Amin Aghighi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Amin Aghighi has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Mostafa Essawy
School of Electrical Engineering and Computer Science, Oregon State University, Corvallis, OR, USA
2 shared publications - Arun Natarajan
School of Electrical Engineering and Computer Science, Oregon State University, Corvallis, OR, USA
1 shared publication Arun S. Natarajan
School of Electrical Engineering and Computer Science, Oregon State University, Corvallis, OR, USA
1 shared publication- Kareem Rashed
School of Electrical Engineering and Computer Science, Oregon State University, Corvallis, OR, USA
1 shared publication
Latest Publications
- 29 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (5) , 2704-2715
A Frequency Doubler With Second Harmonic Feedback for Wideband, Efficient Frequency Multiplication at Millimeter-Wave
Frequency multipliers are widely used in scalable millimeter-wave (mm-wave) arrays in communication and radar. This article presents an mm-wave frequency doubler (FDB) topology that exploits odd-mode/even-mode operation to create different feedback networks at the fundamental frequency and second harmonic. Theoretical analysis of the FDB network is detailed. The FDB topology is well-suited for CMOS integration, and a stand-alone FDB in 65-nm CMOS achieves a saturated output power ( $\boldsymbol{P_{\text{sat}}}$ ) of $\boldsymbol{>}$ 10.1 dBm with a maximum drain efficiency (DE) of 32.7% at 60 GHz. The wideband FDB is also cascaded with a power amplifier (PA) to achieve a total $\boldsymbol{P_{\text{sat}}}$ of 15 dBm with a maximum dc-to-RF efficiency ( $\boldsymbol{\eta_{\text{total}}}$ ) of 24.5%. Measurements demonstrate wideband FDB chirp bandwidths and suitability for frequency-modulated continuous wave (FMCW) radar applications.
- 29 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (5) , 2704-2715
A Frequency Doubler With Second Harmonic Feedback for Wideband, Efficient Frequency Multiplication at Millimeter-Wave
Frequency multipliers are widely used in scalable millimeter-wave (mm-wave) arrays in communication and radar. This article presents an mm-wave frequency doubler (FDB) topology that exploits odd-mode/even-mode operation to create different feedback networks at the fundamental frequency and second harmonic. Theoretical analysis of the FDB network is detailed. The FDB topology is well-suited for CMOS integration, and a stand-alone FDB in 65-nm CMOS achieves a saturated output power ( $\boldsymbol{P_{\text{sat}}}$ ) of $\boldsymbol{>}$ 10.1 dBm with a maximum drain efficiency (DE) of 32.7% at 60 GHz. The wideband FDB is also cascaded with a power amplifier (PA) to achieve a total $\boldsymbol{P_{\text{sat}}}$ of 15 dBm with a maximum dc-to-RF efficiency ( $\boldsymbol{\eta_{\text{total}}}$ ) of 24.5%. Measurements demonstrate wideband FDB chirp bandwidths and suitability for frequency-modulated continuous wave (FMCW) radar applications.
- 8 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (5) , 1337-1350
A Low-Noise Dual-Path Self-Interference Cancellation Architecture for Watt-Level TX Power Handling in Simultaneous Transmit and Receive
Mitigating self-interference (SI) is vital for advancing simultaneous transmit and receive (STAR) systems. The noise and linearity of the canceller impose limitations on SI power handling. This article proposes a novel dual-path SI cancelling scheme for high-power SI handling. The proposed approach breaks self-interference cancellation (SIC) tradeoffs between operating frequency, SI power handling, and canceller noise/distortion by using a frequency-translated (FT) SI canceller and an auxiliary FT noise-cancelling (NC) path that cancels the noise/distortion from the primary canceller. This approach can work well for both full-duplex (FD) and frequency-division duplex (FDD) schemes. The 65-nm CMOS implementation achieves ~45-dB SIC for 12-dBm receiver (RX) SI peak power (9-dBm avg.) with only 4-dB noise figure (NF) degradation and 207-mW power consumption at 600 MHz. The SIC approach enables a blocker-1 dB with respect to SI of > 16 dBm ( $8\times $ higher than prior work) while operating from 0.5 to 1.3 GHz. Therefore, this implementation can support watt-level SI power handling with transmitter (TX)–RX isolation > 15 dB. This is demonstrated through measurements that show 30-dBm TX power handling with 22-dB initial isolation from the circulator.
- 8 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (5) , 1337-1350
A Low-Noise Dual-Path Self-Interference Cancellation Architecture for Watt-Level TX Power Handling in Simultaneous Transmit and Receive
Mitigating self-interference (SI) is vital for advancing simultaneous transmit and receive (STAR) systems. The noise and linearity of the canceller impose limitations on SI power handling. This article proposes a novel dual-path SI cancelling scheme for high-power SI handling. The proposed approach breaks self-interference cancellation (SIC) tradeoffs between operating frequency, SI power handling, and canceller noise/distortion by using a frequency-translated (FT) SI canceller and an auxiliary FT noise-cancelling (NC) path that cancels the noise/distortion from the primary canceller. This approach can work well for both full-duplex (FD) and frequency-division duplex (FDD) schemes. The 65-nm CMOS implementation achieves ~45-dB SIC for 12-dBm receiver (RX) SI peak power (9-dBm avg.) with only 4-dB noise figure (NF) degradation and 207-mW power consumption at 600 MHz. The SIC approach enables a blocker-1 dB with respect to SI of > 16 dBm ( $8\times $ higher than prior work) while operating from 0.5 to 1.3 GHz. Therefore, this implementation can support watt-level SI power handling with transmitter (TX)–RX isolation > 15 dB. This is demonstrated through measurements that show 30-dBm TX power handling with 22-dB initial isolation from the circulator.