Kyung-Jae Shin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kyung-Jae Shin has a total of 54 co-authors. Here are the top co-authors by number of shared publications:
- Hee-Du Lee
Regional Center for Land, Infrastructure and Transport Technology, Kyungpook National University, Daegu 41566, Republic of Korea
13 shared publications Swoo-Heon Lee
12 shared publications- Jun-Seop Lee
Kyungpook National University, Daegu, Korea
11 shared publications Hee-Du Lee
7 shared publications- Swoo-Heon Lee
School of Convergence & Fusion System Engineering, Kyungpook National University, Daegu 41566, Republic of Korea
6 shared publications Jun-Seop Lee
4 shared publications
Latest Publications
- Open Access
Experimental and Analytical Study on Non-Damaged Reinforcement Method for Pipe Rack Steel Structures
Pipe racks are steel structures that support various pipes transporting materials in industrial complexes. The pipes on pipe racks may transport hazardous substances, which imposes limitations on their structural reinforcement. Therefore, this study aimed to propose methods for reinforcing the joints of pipe rack structures through non-welding and non-drilling techniques. The joints of pipe rack structures were connected by end plates. Initially, this study evaluated the capacity of existing end plates in a real-world experiment and conducted cyclic loading tests with two additional reinforcement methods to validate their performance. Finally, finite element analysis was conducted to explore additional variables that were not covered in the experiments, and the optimal reinforcement method that demonstrated the best performance was proposed.
Open AccessExperimental and Analytical Study on Non-Damaged Reinforcement Method for Pipe Rack Steel Structures
Pipe racks are steel structures that support various pipes transporting materials in industrial complexes. The pipes on pipe racks may transport hazardous substances, which imposes limitations on their structural reinforcement. Therefore, this study aimed to propose methods for reinforcing the joints of pipe rack structures through non-welding and non-drilling techniques. The joints of pipe rack structures were connected by end plates. Initially, this study evaluated the capacity of existing end plates in a real-world experiment and conducted cyclic loading tests with two additional reinforcement methods to validate their performance. Finally, finite element analysis was conducted to explore additional variables that were not covered in the experiments, and the optimal reinforcement method that demonstrated the best performance was proposed.
- 10 June 2024
- Published by Springer Nature in International Journal of Steel Structures
- Vol. 24 (6) , 1290-1303
Strength Evaluation of Flush End-Plate Connection Using Triangular Haunch in Pipe Rack
- 10 June 2024
- Published by Springer Nature in International Journal of Steel Structures
- Vol. 24 (6) , 1290-1303
Strength Evaluation of Flush End-Plate Connection Using Triangular Haunch in Pipe Rack
- Open Access
- 6 September 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (18) , 10033
Experiments and Design of an Anti-Disaster Support System for Apple Orchards
A number of apple trees have collapsed in South Korea due to strong winds caused by typhoons. In fact, apple trees are protected by various types of support systems. However, despite this, they have still been damaged. The reason why the trees collapsed is that the installation of a support system is based not on scientific facts but on empirical facts. The purpose of this study was to evaluate the structural safety of the anti-disaster support system of apple trees. Equivalent static tests of the support systems, i.e., fences and matrix supports, were carried out. The result of the equivalent static tests indicated that the bearing capacity of the foundation is considered an important factor for the performance of the fence support, and the elements played a major role in the case of the matrix support due to the connection of the strut wire and the mat wire. Based on this test result, design criteria and standard specifications of the apple tree support system in response to local wind speed are proposed.
- 6 September 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (18) , 10033
Open AccessExperiments and Design of an Anti-Disaster Support System for Apple Orchards
A number of apple trees have collapsed in South Korea due to strong winds caused by typhoons. In fact, apple trees are protected by various types of support systems. However, despite this, they have still been damaged. The reason why the trees collapsed is that the installation of a support system is based not on scientific facts but on empirical facts. The purpose of this study was to evaluate the structural safety of the anti-disaster support system of apple trees. Equivalent static tests of the support systems, i.e., fences and matrix supports, were carried out. The result of the equivalent static tests indicated that the bearing capacity of the foundation is considered an important factor for the performance of the fence support, and the elements played a major role in the case of the matrix support due to the connection of the strut wire and the mat wire. Based on this test result, design criteria and standard specifications of the apple tree support system in response to local wind speed are proposed.
- Open Access
Design Methodology of U-Shaped Infilled Composite Beams with Angled Shear Connectors Using Finite Element Analysis
A composite beam is a structural member that behaves as a single unit by using shear connectors between a concrete slab and an I-shaped steel girder. The composite ratio is crucial and is determined by the shear connectors’ ability to withstand the horizontal shear forces between the concrete and steel girder. In this study, a U-shaped composite beam was designed, which differs from conventional composite beams as it allows the use of a steel girder as a formwork. Moreover, angle-type shear connectors, instead of stud-type connectors, were employed. Based on this design, large-scale U-shaped composite beams with angle-type shear connectors were fabricated, and load tests were conducted to analyze the behavior after composite action and the influence of shear connector spacing. Additionally, the strength of the angle-type shear connectors used in this paper was evaluated through finite element analysis. Finally, a strength evaluation method for composite beams of this configuration is proposed.
Open AccessDesign Methodology of U-Shaped Infilled Composite Beams with Angled Shear Connectors Using Finite Element Analysis
A composite beam is a structural member that behaves as a single unit by using shear connectors between a concrete slab and an I-shaped steel girder. The composite ratio is crucial and is determined by the shear connectors’ ability to withstand the horizontal shear forces between the concrete and steel girder. In this study, a U-shaped composite beam was designed, which differs from conventional composite beams as it allows the use of a steel girder as a formwork. Moreover, angle-type shear connectors, instead of stud-type connectors, were employed. Based on this design, large-scale U-shaped composite beams with angle-type shear connectors were fabricated, and load tests were conducted to analyze the behavior after composite action and the influence of shear connector spacing. Additionally, the strength of the angle-type shear connectors used in this paper was evaluated through finite element analysis. Finally, a strength evaluation method for composite beams of this configuration is proposed.
- Open Access
- 25 July 2023
- Published by MDPI AG in Preprints.org
FEA of Infilled Composite Beam Using Angle Type Shear Connector
A composite beam is a structural member that behaves as a single unit by using shear connectors between a concrete slab and an H-shaped steel girder. The composite ratio is crucial and determined by the shear connectors' ability to withstand the horizontal shear forces between the concrete and steel girder. In this study, a U-shaped composite beam was designed, which differs from conventional composite beams as it allows the use of a steel girder as a formwork. Moreover, angle-type shear connectors, instead of stud-type connectors, were employed. Based on this design, large-scale U-shaped composite beams with angle-type shear connectors were fabricated, and load tests were conducted to analyze the behavior after composite action and the influence of shear connector spacing. Additionally, the strength of the angle-type shear connectors used in this paper was evaluated through finite element analysis. Finally, a strength evaluation method for composite beams of this configuration was proposed.
- 25 July 2023
- Published by MDPI AG in Preprints.org
Open AccessFEA of Infilled Composite Beam Using Angle Type Shear Connector
A composite beam is a structural member that behaves as a single unit by using shear connectors between a concrete slab and an H-shaped steel girder. The composite ratio is crucial and determined by the shear connectors' ability to withstand the horizontal shear forces between the concrete and steel girder. In this study, a U-shaped composite beam was designed, which differs from conventional composite beams as it allows the use of a steel girder as a formwork. Moreover, angle-type shear connectors, instead of stud-type connectors, were employed. Based on this design, large-scale U-shaped composite beams with angle-type shear connectors were fabricated, and load tests were conducted to analyze the behavior after composite action and the influence of shear connector spacing. Additionally, the strength of the angle-type shear connectors used in this paper was evaluated through finite element analysis. Finally, a strength evaluation method for composite beams of this configuration was proposed.
- 27 March 2023
- Published by Springer Nature in International Journal of Steel Structures
- Vol. 23 (3) , 795-805
Strength Evaluation of End-Plate Connections Using Stiffness Reduction Factor
- 27 March 2023
- Published by Springer Nature in International Journal of Steel Structures
- Vol. 23 (3) , 795-805
Strength Evaluation of End-Plate Connections Using Stiffness Reduction Factor
- 28 October 2022
- Published by Springer Nature in International Journal of Steel Structures
- Vol. 22 (6) , 1908-1917
The Measurement of Construction Error Technology for Deformable Modular System by Image Processing
- 28 October 2022
- Published by Springer Nature in International Journal of Steel Structures
- Vol. 22 (6) , 1908-1917
The Measurement of Construction Error Technology for Deformable Modular System by Image Processing
- 27 January 2022
- Published by Korean Society of Steel Construction in Journal of Korean Society of Steel Construction
- Vol. 34 (1) , 45-53
Structural Performance Evaluation of Modular System Connections Using Special Blocks
- 27 January 2022
- Published by Korean Society of Steel Construction in Journal of Korean Society of Steel Construction
- Vol. 34 (1) , 45-53
Structural Performance Evaluation of Modular System Connections Using Special Blocks
- 27 August 2021
- Published by Korean Society of Steel Construction in Journal of Korean Society of Steel Construction
- Vol. 33 (4) , 237-245
Strength Evaluation and Finite Element Analysis of Channel Shear Connectors
- 27 August 2021
- Published by Korean Society of Steel Construction in Journal of Korean Society of Steel Construction
- Vol. 33 (4) , 237-245
Strength Evaluation and Finite Element Analysis of Channel Shear Connectors
- 27 June 2021
- Published by Korean Society of Steel Construction in Journal of Korean Society of Steel Construction
- Vol. 33 (3) , 153-161
Evaluation of Structural Performance of Beam with Embossed Webs According to Web Length
- 27 June 2021
- Published by Korean Society of Steel Construction in Journal of Korean Society of Steel Construction
- Vol. 33 (3) , 153-161
Evaluation of Structural Performance of Beam with Embossed Webs According to Web Length