Rasool Amini
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Rasool Amini has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Erfan Salahinejad
Faculty of Materials Science and Engineering, K. N. Toosi University of Technology, Tehran, Iran
2 shared publications M. Marasi
Department of Materials Science and Engineering, School of Engineering, Shiraz University, Zand Blvd., 7134851154 Shiraz, Iran
2 shared publications- Mohammad Jaffar Hadianfard
Department of Materials Science and Engineering, School of Engineering, Shiraz University, Shiraz, Iran
2 shared publications T. Sritharan
School of Materials Science and Engineering, Nanyang Technological University, Block N4.1, 50 Nanyang Avenue, 639798 Singapore, Singapore
2 shared publicationsAli Kemal Okyay
Department of Electrical and Electronics Engineering, UNAM-Institute of Materials Science and Nanotechnology Bilkent University, Ankara 06800, Turkey
1 shared publication- Fatemeh Alijani
Department of Materials Science and Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran
1 shared publication
Latest Publications
- 27 August 2019
- Published by SAGE Publications in Surface Engineering
- Vol. 35 (12) , 1088-1096
Effect of current density on Ni-Mo electrodeposition using EMIM [Br]
This study was conducted to investigate the current density impact on the Ni-Mo electrodeposit and on its catalytic activity of methanol oxidation in an alkaline solution. For this purpose, Ni-Mo coatings with good electrocatalytic properties were achieved by electrodeposition in the modified Watts bath containing 1-ethyl-3-methyl imidazolium bromide (EMIM [Br]) ionic liquid. The results showed that a 1–6 A dm−2 increase in the current density could decline the Mo content in the Ni-Mo/Ni coatings. The XRD patterns demonstrate that an amorphous coating formed with increasing the current density. Moreover, it was found that the catalytic performance of Ni-Mo coatings was significantly enhanced in the presence of methanol. Based on the obtained results, the Ni-Mo coating obtained at the current density of 3.5 A dm−2 and in the presence of EMIM [Br] showed a higher anodic current density, lower onset oxidation potential, and better catalytic performance.
- 27 August 2019
- Published by SAGE Publications in Surface Engineering
- Vol. 35 (12) , 1088-1096
Effect of current density on Ni-Mo electrodeposition using EMIM [Br]
This study was conducted to investigate the current density impact on the Ni-Mo electrodeposit and on its catalytic activity of methanol oxidation in an alkaline solution. For this purpose, Ni-Mo coatings with good electrocatalytic properties were achieved by electrodeposition in the modified Watts bath containing 1-ethyl-3-methyl imidazolium bromide (EMIM [Br]) ionic liquid. The results showed that a 1–6 A dm−2 increase in the current density could decline the Mo content in the Ni-Mo/Ni coatings. The XRD patterns demonstrate that an amorphous coating formed with increasing the current density. Moreover, it was found that the catalytic performance of Ni-Mo coatings was significantly enhanced in the presence of methanol. Based on the obtained results, the Ni-Mo coating obtained at the current density of 3.5 A dm−2 and in the presence of EMIM [Br] showed a higher anodic current density, lower onset oxidation potential, and better catalytic performance.
- 29 May 2012
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 538, 253-257
Quantitative phase evolution during mechano-synthesis of Ti–Ni–Cu shape memory alloys
- 29 May 2012
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 538, 253-257
Quantitative phase evolution during mechano-synthesis of Ti–Ni–Cu shape memory alloys
- 1 February 2010
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 527 (4-5) , 1135-1142
Characterization of Fe–Cr–Mn–N amorphous powders with a wide supercooled liquid region developed by mechanical alloying
- 1 February 2010
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 527 (4-5) , 1135-1142
Characterization of Fe–Cr–Mn–N amorphous powders with a wide supercooled liquid region developed by mechanical alloying
- 1 January 2009
- Published by Springer Nature in Journal of Materials Science
- Vol. 44 (1) , 136-148
Microstructural phase evaluation of high-nitrogen Fe–Cr–Mn alloy powders synthesized by the mechanical alloying process
- 1 January 2009
- Published by Springer Nature in Journal of Materials Science
- Vol. 44 (1) , 136-148
Microstructural phase evaluation of high-nitrogen Fe–Cr–Mn alloy powders synthesized by the mechanical alloying process