Torsten Brinkmann
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Torsten Brinkmann has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Sergey Shishatskiy
Institute of Membrane Research, Helmholtz-Zentrum Hereon, Max-Planck-Str. 1, 21502 Geesthacht, Germany
3 shared publications - Homa Hamedi
TU Dresden, Process Systems Engineering Group, Helmholtzstraße 10, 01069 Dresden, Germany
2 shared publications - Anja Drews
Department II Chemical Engineering in Life Science Engineering HTW Berlin—University of Applied Sciences Wilhelminenhofstraße 75A 12459 Berlin Germany
1 shared publication - Bernhard Schäfer
Karlsruher Institut für Technologie (KIT) Institut für Katalyseforschung & -technologie (IKFT) Hermann-von-Helmholtz-Platz 1 76344 Eggenstein-Leopoldshafen Deutschland
1 shared publication Eberhard Jochem
IREES GmbH – Institut für Ressourceneffizienz und Energiestrategien Schönfeldstraße 8 76131 Karlsruhe Deutschland
1 shared publicationFelipe Andrés Toro Chacón
IREES GmbH – Institut für Ressourceneffizienz und Energiestrategien Schönfeldstraße 8 76131 Karlsruhe Deutschland
1 shared publication
Latest Publications
- Open Access
- 2 September 2026
- Published by Elsevier in Journal of Membrane Science
- Vol. 759
Interpretable machine learning for predicting membrane performance of organic solvent nanofiltration membranes using an open-access database
- 2 September 2026
- Published by Elsevier in Journal of Membrane Science
- Vol. 759
Open AccessInterpretable machine learning for predicting membrane performance of organic solvent nanofiltration membranes using an open-access database
- 26 June 2024
- Published by Elsevier
- p. 577-582
Techno-Economic Analysis of H2 Extraction from Natural Gas Transmission Grids
- 26 June 2024
- Published by Elsevier
- p. 577-582
Techno-Economic Analysis of H2 Extraction from Natural Gas Transmission Grids
- Open Access
Permeance of Condensable Gases in Rubbery Polymer Membranes at High Pressure
The gas transport properties of thin film composite membranes (TFCMs) with selective layers of PolyActive™, polydimethylsiloxane (PDMS), and polyoctylmethylsiloxane (POMS) were investigated over a range of temperatures (10–34 °C; temperature increments of 2 °C) and pressures (1–65 bar abs; 38 pressure increments). The variation in the feed pressure of condensable gases CO2 and C2H6 enabled the observation of peaks of permeance in dependence on the feed pressure and temperature. For PDMS and POMS, the permeance peak was reproduced at the same feed gas activity as when the feed temperature was changed. PolyActive™ TFCM showed a more complex behaviour, most probably due to a higher CO2 affinity towards the poly(ethylene glycol) domains of this block copolymer. A significant decrease in the permeate temperature associated with the Joule–Thomson effect was observed for all TFCMs. The stepwise permeance drop was observed at a feed gas activity of p/po ≥ 1, clearly indicating that a penetrant transfer through the selective layer occurs only according to the conditions on the feed side of the membrane. The permeate side gas temperature has no influence on the state of the selective layer or penetrant diffusing through it. The most likely cause of the observed TFCM behaviour is capillary condensation of the penetrant in the swollen selective layer material, which can be provoked by the clustering of penetrant molecules.
Open AccessPermeance of Condensable Gases in Rubbery Polymer Membranes at High Pressure
The gas transport properties of thin film composite membranes (TFCMs) with selective layers of PolyActive™, polydimethylsiloxane (PDMS), and polyoctylmethylsiloxane (POMS) were investigated over a range of temperatures (10–34 °C; temperature increments of 2 °C) and pressures (1–65 bar abs; 38 pressure increments). The variation in the feed pressure of condensable gases CO2 and C2H6 enabled the observation of peaks of permeance in dependence on the feed pressure and temperature. For PDMS and POMS, the permeance peak was reproduced at the same feed gas activity as when the feed temperature was changed. PolyActive™ TFCM showed a more complex behaviour, most probably due to a higher CO2 affinity towards the poly(ethylene glycol) domains of this block copolymer. A significant decrease in the permeate temperature associated with the Joule–Thomson effect was observed for all TFCMs. The stepwise permeance drop was observed at a feed gas activity of p/po ≥ 1, clearly indicating that a penetrant transfer through the selective layer occurs only according to the conditions on the feed side of the membrane. The permeate side gas temperature has no influence on the state of the selective layer or penetrant diffusing through it. The most likely cause of the observed TFCM behaviour is capillary condensation of the penetrant in the swollen selective layer material, which can be provoked by the clustering of penetrant molecules.
- Open Access
- 20 February 2024
- Published by Wiley in Journal of Advanced Manufacturing and Processing
- Vol. 6 (2)
Numerical and experimental investigation of the unexpected thickening effect during PolyActive™ coating of TFC membranes
In this work, we used a previously described computational fluid dynamics (CFD) model of a roll‐to‐roll coating process for the fabrication of thin‐film composite membranes to predict the final coating thickness for PolyActive™, a commercially available multiblock copolymer utilized for CO2 removal membranes. We found a strong thickening effect that could not be explained by our previous model. We investigated the process experimentally. In addition, we conducted a variety of simulations with extensions of the initial CFD model. Based on our findings, we conclude that the Marangoni effect, that is, gradients of surface tension that induce secondary flow patterns in the meniscus region, is the most likely source of the observed thickening. We explain the simulation results in order to understand the physical mechanisms at play and to show how especially surface tension gradients that arise from the particular flow structure in the meniscus may explain the additional transfer of polymer solution to the membrane. Finally, we draw some conclusions on future research and give ideas on future improvements of the process. To our knowledge, Marangoni effects for the coating of PolyActive™ were not described so far in the literature, even though it is a well‐known polymer for gas separation membranes targeted at CO2 removal. Roll‐to‐roll coating is a well‐established coating method and often believed to be suitable for the scale‐up of membrane production, therefore we think that this work will help membrane researchers who are using similar coating devices to be cautious about possible complications in the process.
- 20 February 2024
- Published by Wiley in Journal of Advanced Manufacturing and Processing
- Vol. 6 (2)
Open AccessNumerical and experimental investigation of the unexpected thickening effect during PolyActive™ coating of TFC membranes
In this work, we used a previously described computational fluid dynamics (CFD) model of a roll‐to‐roll coating process for the fabrication of thin‐film composite membranes to predict the final coating thickness for PolyActive™, a commercially available multiblock copolymer utilized for CO2 removal membranes. We found a strong thickening effect that could not be explained by our previous model. We investigated the process experimentally. In addition, we conducted a variety of simulations with extensions of the initial CFD model. Based on our findings, we conclude that the Marangoni effect, that is, gradients of surface tension that induce secondary flow patterns in the meniscus region, is the most likely source of the observed thickening. We explain the simulation results in order to understand the physical mechanisms at play and to show how especially surface tension gradients that arise from the particular flow structure in the meniscus may explain the additional transfer of polymer solution to the membrane. Finally, we draw some conclusions on future research and give ideas on future improvements of the process. To our knowledge, Marangoni effects for the coating of PolyActive™ were not described so far in the literature, even though it is a well‐known polymer for gas separation membranes targeted at CO2 removal. Roll‐to‐roll coating is a well‐established coating method and often believed to be suitable for the scale‐up of membrane production, therefore we think that this work will help membrane researchers who are using similar coating devices to be cautious about possible complications in the process.
- Open Access
- 1 February 2024
- Published by Elsevier in Journal of Membrane Science
- Vol. 695
Temperature stable, polymeric thin-film composite membrane for hydrogen separation
- 1 February 2024
- Published by Elsevier in Journal of Membrane Science
- Vol. 695
Open AccessTemperature stable, polymeric thin-film composite membrane for hydrogen separation
- Open Access
Membrane-Assisted Methanol Synthesis Processes and the Required Permselectivity
Water-selective membrane reactors are proposed in the literature to improve methanol yield for a standalone reactor. However, the methanol productivity is not a precise metric to show the system improvement since, with this approach, we do not consider the amount of energy loss through the undesirable co-permeation of H2, which could otherwise remain on the reaction side at high pressure. In other words, the effectiveness of this new technology should be evaluated at a process flowsheet level to assess its advantages and disadvantages on the overall system performance and, more importantly, to identify the minimum required properties of the membrane. Therefore, an equation-based model for a membrane reactor, developed in Aspen Custom Modeler, was incorporated within the process flowsheet of the methanol plant to develop an integrated process framework to conduct the investigation. We determined the upper limit of the power-saving at 32% by exploring the favorable conditions wherein a conceptual water selective membrane reactor proves more effective. Using these suboptimal conditions, we realized that the minimum required H2O/H2 selectivity is 190 and 970 based on the exergy analysis and overall power requirement, respectively. According to our results, the permselectivity of membranes synthesized for this application in the literature, showing improvements in the one-pass conversion, is well below the minimum requirement when the overall methanol synthesis process flowsheet comes into consideration.
Open AccessMembrane-Assisted Methanol Synthesis Processes and the Required Permselectivity
Water-selective membrane reactors are proposed in the literature to improve methanol yield for a standalone reactor. However, the methanol productivity is not a precise metric to show the system improvement since, with this approach, we do not consider the amount of energy loss through the undesirable co-permeation of H2, which could otherwise remain on the reaction side at high pressure. In other words, the effectiveness of this new technology should be evaluated at a process flowsheet level to assess its advantages and disadvantages on the overall system performance and, more importantly, to identify the minimum required properties of the membrane. Therefore, an equation-based model for a membrane reactor, developed in Aspen Custom Modeler, was incorporated within the process flowsheet of the methanol plant to develop an integrated process framework to conduct the investigation. We determined the upper limit of the power-saving at 32% by exploring the favorable conditions wherein a conceptual water selective membrane reactor proves more effective. Using these suboptimal conditions, we realized that the minimum required H2O/H2 selectivity is 190 and 970 based on the exergy analysis and overall power requirement, respectively. According to our results, the permselectivity of membranes synthesized for this application in the literature, showing improvements in the one-pass conversion, is well below the minimum requirement when the overall methanol synthesis process flowsheet comes into consideration.
- Open Access
- 13 May 2021
- Published by Wiley in Chemie Ingenieur Technik
- Vol. 93 (8) , 1247-1256
Bewertung von Energieeffizienztechnologien mit der Methodik EDUAR&D an zwei Beispielen
- 13 May 2021
- Published by Wiley in Chemie Ingenieur Technik
- Vol. 93 (8) , 1247-1256
Open AccessBewertung von Energieeffizienztechnologien mit der Methodik EDUAR&D an zwei Beispielen
- Open Access
Zero-Discharge Process for Recycling of Tetrahydrofuran–Water Mixtures
The sustainable design of separation and polymer synthesis processes is of great importance. Therefore, an energy-efficient process for the purification of tetrahydrofuran (THF)–water (H2O) solvent mixtures from an upstream polymer synthesis process in pilot scale was developed with the aim to obtain high purity separation products. The advantages and limitations of a hybrid process in the pilot scale were studied utilizing an Aspen Plus Dynamics® simulation at different pressures to prove the feasibility and energy efficiency. For the rough separation of the two components, distillation was chosen as the first process step. In this way, a separation of a water stream of sufficient quality for further precipitations after polymer synthesis could be achieved. In order to overcome the limitations of the distillation process posed by the azeotropic point of the mixture, a vapor permeation is used, which takes advantage of the heat of evaporation already used in the distillation column. For the purpose of achieving the required low water contents, an adsorption column is installed downstream for final THF purification. This leads to a novel hybrid separation process that is energy efficient and thus allows also the use of the solvents again for upstream polymer synthesis achieving the high purity requirements in a closed-loop process.
Open AccessZero-Discharge Process for Recycling of Tetrahydrofuran–Water Mixtures
The sustainable design of separation and polymer synthesis processes is of great importance. Therefore, an energy-efficient process for the purification of tetrahydrofuran (THF)–water (H2O) solvent mixtures from an upstream polymer synthesis process in pilot scale was developed with the aim to obtain high purity separation products. The advantages and limitations of a hybrid process in the pilot scale were studied utilizing an Aspen Plus Dynamics® simulation at different pressures to prove the feasibility and energy efficiency. For the rough separation of the two components, distillation was chosen as the first process step. In this way, a separation of a water stream of sufficient quality for further precipitations after polymer synthesis could be achieved. In order to overcome the limitations of the distillation process posed by the azeotropic point of the mixture, a vapor permeation is used, which takes advantage of the heat of evaporation already used in the distillation column. For the purpose of achieving the required low water contents, an adsorption column is installed downstream for final THF purification. This leads to a novel hybrid separation process that is energy efficient and thus allows also the use of the solvents again for upstream polymer synthesis achieving the high purity requirements in a closed-loop process.
- 1 March 2003
- Published by Wiley in Annals of the New York Academy of Sciences
- Vol. 984 (1) , 306-317
Natural Gas Cleanup by Means of Membranes
Abstract: This paper deals with the use of membranes for hydrocarbon dewpointing and dehydration of natural gas. Based on experience gained from membrane applications in separating organic vapors from off‐gas and process streams, as well as the dehydration of compressed air, membranes have been developed and tested for use in high pressure applications. Membranes and membrane modules have been modified to withstand the high operating pressure. Calculation programs were developed to understand the separation performance and to provide the necessary information for optimizing membrane design. A real challenge was the introduction of the vacuum mode dehydration operation in order to achieve the highest possible dewpoint reduction with minimum methane loss.
- 1 March 2003
- Published by Wiley in Annals of the New York Academy of Sciences
- Vol. 984 (1) , 306-317
Natural Gas Cleanup by Means of Membranes
Abstract: This paper deals with the use of membranes for hydrocarbon dewpointing and dehydration of natural gas. Based on experience gained from membrane applications in separating organic vapors from off‐gas and process streams, as well as the dehydration of compressed air, membranes have been developed and tested for use in high pressure applications. Membranes and membrane modules have been modified to withstand the high operating pressure. Calculation programs were developed to understand the separation performance and to provide the necessary information for optimizing membrane design. A real challenge was the introduction of the vacuum mode dehydration operation in order to achieve the highest possible dewpoint reduction with minimum methane loss.