Lucas Hoof
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lucas Hoof has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Kai Junge Puring
Fraunhofer‐Institut für Umwelt‐, Sicherheits‐ und Energietechnik UMSICHT Power‐to‐Chemicals Osterfelder Str. 3 46047 Oberhausen Germany
2 shared publications - Kevinjeorjios Pellumbi
Fraunhofer Institute for Environmental, Safety and Energy Technology, UMSICHT, Oberhausen, Germany
2 shared publications - Ulf-Peter Apfel
Ruhr‐Universität Bochum Fakultät Für Chemie und Biochemie Anorganische Chemie I Bochum Germany
2 shared publications Anna Grevé
Fraunhofer Institute for Environmental Safety and Energy Technology UMSICHT 46047 Oberhausen Germany
1 shared publication- Corina Andronescu
Chemical Technology III, Faculty of Chemistry and CENIDE, Center for Nanointegration, University of Duisburg-Essen, Universitätsstraße 7, 45141 Essen, Germany
1 shared publication - Dennis Blaudszun
Fraunhofer Institute for Environmental Safety and Energy Technology UMSICHT Osterfelderstr. 3 46047 Oberhausen Germany
1 shared publication
Latest Publications
- Open Access
- 20 July 2024
- Published by Wiley in Advanced Energy Materials
- Vol. 14 (40)
Carbon Bipolar Plates in PEM Water Electrolysis: Bust or Must?
Reducing the cost of PEM water electrolyzers is crucial for making green hydrogen economically viable achievable by cheaper catalysts as well as bipolar plates. This study demonstrates for the first time the use of uncoated carbon bipolar plates (C‐BPs) as an alternative to titanium bipolar plates (Ti‐BPs). The corrosion phenomena of C‐BPs versus Ti‐BPs are investigated through ex situ and in situ accelerated stress tests. The findings show that pH values, especially between 1 and 0, exponentially influence the corrosion current density of bipolar plates. Ex situ tests revealed significantly higher corrosion current densities for C‐BPs compared to Ti‐BPs (e.g., 170 times higher at pH 1 and 80 °C). Yet, tests applying C‐BPs in a Proton Exchange Membrane Electrolyzer operated for at least 567 h at alternating current densities of 1 and 3 A cm⁻2 with low degradation rates (16.41 µV h⁻¹ at 1 A cm⁻2 and 31.92 µV h⁻¹ at 3 A cm⁻2), comparable to Ti‐BPs. Contrary to general perceptions, C‐BPs are stable under application‐ready conditions and do not corrode as previously expected. This study highlights the potential of C‐BPs in electrolyzers, showcasing the potential to reduce the costs of the electrolyzers.
- 20 July 2024
- Published by Wiley in Advanced Energy Materials
- Vol. 14 (40)
Open AccessCarbon Bipolar Plates in PEM Water Electrolysis: Bust or Must?
Reducing the cost of PEM water electrolyzers is crucial for making green hydrogen economically viable achievable by cheaper catalysts as well as bipolar plates. This study demonstrates for the first time the use of uncoated carbon bipolar plates (C‐BPs) as an alternative to titanium bipolar plates (Ti‐BPs). The corrosion phenomena of C‐BPs versus Ti‐BPs are investigated through ex situ and in situ accelerated stress tests. The findings show that pH values, especially between 1 and 0, exponentially influence the corrosion current density of bipolar plates. Ex situ tests revealed significantly higher corrosion current densities for C‐BPs compared to Ti‐BPs (e.g., 170 times higher at pH 1 and 80 °C). Yet, tests applying C‐BPs in a Proton Exchange Membrane Electrolyzer operated for at least 567 h at alternating current densities of 1 and 3 A cm⁻2 with low degradation rates (16.41 µV h⁻¹ at 1 A cm⁻2 and 31.92 µV h⁻¹ at 3 A cm⁻2), comparable to Ti‐BPs. Contrary to general perceptions, C‐BPs are stable under application‐ready conditions and do not corrode as previously expected. This study highlights the potential of C‐BPs in electrolyzers, showcasing the potential to reduce the costs of the electrolyzers.
- Open Access
- 26 January 2024
- Published by Wiley in ChemElectroChem
- Vol. 11 (5)
Exploring the (Dis)‐Similarities of Half‐Cell and Full Cell Zero‐Gap Electrolyzers for the CO2 Electroreduction
Carbon dioxide electroreduction (CO2R) is a promising technology for mitigating industrial CO2 emissions and generating valuable chemicals using renewable energy sources. Recent advances have centered on fine‐tuning catalyst materials and their micro‐environments, stimulating interest within the CO2R community. However, testing novel catalyst materials often occurs under conditions different from those relevant to industrial applications. In this study, we explore the transferability of CO2R results obtained using Ag‐based gas diffusion electrode (GDEs) in an easy to fabricate, assemble and test zero‐gap half‐cell (ZGHC) to a zero‐gap electrolyzer (ZGE). Our investigation reveals that the transferability of results is not only influenced by the reactor design, but also partially dependent on the type of additive used in the catalyst layer of the GDE. Moreover, we show that the humidity of the CO2 is a crucial operational parameter that not only impacts the selectivity of the electrode but also influences its stability during testing in the ZGHC. These findings highlight the importance of comprehensively considering operational conditions as well as reactor designs when comparing results between the ZGHC and ZGE, presenting finally a pathway on how to minimize such differences.
- 26 January 2024
- Published by Wiley in ChemElectroChem
- Vol. 11 (5)
Open AccessExploring the (Dis)‐Similarities of Half‐Cell and Full Cell Zero‐Gap Electrolyzers for the CO2 Electroreduction
Carbon dioxide electroreduction (CO2R) is a promising technology for mitigating industrial CO2 emissions and generating valuable chemicals using renewable energy sources. Recent advances have centered on fine‐tuning catalyst materials and their micro‐environments, stimulating interest within the CO2R community. However, testing novel catalyst materials often occurs under conditions different from those relevant to industrial applications. In this study, we explore the transferability of CO2R results obtained using Ag‐based gas diffusion electrode (GDEs) in an easy to fabricate, assemble and test zero‐gap half‐cell (ZGHC) to a zero‐gap electrolyzer (ZGE). Our investigation reveals that the transferability of results is not only influenced by the reactor design, but also partially dependent on the type of additive used in the catalyst layer of the GDE. Moreover, we show that the humidity of the CO2 is a crucial operational parameter that not only impacts the selectivity of the electrode but also influences its stability during testing in the ZGHC. These findings highlight the importance of comprehensively considering operational conditions as well as reactor designs when comparing results between the ZGHC and ZGE, presenting finally a pathway on how to minimize such differences.