Leslie Bromberg
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Leslie Bromberg has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- Joseph V. Minervini
Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, MA, USA
4 shared publications - Makoto Takayasu
PSFC, MIT, Cambridge, MA, USA
3 shared publications - Mohammad Ostadi
Department of Energy, Aalborg University, 6700 Esbjerg, Denmark
3 shared publications - Philip C. Michael
Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, MA, USA
3 shared publications - Daniel R. Cohn
MIT Energy Initiative, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA 02139, USA
2 shared publications - Guiyan Zang
MIT Energy Initiative, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA 02139, USA
2 shared publications
Latest Publications
- Open Access
- 10 November 2025
- Published by Office of Scientific and Technical Information (OSTI)
HTS to NbTi Joints for Fusion Magnet Cost Savings
This paper describes methods of employing high field High Temperature Superconductors (HTS), only where high field capability and high current density is needed in superconducting coils. The approach lends itself, in particular, to Toroidal Field (TF) coils used in fusion reactors. The initial idea was to develop a conductor joint design or designs that would allow joints between expensive high field High Temperature Superconductors (HTS) Rare Earth Barium Copper Oxide (REBCO) conductors to low cost NbTi lower field conductors. Grading options are available for accommodating field gradients from the high field side of a magnet to the low field side of the magnet. Regionalizing the type of conductor used such that high field conductors are only used at the plasma side of a Toroidal Field (TF) winding pack, allows the use of less expensive conductors on the low field side. This is commonly done in reactor studies. The Toroidal field is proportional to 1/r, and this field decrease also provides an opportunity for grading. For example, a Tokamak with 7T at the center of the plasma (Ro) and 20 T in the inner corner only needs the higher field capability at the inner radii of the machine. This suggests transitions with joints from high field to low field conductors. Another option with stacked tapes is to gradually replace superconducting tapes with Hastelloy tapes as the field drops, but this is also a jointed approach relying on conduction through the steel tapes. In this paper, two possible joints are considered, a local soldered NbTi to REBCO stacked tape joint and a shunt design in which currents flow in a clamped copper shell which is laced with HTS. Space needs, resistance and cooling requirements are addressed. Some characteristics of the joints effecting quench are discussed. In stellarator coils, certain of the tight turn geometries in the “potato chip” coils produce local high fields and require compact winding packs to allow the required turn radius. Other portions of these coils can have larger cross sections and would allow lower field conductor types in selected regions.
- 10 November 2025
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessHTS to NbTi Joints for Fusion Magnet Cost Savings
This paper describes methods of employing high field High Temperature Superconductors (HTS), only where high field capability and high current density is needed in superconducting coils. The approach lends itself, in particular, to Toroidal Field (TF) coils used in fusion reactors. The initial idea was to develop a conductor joint design or designs that would allow joints between expensive high field High Temperature Superconductors (HTS) Rare Earth Barium Copper Oxide (REBCO) conductors to low cost NbTi lower field conductors. Grading options are available for accommodating field gradients from the high field side of a magnet to the low field side of the magnet. Regionalizing the type of conductor used such that high field conductors are only used at the plasma side of a Toroidal Field (TF) winding pack, allows the use of less expensive conductors on the low field side. This is commonly done in reactor studies. The Toroidal field is proportional to 1/r, and this field decrease also provides an opportunity for grading. For example, a Tokamak with 7T at the center of the plasma (Ro) and 20 T in the inner corner only needs the higher field capability at the inner radii of the machine. This suggests transitions with joints from high field to low field conductors. Another option with stacked tapes is to gradually replace superconducting tapes with Hastelloy tapes as the field drops, but this is also a jointed approach relying on conduction through the steel tapes. In this paper, two possible joints are considered, a local soldered NbTi to REBCO stacked tape joint and a shunt design in which currents flow in a clamped copper shell which is laced with HTS. Space needs, resistance and cooling requirements are addressed. Some characteristics of the joints effecting quench are discussed. In stellarator coils, certain of the tight turn geometries in the “potato chip” coils produce local high fields and require compact winding packs to allow the required turn radius. Other portions of these coils can have larger cross sections and would allow lower field conductor types in selected regions.
- Open Access
- 21 June 2025
- Published by MDPI AG in Sustainability
- Vol. 17 (13) , 5718
Potential Expansion of Low-Carbon Liquid Fuel Production Using Hydrogen-Enhanced Biomass/Municipal Solid Waste Gasification
Low-carbon liquid fuels are needed for decarbonization of hard-to-decarbonize segments of the transportation sector. This decarbonization can be limited by the amount of renewable carbon. Thermochemical conversion of biomass/municipal solid waste (MSW) through gasification is a promising route for producing low-carbon fuels. There are two major opportunities for increasing the amount of low-carbon liquid fuel that can be produced from gasification in any region. One is to increase the amount of liquid fuel from a given amount of biomass/MSW, particularly by hydrogen-enhancement of gasification synthesis gas. Second is the potential for large expansion of use of biomass feedstocks from its present level. Such biomass feedstocks include agricultural waste, forestry waste, MSW, and specially grown biomass that does not interfere with food production. The use of MSW may provide advantages of an established network for pickup and transportation of feedstock to disposal sites and the avoidance of methane produced from landfilling of MSW. As a case study, we looked at potential expansion of US low-carbon fuel production, considering the recent projections of the 2024 USDOE report, which estimated potential production of a billion tons/yr of biomass/MSW feedstocks in the US. This report included an estimated potential for liquid biofuel production of 60 billion gallons/yr of diesel energy equivalent fuel without the use of hydrogen enhancement. By hydrogen-enhanced biomass/MSW gasification, this projection could be doubled to 120 billion gallons/yr of diesel energy equivalent fuel. Furthermore, the co-location potential of biomass/MSW resources with potential renewable energy generation sites is explored. This overlap of hydrogen production and biomass production in the US are located in regions such as the US Midwest, Texas, and California. This co-location strategy enhances logistical feasibility, reducing transport costs and optimizing energy system integration; and can be applied to other geographical locations. Hydrogen-enhanced biomass/MSW gasification offers a promising route to substantially increase low-carbon liquid fuel production (e.g., methanol) and support increased liquid fuel production and greenhouse gas reduction goals.
- 21 June 2025
- Published by MDPI AG in Sustainability
- Vol. 17 (13) , 5718
Open AccessPotential Expansion of Low-Carbon Liquid Fuel Production Using Hydrogen-Enhanced Biomass/Municipal Solid Waste Gasification
Low-carbon liquid fuels are needed for decarbonization of hard-to-decarbonize segments of the transportation sector. This decarbonization can be limited by the amount of renewable carbon. Thermochemical conversion of biomass/municipal solid waste (MSW) through gasification is a promising route for producing low-carbon fuels. There are two major opportunities for increasing the amount of low-carbon liquid fuel that can be produced from gasification in any region. One is to increase the amount of liquid fuel from a given amount of biomass/MSW, particularly by hydrogen-enhancement of gasification synthesis gas. Second is the potential for large expansion of use of biomass feedstocks from its present level. Such biomass feedstocks include agricultural waste, forestry waste, MSW, and specially grown biomass that does not interfere with food production. The use of MSW may provide advantages of an established network for pickup and transportation of feedstock to disposal sites and the avoidance of methane produced from landfilling of MSW. As a case study, we looked at potential expansion of US low-carbon fuel production, considering the recent projections of the 2024 USDOE report, which estimated potential production of a billion tons/yr of biomass/MSW feedstocks in the US. This report included an estimated potential for liquid biofuel production of 60 billion gallons/yr of diesel energy equivalent fuel without the use of hydrogen enhancement. By hydrogen-enhanced biomass/MSW gasification, this projection could be doubled to 120 billion gallons/yr of diesel energy equivalent fuel. Furthermore, the co-location potential of biomass/MSW resources with potential renewable energy generation sites is explored. This overlap of hydrogen production and biomass production in the US are located in regions such as the US Midwest, Texas, and California. This co-location strategy enhances logistical feasibility, reducing transport costs and optimizing energy system integration; and can be applied to other geographical locations. Hydrogen-enhanced biomass/MSW gasification offers a promising route to substantially increase low-carbon liquid fuel production (e.g., methanol) and support increased liquid fuel production and greenhouse gas reduction goals.
- Open Access
- 6 October 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (19) , 8649
CH4 and CO2 Reductions from Methanol Production Using Municipal Solid Waste Gasification with Hydrogen Enhancement
This study evaluates the greenhouse gas (GHG) impacts of converting municipal solid waste (MSW) into methanol, focusing on both landfill methane (CH4) emission avoidance and the provision of cleaner liquid fuels with lower carbon intensity. We conduct a life cycle assessment (LCA) to assess potential GHG reductions from MSW gasification to methanol, enhanced with hydrogen produced via natural gas pyrolysis or water electrolysis. Hydrogen enhancement effectively doubles the methanol yield from a given amount of MSW. Special attention is given to hydrogen production through natural gas pyrolysis due to its potential for lower-cost hydrogen and reduced reliance on renewable electricity compared to electrolytic hydrogen. Our analysis uses a case study of methanol production from an oxygen-fired entrained flow gasifier fed with refuse-derived fuel (RDF) simulated in Aspen HYSYS. The LCA incorporates the significant impact of landfill methane avoidance, particularly when considering the 20-year global warming potential (GWP). Based on the LCA, the process has illustrative net GHG emissions of 183 and 709 kgCO2e/t MeOH using renewable electricity for electrolytic hydrogen and pyrolytic hydrogen, respectively, for the 100-year GWP. The net GHG emissions using 20-year GWP are −1222 and −434 kgCO2e/t MeOH, respectively. Additionally, we analyze the sensitivity of net GHG emissions to varying levels of fugitive methane emissions.
- 6 October 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (19) , 8649
Open AccessCH4 and CO2 Reductions from Methanol Production Using Municipal Solid Waste Gasification with Hydrogen Enhancement
This study evaluates the greenhouse gas (GHG) impacts of converting municipal solid waste (MSW) into methanol, focusing on both landfill methane (CH4) emission avoidance and the provision of cleaner liquid fuels with lower carbon intensity. We conduct a life cycle assessment (LCA) to assess potential GHG reductions from MSW gasification to methanol, enhanced with hydrogen produced via natural gas pyrolysis or water electrolysis. Hydrogen enhancement effectively doubles the methanol yield from a given amount of MSW. Special attention is given to hydrogen production through natural gas pyrolysis due to its potential for lower-cost hydrogen and reduced reliance on renewable electricity compared to electrolytic hydrogen. Our analysis uses a case study of methanol production from an oxygen-fired entrained flow gasifier fed with refuse-derived fuel (RDF) simulated in Aspen HYSYS. The LCA incorporates the significant impact of landfill methane avoidance, particularly when considering the 20-year global warming potential (GWP). Based on the LCA, the process has illustrative net GHG emissions of 183 and 709 kgCO2e/t MeOH using renewable electricity for electrolytic hydrogen and pyrolytic hydrogen, respectively, for the 100-year GWP. The net GHG emissions using 20-year GWP are −1222 and −434 kgCO2e/t MeOH, respectively. Additionally, we analyze the sensitivity of net GHG emissions to varying levels of fugitive methane emissions.
- 4 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 29 (5) , 1-5
Re-Makeable Joint With Insulation for REBCO Superconductor Cables
Composite Technology Development, Inc. (CTD), in partnership with the Plasma Science and Fusion Center (PSFC) at MIT recently developed and demonstrated a re-makeable, insulated HTS cable joint for a Twisted Stacked-Tape Cable (TSTC). The prototype joint exhibited low tape-to-tape resistances $(\rm \sim 400 n\Omega)$ with critical current through the joint for most tape pairs matching that of the as-supplied conductor tape $(\rm I_c = 142 A)$ . The best performing insulation scheme showed dielectric withstand voltage in excess of 10 kV. Disassembly and reassembly of the joint showed no degradation in performance.- 4 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 29 (5) , 1-5
Re-Makeable Joint With Insulation for REBCO Superconductor Cables
Composite Technology Development, Inc. (CTD), in partnership with the Plasma Science and Fusion Center (PSFC) at MIT recently developed and demonstrated a re-makeable, insulated HTS cable joint for a Twisted Stacked-Tape Cable (TSTC). The prototype joint exhibited low tape-to-tape resistances $(\rm \sim 400 n\Omega)$ with critical current through the joint for most tape pairs matching that of the as-supplied conductor tape $(\rm I_c = 142 A)$ . The best performing insulation scheme showed dielectric withstand voltage in excess of 10 kV. Disassembly and reassembly of the joint showed no degradation in performance.- 9 July 2018
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 140 (11)
Catalyst Ammonia Storage Measurements Using Radio Frequency Sensing1
Motivated by increasingly strict nitrogen oxides (NOx) limits, engine manufacturers have adopted selective catalytic reduction (SCR) technology to reduce engine-out NOx. In the SCR process, NOx react with ammonia (NH3) to form nitrogen and water vapor. The reaction is influenced by several variables, including stored ammonia on the catalyst, exhaust gas composition, and catalyst temperature. Currently, measurements from NOx and/or NH3 sensors upstream and downstream of the SCR are used with predictive models to estimate ammonia storage levels on the catalyst and control urea dosing. This study investigated a radio frequency (RF)-based method to directly monitor the ammonia storage state of the SCR. This approach utilizes the catalyst as a cavity resonator, in which an RF antenna excites electromagnetic waves within the cavity to monitor changes in the catalyst state. Ammonia storage causes changes in the dielectric properties of the catalyst, which directly impacts the RF signal. Changes in the RF signal relative to stored ammonia (NH3) were evaluated over a wide range of frequencies, temperatures, and exhaust conditions. The RF response to NH3 storage, desorption, and oxidation on the SCR was well correlated with changes in the catalyst state. Calibrated RF measurements demonstrate the ability to monitor the adsorption state of the SCR to within 10% of the sensor full scale. The results indicate direct measurement of SCR ammonia storage levels, and resulting catalyst feedback control, via RF sensing to have significant potential for optimizing the SCR system to improve NOx conversion and decrease urea consumption.
- 9 July 2018
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 140 (11)
Catalyst Ammonia Storage Measurements Using Radio Frequency Sensing1
Motivated by increasingly strict nitrogen oxides (NOx) limits, engine manufacturers have adopted selective catalytic reduction (SCR) technology to reduce engine-out NOx. In the SCR process, NOx react with ammonia (NH3) to form nitrogen and water vapor. The reaction is influenced by several variables, including stored ammonia on the catalyst, exhaust gas composition, and catalyst temperature. Currently, measurements from NOx and/or NH3 sensors upstream and downstream of the SCR are used with predictive models to estimate ammonia storage levels on the catalyst and control urea dosing. This study investigated a radio frequency (RF)-based method to directly monitor the ammonia storage state of the SCR. This approach utilizes the catalyst as a cavity resonator, in which an RF antenna excites electromagnetic waves within the cavity to monitor changes in the catalyst state. Ammonia storage causes changes in the dielectric properties of the catalyst, which directly impacts the RF signal. Changes in the RF signal relative to stored ammonia (NH3) were evaluated over a wide range of frequencies, temperatures, and exhaust conditions. The RF response to NH3 storage, desorption, and oxidation on the SCR was well correlated with changes in the catalyst state. Calibrated RF measurements demonstrate the ability to monitor the adsorption state of the SCR to within 10% of the sensor full scale. The results indicate direct measurement of SCR ammonia storage levels, and resulting catalyst feedback control, via RF sensing to have significant potential for optimizing the SCR system to improve NOx conversion and decrease urea consumption.
- 3 April 2018
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Optimized PFI+DI Operation For Minimizing DI Gasoline Engine Particulates
Direct Injection (DI) fueled gasoline engines provide higher efficiency than port fueled injected (PFI) engines. However, emission of small particulates is greatly increased when DI is used. Particulate mass emission is increased by more than a factor of 10 and particulate number is increased by a factor of 10-100 relative to PFI engines leading to health concerns and to implementation and consideration of new regulations.Optimized combinations of PFI and DI can greatly reduce DI-generated particulate emissions without compromising efficiency and performance. A DI enhanced PFI mode of engine operation is employed where PFI is the dominant means in dual-injection fueling over a drive cycle, and the fuel fraction that is directly injected is reduced/minimized while still preventing knock at high loads. Further reduction can be obtained by optimal use of spark retard. The already low particulate emissions are further reduced by decreasing the percentage of DI fuel that results in particulate generation from wall wetting; this is accomplished by adjustment of injection timing, injection rate and pulse length.We have developed a computational model of DI-generated particulates over the torque and speed map for gasoline engine operation with combined PFI and DI. The computational model includes models for knock suppression and for particulate generation from wall wetting. These models are calibrated using experimental data. We have used this computational approach to determine illustrative reductions in DI generated particulates for turbocharged gasoline engines various drive cycles. These reductions in DI-generated particulates for the US06 and UDDS cycles are greater than 20 and 50 times, respectively relative to the use of DI alone. An optimized PFI+DI system could be used in combination with a GPF for even further particulate reduction while also reducing GPF cost and the efficiency loss from GPF back pressure.
- 3 April 2018
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Optimized PFI+DI Operation For Minimizing DI Gasoline Engine Particulates
Direct Injection (DI) fueled gasoline engines provide higher efficiency than port fueled injected (PFI) engines. However, emission of small particulates is greatly increased when DI is used. Particulate mass emission is increased by more than a factor of 10 and particulate number is increased by a factor of 10-100 relative to PFI engines leading to health concerns and to implementation and consideration of new regulations.Optimized combinations of PFI and DI can greatly reduce DI-generated particulate emissions without compromising efficiency and performance. A DI enhanced PFI mode of engine operation is employed where PFI is the dominant means in dual-injection fueling over a drive cycle, and the fuel fraction that is directly injected is reduced/minimized while still preventing knock at high loads. Further reduction can be obtained by optimal use of spark retard. The already low particulate emissions are further reduced by decreasing the percentage of DI fuel that results in particulate generation from wall wetting; this is accomplished by adjustment of injection timing, injection rate and pulse length.We have developed a computational model of DI-generated particulates over the torque and speed map for gasoline engine operation with combined PFI and DI. The computational model includes models for knock suppression and for particulate generation from wall wetting. These models are calibrated using experimental data. We have used this computational approach to determine illustrative reductions in DI generated particulates for turbocharged gasoline engines various drive cycles. These reductions in DI-generated particulates for the US06 and UDDS cycles are greater than 20 and 50 times, respectively relative to the use of DI alone. An optimized PFI+DI system could be used in combination with a GPF for even further particulate reduction while also reducing GPF cost and the efficiency loss from GPF back pressure.
- 20 November 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 25 (3) , 1-5
Design and Test of a Prototype 20 kA HTS DC Power Transmission Cable
We present an innovative design for a high temperature superconductor (HTS) dc power transmission system containing an HTS cable connected to optimized multistage current leads and cooled by a multistage turbo-Brayton cryocooler. Analytical results indicate that our proposed 5 MW transmission system can provide a 35% reduction in transmission losses and 93% reduction in system weight, compared with ambient-temperature copper bus. We describe a test stand to assess the performance of the proposed design and discus modifications to the facility to permit cable testing at up to 20 kA current. Efforts to demonstrate full current operation in the simulated system were hampered by higher than expected electrical resistance at the cable joints.
- 20 November 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 25 (3) , 1-5
Design and Test of a Prototype 20 kA HTS DC Power Transmission Cable
We present an innovative design for a high temperature superconductor (HTS) dc power transmission system containing an HTS cable connected to optimized multistage current leads and cooled by a multistage turbo-Brayton cryocooler. Analytical results indicate that our proposed 5 MW transmission system can provide a 35% reduction in transmission losses and 93% reduction in system weight, compared with ambient-temperature copper bus. We describe a test stand to assess the performance of the proposed design and discus modifications to the facility to permit cable testing at up to 20 kA current. Efforts to demonstrate full current operation in the simulated system were hampered by higher than expected electrical resistance at the cable joints.
- 21 February 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 23 (3) , 6200805
DC Superconducting Cable Using $\hbox{MgB}_{2}$ WiresTsinghua University, University of Cambridge, and MIT are collaborating to design, construct, and test an MgB 2 dc cable for microgrid applications. Two-stage current leads with nitrogen vapor cooled copper and gaseous helium cooled hightemperature superconductor will be used. The two-stage cryostat will be cooled using a single helium fan with a recuperator. The helium gas used to cool the MgB 2 to 20-25 K will be cooled with a two-stage GM cryocooler. The cryogenic stability of the cable will be presented. Designs of cryostats are being investigated. Semi-rigid cryostats, with low heat leak, are being designed and will be tested as part of this program. The system will operate up to 1 kV and 1 kA, limited by the present power equipment. However, the MgB 2 conductor is being designed for 5 kA, and may be tested at low voltage with upgraded current leads. A 30-m cable will be tested using facilities at Tsinghua University in Beijing.
- 21 February 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 23 (3) , 6200805
DC Superconducting Cable Using $\hbox{MgB}_{2}$ WiresTsinghua University, University of Cambridge, and MIT are collaborating to design, construct, and test an MgB 2 dc cable for microgrid applications. Two-stage current leads with nitrogen vapor cooled copper and gaseous helium cooled hightemperature superconductor will be used. The two-stage cryostat will be cooled using a single helium fan with a recuperator. The helium gas used to cool the MgB 2 to 20-25 K will be cooled with a two-stage GM cryocooler. The cryogenic stability of the cable will be presented. Designs of cryostats are being investigated. Semi-rigid cryostats, with low heat leak, are being designed and will be tested as part of this program. The system will operate up to 1 kV and 1 kA, limited by the present power equipment. However, the MgB 2 conductor is being designed for 5 kA, and may be tested at low voltage with upgraded current leads. A 30-m cable will be tested using facilities at Tsinghua University in Beijing.
- 1 January 2012
- Published by AIP Publishing in AIP Conference Proceedings
Current distribution and re-distribution in HTS cables made from 2nd generation tapes
Current redistribution in carpet-stack cables made from 2nd generation HTS tapes is investigated. In the carpet stack geometry tapes are stacked with their broad faces parallel to each other to build up a cable. Current redistribution in HTS cables is complex because the built-in insulation layer in each tape prevents effective current transfer between tapes. A method of shunting the tapes using periodically distributed superconducting bridges is investigated to improve current transfer, avoiding the need to solder the cable together. We calculate the mutual inductance between different tapes in a cable, and the effective resistance/transconductance for representative cable configurations. The effective time constants for current transfer and current redistribution are then calculated under different assumptions. We show that periodic shunting of the tapes using distributed superconducting bridges is an attractive method to achieve uniform current distribution in a HTS cable. The solution is flexible, and the performance of the system can be optimized by changing the width of shunt and/or the distance between shunts.
- 1 January 2012
- Published by AIP Publishing in AIP Conference Proceedings
Current distribution and re-distribution in HTS cables made from 2nd generation tapes
Current redistribution in carpet-stack cables made from 2nd generation HTS tapes is investigated. In the carpet stack geometry tapes are stacked with their broad faces parallel to each other to build up a cable. Current redistribution in HTS cables is complex because the built-in insulation layer in each tape prevents effective current transfer between tapes. A method of shunting the tapes using periodically distributed superconducting bridges is investigated to improve current transfer, avoiding the need to solder the cable together. We calculate the mutual inductance between different tapes in a cable, and the effective resistance/transconductance for representative cable configurations. The effective time constants for current transfer and current redistribution are then calculated under different assumptions. We show that periodic shunting of the tapes using distributed superconducting bridges is an attractive method to achieve uniform current distribution in a HTS cable. The solution is flexible, and the performance of the system can be optimized by changing the width of shunt and/or the distance between shunts.