Jae-Hyuk Park
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jae-Hyuk Park has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
Byung Joo Jeong
School of Advanced Science Materials and Engineering, Sungkyunkwan University, Suwon 16419, Republic of Korea
2 shared publications- Hak Ki Yu
Department of Materials Science and Engineering & Department of Energy Systems Research, Ajou University, Suwon 16499, Republic of Korea
2 shared publications - Jae-Young Choi
School of Advanced Materials Science and Engineering, Sungkyunkwan University, Suwon 16419, Republic of Korea
2 shared publications Jiho Jeon
SKKU Advanced Institute of Nanotechnology (SAINT), Sungkyunkwan University, Suwon 16419, Republic of Korea
2 shared publicationsJinsu Kang
School of Advanced Science Materials and Engineering, Sungkyunkwan University, Suwon 16419, Republic of Korea
2 shared publicationsKyung Hwan Choi
SKKU Advanced Institute of Nanotechnology (SAINT), Sungkyunkwan University, Suwon 16419, Republic of Korea
2 shared publications
Latest Publications
- Open Access
- 22 November 2025
- Published by Elsevier in Materials & Design
- Vol. 260
An entangled material made from fiber aerosol deposition method
- 22 November 2025
- Published by Elsevier in Materials & Design
- Vol. 260
Open AccessAn entangled material made from fiber aerosol deposition method
- Open Access
Analysis of Grain Growth Behavior of Intermetallic Compounds on Plated Pure Sn for Micropump Solder Caps
We evaluated for the morphology and growth behavior of IMC grain according to number of reflows of solder cap pure Sn microbumps. In the structure of Ni barrier/Cu layer between Cu pillar and pure Sn, solder cap pure Sn on the top layer was analyzed for the behavior change of IMC grain according to the number of reflows. The height and diameter of the bumps on the wafer were designed to be 40 μm and 30 μm, respectively. The vertical structure of the microbump consisted of Ti/Cu (1000 Å/2000 Å), Cu pillar (20 µm), Ni barrier (3 µm), and Cu (1 µm). The overall height of the bump is about 40 μm. Additionally, the height of the solder cap pure Sn as the last layer is 20 μm. The diameter of the bump is 30 μm. It was formed using plating. After plating to solder cap Sn, it was finally formed for the microbump using reflow. Samples were prepared according to the number of reflows (1, 3, 5, 7, and 9). To observe the grain morphology of the IMC, the pure Sn on the upper layer (solder cap) was removed using SupraBond RO-22 etchant. In the removed state, the morphology of the IMC grain was evaluated to the inside surface of bump using SEM and a 3D scope. The average number of IMC grains decreased linearly during reflow cycles 1 to 5 and then gradually decreased during reflow cycles 7 to 10. The average surface area of IMC grains was 18.243 μm when reflow was performed once. The average surface area of IMC grains increased proportionally for reflow cycles 1 to 10. Based on the experimental results, when the count of reflow was performed more than 10 times, it was confirmed that the solder cap pure Sn was reduced by more than 50% due to the increase in the area of IMC grain.
Open AccessAnalysis of Grain Growth Behavior of Intermetallic Compounds on Plated Pure Sn for Micropump Solder Caps
We evaluated for the morphology and growth behavior of IMC grain according to number of reflows of solder cap pure Sn microbumps. In the structure of Ni barrier/Cu layer between Cu pillar and pure Sn, solder cap pure Sn on the top layer was analyzed for the behavior change of IMC grain according to the number of reflows. The height and diameter of the bumps on the wafer were designed to be 40 μm and 30 μm, respectively. The vertical structure of the microbump consisted of Ti/Cu (1000 Å/2000 Å), Cu pillar (20 µm), Ni barrier (3 µm), and Cu (1 µm). The overall height of the bump is about 40 μm. Additionally, the height of the solder cap pure Sn as the last layer is 20 μm. The diameter of the bump is 30 μm. It was formed using plating. After plating to solder cap Sn, it was finally formed for the microbump using reflow. Samples were prepared according to the number of reflows (1, 3, 5, 7, and 9). To observe the grain morphology of the IMC, the pure Sn on the upper layer (solder cap) was removed using SupraBond RO-22 etchant. In the removed state, the morphology of the IMC grain was evaluated to the inside surface of bump using SEM and a 3D scope. The average number of IMC grains decreased linearly during reflow cycles 1 to 5 and then gradually decreased during reflow cycles 7 to 10. The average surface area of IMC grains was 18.243 μm when reflow was performed once. The average surface area of IMC grains increased proportionally for reflow cycles 1 to 10. Based on the experimental results, when the count of reflow was performed more than 10 times, it was confirmed that the solder cap pure Sn was reduced by more than 50% due to the increase in the area of IMC grain.
- 3 December 2024
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 27 (3) , 366-371
Chemical vapor transport synthesis of one-dimensional V 2 PS 10 and its application in miniaturized UV sensors
We demonstrate the synthesis of high-quality one-dimensional V 2 PS 10 crystals and their successful application as UV sensors, highlighting their potential for miniaturized electronic devices.
- 3 December 2024
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 27 (3) , 366-371
Chemical vapor transport synthesis of one-dimensional V 2 PS 10 and its application in miniaturized UV sensors
We demonstrate the synthesis of high-quality one-dimensional V 2 PS 10 crystals and their successful application as UV sensors, highlighting their potential for miniaturized electronic devices.
- 29 December 2023
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 26 (6) , 817-821
Chalcogen alloying for band structure modulation of antimony chalcogen iodide alloy: 1D van der Waals materials SbSI–SbSeI system
Alloys of SbSI and SbSeI, 1D van der Waals materials, were synthesized through chalcogen atom substitution. The band structure and photocurrent were modulated based on the composition of the synthesized alloy.
- 29 December 2023
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 26 (6) , 817-821
Chalcogen alloying for band structure modulation of antimony chalcogen iodide alloy: 1D van der Waals materials SbSI–SbSeI system
Alloys of SbSI and SbSeI, 1D van der Waals materials, were synthesized through chalcogen atom substitution. The band structure and photocurrent were modulated based on the composition of the synthesized alloy.