Phillip C. Chesser
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Phillip C. Chesser has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Brian Post
Manufacturing Science Division, Oak Ridge National Laboratory, Knoxville, TN 37932, USA
2 shared publications - Jesse Heineman
Manufacturing Science Division, Oak Ridge National Laboratory, Knoxville, TN 37932, USA
2 shared publications - Peter Wang
ORNL
2 shared publications - Aaron Wysocki
Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)
1 shared publication - Alex Boulger1 shared publication
- Alex Roschli
ORNL
1 shared publication
Latest Publications
- 23 September 2021
- Published by ASME International in Journal of Mechanisms and Robotics
- Vol. 14 (2) , 1-17
Kinematics of a Cable-Driven Robotic Platform for Large-Scale Additive Manufacturing
Concrete additive manufacturing (AM) is a growing field of research. However, on-site, large-scale concrete additive manufacturing requires motion platforms that are difficult to implement with conventional rigid-link robotic systems. This article presents a new kinematic arrangement for a deployable cable-driven robot intended for on-site AM. The kinematics of this robot are examined to determine if they meet the requirements for this application, the wrench feasible workspace (WFW) is examined, and the physical implementation of a prototype is also presented. Data collected from the physical implementation of the proposed system are analyzed, and the results support its suitability for the intended application. The success of this system demonstrates that this kinematic arrangement is promising for future deployable AM systems.
- 23 September 2021
- Published by ASME International in Journal of Mechanisms and Robotics
- Vol. 14 (2) , 1-17
Kinematics of a Cable-Driven Robotic Platform for Large-Scale Additive Manufacturing
Concrete additive manufacturing (AM) is a growing field of research. However, on-site, large-scale concrete additive manufacturing requires motion platforms that are difficult to implement with conventional rigid-link robotic systems. This article presents a new kinematic arrangement for a deployable cable-driven robot intended for on-site AM. The kinematics of this robot are examined to determine if they meet the requirements for this application, the wrench feasible workspace (WFW) is examined, and the physical implementation of a prototype is also presented. Data collected from the physical implementation of the proposed system are analyzed, and the results support its suitability for the intended application. The success of this system demonstrates that this kinematic arrangement is promising for future deployable AM systems.
- Open Access
- 16 July 2021
- Published by ASME International
Construction-Scale Concrete Additive Manufacturing and its Application in Infrastructure Energy Storage
Conventional construction is a labor intensive, hazardous, expensive, inefficient, and wasteful process. According to the EPA, 534 million tons of construction debris were generated in the United States in 2014, which is more than twice the amount of generated municipal solid waste. In addition, conventional construction materials are often used inefficiently and with poor quality
- 16 July 2021
- Published by ASME International
Open AccessConstruction-Scale Concrete Additive Manufacturing and its Application in Infrastructure Energy Storage
Conventional construction is a labor intensive, hazardous, expensive, inefficient, and wasteful process. According to the EPA, 534 million tons of construction debris were generated in the United States in 2014, which is more than twice the amount of generated municipal solid waste. In addition, conventional construction materials are often used inefficiently and with poor quality
- Open Access
- 19 March 2021
- Published by MDPI AG in Journal of Nuclear Engineering
- Vol. 2 (1) , 74-85
Candidate Core Designs for the Transformational Challenge Reactor
Early cycle activities under the Transformational Challenge Reactor (TCR) program focused on analyzing and maturing four reactor core design concepts: two fast-spectrum systems and two thermal-spectrum systems. A rapid, iterative approach has been implemented through which designs can be modified and analyzed and subcomponents can be manufactured in parallel over time frames of weeks rather than months or years. To meet key program initiatives (e.g., timeline, material use), several constraints—including fissile material availability (less than 250 kg of HALEU), component availabilities, materials compatibility, and additive manufacturing capabilities—were factored into the design effort, yielding small (less than one cubic meter in volume) cores with near-term viability. The fast-spectrum designs did not meet the fissile material constraint, so the thermal-spectrum systems became the primary design focus. Since significant progress has been made on advanced moderator materials (YHx) under the TCR program, gas-cooled thermal-spectrum systems using less than 250 kg of HALEU that occupy less than 1 m3 are now feasible. The designs for two of these systems have been evolved and matured. In both thermal-spectrum design concepts, bidirectional coolant flow is used. Coolant flows down through YHx moderator elements and is reversed in a bottom manifold and core support structure, and then flows up though or around the fuel elements. The main difference between the two thermal-spectrum design concepts is the fuel elements—one uses traditional UO2 ceramic fuel, and the other uses UN-bearing TRISO fuel particles embedded inside a SiC matrix. Core neutronics and thermal performance for these systems are assessed and summarized herein.
- 19 March 2021
- Published by MDPI AG in Journal of Nuclear Engineering
- Vol. 2 (1) , 74-85
Open AccessCandidate Core Designs for the Transformational Challenge Reactor
Early cycle activities under the Transformational Challenge Reactor (TCR) program focused on analyzing and maturing four reactor core design concepts: two fast-spectrum systems and two thermal-spectrum systems. A rapid, iterative approach has been implemented through which designs can be modified and analyzed and subcomponents can be manufactured in parallel over time frames of weeks rather than months or years. To meet key program initiatives (e.g., timeline, material use), several constraints—including fissile material availability (less than 250 kg of HALEU), component availabilities, materials compatibility, and additive manufacturing capabilities—were factored into the design effort, yielding small (less than one cubic meter in volume) cores with near-term viability. The fast-spectrum designs did not meet the fissile material constraint, so the thermal-spectrum systems became the primary design focus. Since significant progress has been made on advanced moderator materials (YHx) under the TCR program, gas-cooled thermal-spectrum systems using less than 250 kg of HALEU that occupy less than 1 m3 are now feasible. The designs for two of these systems have been evolved and matured. In both thermal-spectrum design concepts, bidirectional coolant flow is used. Coolant flows down through YHx moderator elements and is reversed in a bottom manifold and core support structure, and then flows up though or around the fuel elements. The main difference between the two thermal-spectrum design concepts is the fuel elements—one uses traditional UO2 ceramic fuel, and the other uses UN-bearing TRISO fuel particles embedded inside a SiC matrix. Core neutronics and thermal performance for these systems are assessed and summarized herein.