Bing Zhou
Bing Zhou has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Ce Zhao
Shanghai New Era Airport Design & Research Institute Co., Ltd. of CAAC, Shanghai 200000, China
1 shared publication - Fei Liu
Key Laboratory of Road and Traffic Engineering, Ministry of Education, Tongji University, Shanghai 201804, China
1 shared publication - Feilin Zhang
Shanghai New Era Airport Design & Research Institute Co., Ltd. of CAAC, Shanghai 200000, China
1 shared publication - Haihua Zhang
Department of Geotechnical Engineering, Tongji University, Shanghai 200092, China
1 shared publication - Huacheng Jiao
Key Laboratory of Road and Traffic Engineering, Ministry of Education, Tongji University, Shanghai 201804, China
1 shared publication - Jiafeng Zhang
Shanghai CAAC New Era Airport Design & Research Institute Co., Ltd., Shanghai 200335, China
1 shared publication
Latest Publications
- Open Access
Experimental Study on Dual-Structure Polymer Optical Fiber Sensors for Turbidity Detection
This study presents a comprehensive investigation of turbidity monitoring using two different types of polymer optical fiber (POF) sensors: the reflection–refraction type (RR-POF) and the gap type (Gap-POF). Both sensors were used to visualize and monitor the turbidity changes in suspensions with varying concentrations and different particle compositions, namely silica powder and clay particles. The experiments were conducted by introducing silica powder and clay into water at various concentrations, and the resulting turbidity was measured using both types of POF sensors. The results revealed a significant correlation between particle concentration and light intensity for both kinds of POF sensors. As the particle concentration increased, the light intensity decreased due to increased scattering and absorption effects. For both silica powder and clay suspensions, the light intensity stabilized at lower values as the concentration increased, with the Gap-POF sensor exhibiting higher sensitivity to turbidity changes, particularly at high particle concentrations. Additionally, the study found that the particle composition influenced the sensor response. Silica powder particles caused more irregular fluctuations in light intensity at higher concentrations due to their larger particle size and tendency to aggregate, while clay particles, due to their smaller size and better dispersion, resulted in more stable and gradual changes in light intensity. This highlighted the differences in optical responses between different particle types. Furthermore, the multi-wavelength measurements showed consistent results, with white and green lights exhibiting the strongest response to turbidity changes, while red and blue lights were less sensitive. This wavelength-dependent response was attributed to the scattering and absorption properties of the particles in the suspensions. Both RR-POF and Gap-POF sensors proved to be effective for turbidity monitoring, with Gap-POF demonstrating superior performance in high-concentration suspensions. The findings suggest that POF sensors, particularly Gap-POF, are highly suitable for real-time turbidity monitoring in various particle suspension systems.
Open AccessExperimental Study on Dual-Structure Polymer Optical Fiber Sensors for Turbidity Detection
This study presents a comprehensive investigation of turbidity monitoring using two different types of polymer optical fiber (POF) sensors: the reflection–refraction type (RR-POF) and the gap type (Gap-POF). Both sensors were used to visualize and monitor the turbidity changes in suspensions with varying concentrations and different particle compositions, namely silica powder and clay particles. The experiments were conducted by introducing silica powder and clay into water at various concentrations, and the resulting turbidity was measured using both types of POF sensors. The results revealed a significant correlation between particle concentration and light intensity for both kinds of POF sensors. As the particle concentration increased, the light intensity decreased due to increased scattering and absorption effects. For both silica powder and clay suspensions, the light intensity stabilized at lower values as the concentration increased, with the Gap-POF sensor exhibiting higher sensitivity to turbidity changes, particularly at high particle concentrations. Additionally, the study found that the particle composition influenced the sensor response. Silica powder particles caused more irregular fluctuations in light intensity at higher concentrations due to their larger particle size and tendency to aggregate, while clay particles, due to their smaller size and better dispersion, resulted in more stable and gradual changes in light intensity. This highlighted the differences in optical responses between different particle types. Furthermore, the multi-wavelength measurements showed consistent results, with white and green lights exhibiting the strongest response to turbidity changes, while red and blue lights were less sensitive. This wavelength-dependent response was attributed to the scattering and absorption properties of the particles in the suspensions. Both RR-POF and Gap-POF sensors proved to be effective for turbidity monitoring, with Gap-POF demonstrating superior performance in high-concentration suspensions. The findings suggest that POF sensors, particularly Gap-POF, are highly suitable for real-time turbidity monitoring in various particle suspension systems.
- Open Access
Research on Mechanical Properties of Cement Emulsified Asphalt Mortar Under the Influence of Water-to-Cement Ratios and Water-Reducing Agent
To understand the mechanical behavior of CRTS (China Railway Track System) II cement emulsified asphalt mortar (CA mortar), this study tested the compressive strength and flexural strength of CA mortar at different ages under varying water-to-cement ratios and dosages of water-reducing agent. Based on X-ray diffraction (XRD) and scanning electron microscopy (SEM) results, the hydration products and microstructure of CA mortar at different ages were analyzed. The main conclusions are as follows. As the water-to-cement ratio increases, the compressive strength and flexural strength of CA mortar generally exhibit a decreasing trend. The strength increases rapidly in the early stages, with the 7-day compressive strength reaching over 80% of the 28-day compressive strength, and the 7-day flexural strength reaching over 93% of the 28-day flexural strength. As the dosage of water-reducing agent increases, both the compressive strength and flexural strength of CA mortar first increase and then decrease, with a reasonable range of water-reducing agent dosage being between 0.2% and 1.0%, and 0.5% is most appropriate. The hydration reaction of CA mortar is nearly complete at 3 days, with the increase in ages, the cement hydration slows down due to the coating action of asphalt, and the strength no longer changes greatly. Hydration products are mainly Ettringite, which is the main source of strength of CA mortar. After the emulsified asphalt breaks, it adsorbs onto the hydration products and sand surfaces, gradually forming a continuous phase, which enhances the structural toughness of the CA mortar.
Open AccessResearch on Mechanical Properties of Cement Emulsified Asphalt Mortar Under the Influence of Water-to-Cement Ratios and Water-Reducing Agent
To understand the mechanical behavior of CRTS (China Railway Track System) II cement emulsified asphalt mortar (CA mortar), this study tested the compressive strength and flexural strength of CA mortar at different ages under varying water-to-cement ratios and dosages of water-reducing agent. Based on X-ray diffraction (XRD) and scanning electron microscopy (SEM) results, the hydration products and microstructure of CA mortar at different ages were analyzed. The main conclusions are as follows. As the water-to-cement ratio increases, the compressive strength and flexural strength of CA mortar generally exhibit a decreasing trend. The strength increases rapidly in the early stages, with the 7-day compressive strength reaching over 80% of the 28-day compressive strength, and the 7-day flexural strength reaching over 93% of the 28-day flexural strength. As the dosage of water-reducing agent increases, both the compressive strength and flexural strength of CA mortar first increase and then decrease, with a reasonable range of water-reducing agent dosage being between 0.2% and 1.0%, and 0.5% is most appropriate. The hydration reaction of CA mortar is nearly complete at 3 days, with the increase in ages, the cement hydration slows down due to the coating action of asphalt, and the strength no longer changes greatly. Hydration products are mainly Ettringite, which is the main source of strength of CA mortar. After the emulsified asphalt breaks, it adsorbs onto the hydration products and sand surfaces, gradually forming a continuous phase, which enhances the structural toughness of the CA mortar.
- Open Access
- 8 February 2024
- Published by HARD Publishing Company in Polish Journal of Environmental Studies
- Vol. 33 (3) , 2603-2611
Comparative Study on Bearing Capacity of Unsaturated Cohesive Soil at High Plateau Airport
The study focuses on the unsaturated cohesive soil of a high-plateau airport in the southwest mountainous area of China, and the standard penetration tests, laboratory tests, and static cone penetration tests were respectively adopted to carry out a comparative study on the bearing capacity of the foundation soil. The results showed that among the three testing methods, the static cone penetration test method yielded the highest bearing capacity values, The bearing capacity determined by the laboratory test was secondary, and the bearing capacity determined by the standard penetration test method was the minimum. The bearing capacity value determined by the standard penetration test was close to the laboratory test method, and the difference value was not more than 5%. The difference between the static test method and the other two methods was more than 5%. For the studied soil samples, it is suggested that the bearing capacity value should be determined by the standard penetration test method or the laboratory test method, but the static test method is not recommended. The results have some theoretical guidance and practical significance for the analysis of engineering characteristics for the same type of soil.
- 8 February 2024
- Published by HARD Publishing Company in Polish Journal of Environmental Studies
- Vol. 33 (3) , 2603-2611
Open AccessComparative Study on Bearing Capacity of Unsaturated Cohesive Soil at High Plateau Airport
The study focuses on the unsaturated cohesive soil of a high-plateau airport in the southwest mountainous area of China, and the standard penetration tests, laboratory tests, and static cone penetration tests were respectively adopted to carry out a comparative study on the bearing capacity of the foundation soil. The results showed that among the three testing methods, the static cone penetration test method yielded the highest bearing capacity values, The bearing capacity determined by the laboratory test was secondary, and the bearing capacity determined by the standard penetration test method was the minimum. The bearing capacity value determined by the standard penetration test was close to the laboratory test method, and the difference value was not more than 5%. The difference between the static test method and the other two methods was more than 5%. For the studied soil samples, it is suggested that the bearing capacity value should be determined by the standard penetration test method or the laboratory test method, but the static test method is not recommended. The results have some theoretical guidance and practical significance for the analysis of engineering characteristics for the same type of soil.