Tiziana Fischetti
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tiziana Fischetti has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Gabriela Graziani
Human Sciences and Life Quality Promotion Department, San Raffaele Rome University, via di val cannuta 247, Rome, Italy
2 shared publications - Nicola Baldini
Department of Biomedical and Neuromotor Sciences, University of Bologna, Bologna, Italy
2 shared publications - Daniele Ghezzi
Department of Pharmacy and Biotechnology (FaBiT), University of Bologna, Bologna, Italy
1 shared publication - Friederike Kaiser
Department for Functional Materials in Medicine and Dentistry, University of Würzburg, Pleicherwall 2, D-97070 Würzburg, Germany
1 shared publication - Gemma Di Pompo
Biomedical Science, Technologies, and Nanobiotechnology Lab, IRCCS Istituto Ortopedico Rizzoli, Bologna, Italy
1 shared publication - Giorgia Borciani
RAMSES Laboratory, Research Centre Codivilla‐Putti, IRCCS Istituto Ortopedico Rizzoli Bologna Italy
1 shared publication
Latest Publications
- Open Access
- 13 February 2024
- Published by IOP Publishing in Biomedical Materials
- Vol. 19 (2) , 025033
Advantages and limitations of using cell viability assays for 3D bioprinted constructs
Bioprinting shows promise for bioengineered scaffolds and three-dimensional (3D) disease models, but assessing the viability of embedded cells is challenging. Conventional assays are limited by the technical problems that derive from using multi-layered bioink matrices dispersing cells in three dimensions. In this study, we tested bioprinted osteogenic bioinks as a model system. Alginate- or gelatin-based bioinks were loaded with/without ceramic microparticles and osteogenic cells (bone tumor cells, with or without normal bone cells). Despite demonstrating 80%–90% viability through manual counting and live/dead staining, this was time-consuming and operator-dependent. Moreover, for the alginate-bioprinted scaffold, cell spheroids could not be distinguished from single cells. The indirect assay (alamarBlue), was faster but less accurate than live/dead staining due to dependence on hydrogel permeability. Automated confocal microscope acquisition and cell counting of live/dead staining was more reproducible, reliable, faster, efficient, and avoided overestimates compared to manual cell counting by optical microscopy. Finally, for 1.2 mm thick 3D bioprints, dual-photon confocal scanning with vital staining greatly improved the precision of the evaluation of cell distribution and viability and cell–cell interactions through the z-axis. In summary, automated confocal microscopy and cell counting provided superior accuracy for the assessment of cell viability and interactions in 3D bioprinted models compared to most commonly and currently used techniques.
- 13 February 2024
- Published by IOP Publishing in Biomedical Materials
- Vol. 19 (2) , 025033
Open AccessAdvantages and limitations of using cell viability assays for 3D bioprinted constructs
Bioprinting shows promise for bioengineered scaffolds and three-dimensional (3D) disease models, but assessing the viability of embedded cells is challenging. Conventional assays are limited by the technical problems that derive from using multi-layered bioink matrices dispersing cells in three dimensions. In this study, we tested bioprinted osteogenic bioinks as a model system. Alginate- or gelatin-based bioinks were loaded with/without ceramic microparticles and osteogenic cells (bone tumor cells, with or without normal bone cells). Despite demonstrating 80%–90% viability through manual counting and live/dead staining, this was time-consuming and operator-dependent. Moreover, for the alginate-bioprinted scaffold, cell spheroids could not be distinguished from single cells. The indirect assay (alamarBlue), was faster but less accurate than live/dead staining due to dependence on hydrogel permeability. Automated confocal microscope acquisition and cell counting of live/dead staining was more reproducible, reliable, faster, efficient, and avoided overestimates compared to manual cell counting by optical microscopy. Finally, for 1.2 mm thick 3D bioprints, dual-photon confocal scanning with vital staining greatly improved the precision of the evaluation of cell distribution and viability and cell–cell interactions through the z-axis. In summary, automated confocal microscopy and cell counting provided superior accuracy for the assessment of cell viability and interactions in 3D bioprinted models compared to most commonly and currently used techniques.
- Open Access
- 8 January 2024
- Published by Wiley in Advanced Materials Technologies
- Vol. 9 (5)
Combining 3D Printing and Cryostructuring to Tackle Infection and Spine Fusion
Low back pain is among the main issues in vertebral orthopaedics. Intervertebral disk degeneration can be severe, up to requiring the replacement of the damaged disk by substitutes to achieve spine fusion. Disk removal results in critical size defects, so fusion does not occur naturally, but synthetic bone grafts are needed. Since the surgical procedure is time‐consuming, high infection rates occur. Hence, in spine fusion, bone regeneration enhancement and infection prevention are needed. Here, a new dual‐component system is proposed, to tackle both issues at one time. To enable spine fusion, 3D extrusion‐based printing is employed to develop coherent custom magnesium phosphate (CaMgP)‐based cages. The 3D‐printed scaffolds are hardened, and the structural properties are evaluated to be within the ranges of physiological bone. To prevent infection, an in‐house ice‐templating device is employed in combination with a 3D‐printed ceramic scaffold, to develop tailored porous alginate structures loaded with vancomycin. Results show that CaMgP can be printed into complex geometries and that the geometry influences the pore orientation during ice‐templating. These structures loaded with vancomycin have antibacterial properties against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) strains.
- 8 January 2024
- Published by Wiley in Advanced Materials Technologies
- Vol. 9 (5)
Open AccessCombining 3D Printing and Cryostructuring to Tackle Infection and Spine Fusion
Low back pain is among the main issues in vertebral orthopaedics. Intervertebral disk degeneration can be severe, up to requiring the replacement of the damaged disk by substitutes to achieve spine fusion. Disk removal results in critical size defects, so fusion does not occur naturally, but synthetic bone grafts are needed. Since the surgical procedure is time‐consuming, high infection rates occur. Hence, in spine fusion, bone regeneration enhancement and infection prevention are needed. Here, a new dual‐component system is proposed, to tackle both issues at one time. To enable spine fusion, 3D extrusion‐based printing is employed to develop coherent custom magnesium phosphate (CaMgP)‐based cages. The 3D‐printed scaffolds are hardened, and the structural properties are evaluated to be within the ranges of physiological bone. To prevent infection, an in‐house ice‐templating device is employed in combination with a 3D‐printed ceramic scaffold, to develop tailored porous alginate structures loaded with vancomycin. Results show that CaMgP can be printed into complex geometries and that the geometry influences the pore orientation during ice‐templating. These structures loaded with vancomycin have antibacterial properties against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) strains.