure, and roughness. The as-produced films were thermally treated to obtain Cu2O- and Cu2O/CuO-based electrodes. The increased porosity obtained by adding higher amounts of binder in the ink positively affected the electron transfer from the surface of the electrode to the electrolyte, thus increasing the corresponding photocurrent values. Moreover, the Cu2O/CuO system showed a higher charge carrier and photocurrent density than the Cu2O-based one. The mixed Cu2O/CuO films allowed the most significant hydrogen production, especially in slightly acid reaction conditions.
Open AccessPhotoelectrochemical Hydrogen Production by Screen-Printed Copper Oxide Electrodes
In this work, copper oxides-based photocathodes for photoelectrochemical cells (PEC) were produced for the first time by screen printing. A total 7 × 10−3 g/m2 glycerine trioleate was found as optimum deflocculant amount to assure stable and homogeneous inks, based on CuO nano-powder. The inks were formulated considering different binder amounts and deposited producing films with homogenous thickness, microstructure, and roughness. The as-produced films were thermally treated to obtain Cu2O- and Cu2O/CuO-based electrodes. The increased porosity obtained by adding higher amounts of binder in the ink positively affected the electron transfer from the surface of the electrode to the electrolyte, thus increasing the corresponding photocurrent values. Moreover, the Cu2O/CuO system showed a higher charge carrier and photocurrent density than the Cu2O-based one. The mixed Cu2O/CuO films allowed the most significant hydrogen production, especially in slightly acid reaction conditions.
- 1 January 2020
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 204
Improving the efficiency of thin-film fiber-shaped dye-sensitized solar cells by using organic sensitizers
- 1 January 2020
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 204
Improving the efficiency of thin-film fiber-shaped dye-sensitized solar cells by using organic sensitizers
- 1 August 2019
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 39 (9) , 2908-2914
Semiconductor water-based inks: Miniaturized NiO pseudocapacitor electrodes by inkjet printing
- 1 August 2019
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 39 (9) , 2908-2914
Semiconductor water-based inks: Miniaturized NiO pseudocapacitor electrodes by inkjet printing
- 1 May 2019
- Published by Elsevier in Electrochimica Acta
- Vol. 305, 322-328
Molecularly imprinted polypyrrole counter electrode for gel-state dye-sensitized solar cells
- 1 May 2019
- Published by Elsevier in Electrochimica Acta
- Vol. 305, 322-328
Molecularly imprinted polypyrrole counter electrode for gel-state dye-sensitized solar cells