Sharee Harris
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sharee Harris has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
A. J. Swift
Lawrence Livermore National Laboratory 1 , P.O. Box 808, Livermore, California 94551
1 shared publication- A. M. Parkes
AWE Nuclear Security Technologies 2 , Aldermaston, Reading RG7 4PR
1 shared publication - Alfred T. Sidambe
University of Sheffield
1 shared publication Andrew J. Pascall
1 shared publication- Andrew J. Pascall
Lawrence Livermore National Laboratory, 7000 East Avenue, Livermore, California 94550, USA
1 shared publication - Ashley M. Hastings
Nuclear and Chemical Sciences Division, Lawrence Livermore National Laboratory, Livermore, CA 94550, USA
1 shared publication
Latest Publications
- Open Access
- 7 June 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (12) , 6431
Investigation of In Situ and Ex Situ Passivation of Pyrophoric Uranium–Niobium Alloy Powder
This work evaluates the effectiveness of in situ and ex situ passivation methods for mitigating the pyrophoricity of uranium–6 wt.% niobium spherical powders produced via the hydride–dehydride process coupled with plasma spheroidization. Oxide layer thickness was characterized using STEM/EDX, and pyrophoricity was assessed by a UN-recommended test method, which involves directly dropping the powders in the air. In situ passivation, performed by introducing flowing oxygen during spheroidization, produced oxide layers ranging from tens to hundreds of nanometers but resulted in inconsistent pyrophoricity mitigation at lower oxygen flow rates. Ex situ passivation, achieved by slow oxygen exposure over several months, formed uniform oxide layers of approximately 20 nm and consistently mitigated pyrophoricity. Despite requiring higher bulk oxygen content, in situ passivation enables faster processing and control of oxygen, while ex situ passivation achieves superior oxide uniformity with lower oxygen incorporation. These findings highlight the trade-offs between passivation methods and provide a foundation for improving the safety and scalability of reactive metal powder production.
- 7 June 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (12) , 6431
Open AccessInvestigation of In Situ and Ex Situ Passivation of Pyrophoric Uranium–Niobium Alloy Powder
This work evaluates the effectiveness of in situ and ex situ passivation methods for mitigating the pyrophoricity of uranium–6 wt.% niobium spherical powders produced via the hydride–dehydride process coupled with plasma spheroidization. Oxide layer thickness was characterized using STEM/EDX, and pyrophoricity was assessed by a UN-recommended test method, which involves directly dropping the powders in the air. In situ passivation, performed by introducing flowing oxygen during spheroidization, produced oxide layers ranging from tens to hundreds of nanometers but resulted in inconsistent pyrophoricity mitigation at lower oxygen flow rates. Ex situ passivation, achieved by slow oxygen exposure over several months, formed uniform oxide layers of approximately 20 nm and consistently mitigated pyrophoricity. Despite requiring higher bulk oxygen content, in situ passivation enables faster processing and control of oxygen, while ex situ passivation achieves superior oxide uniformity with lower oxygen incorporation. These findings highlight the trade-offs between passivation methods and provide a foundation for improving the safety and scalability of reactive metal powder production.
- 30 April 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (3)
Small-scale production of bespoke accelerated aging plutonium alloy
This study demonstrates the 100 g scale manufacture of a plutonium alloy that ages at an accelerated rate. The resulting alloy ages six times faster than typical weapons-grade plutonium due to the addition of 238Pu. As a major innovation, the process involved using a partial direct oxide reduction technique. This method was achieved by developing a new, complex geometry stirrer using additive manufacturing to reduce the 238Pu oxide and efficiently incorporate it into weapons-grade plutonium metal. The material was then purified by molten salt extraction and electrorefining before being alloyed with gallium. The alloy was then cold-rolled and annealed in a homogenization heat treatment. The resulting disk was characterized by metallography and differential scanning calorimetry, and the impurity content was determined using analytical chemistry techniques. The results show that a homogeneous delta phase plutonium alloy was achieved with expected microstructure and minimal impurities. This study was also successful in changing the plutonium isotopic composition by incorporating additional 238Pu to accelerate the effects of radiation damage. This enables researchers to study long-term aging phenomena in a reduced time frame, thus avoiding the need for large-scale material production and circumventing the limitations of using naturally aged, archived plutonium.
- 30 April 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (3)
Small-scale production of bespoke accelerated aging plutonium alloy
This study demonstrates the 100 g scale manufacture of a plutonium alloy that ages at an accelerated rate. The resulting alloy ages six times faster than typical weapons-grade plutonium due to the addition of 238Pu. As a major innovation, the process involved using a partial direct oxide reduction technique. This method was achieved by developing a new, complex geometry stirrer using additive manufacturing to reduce the 238Pu oxide and efficiently incorporate it into weapons-grade plutonium metal. The material was then purified by molten salt extraction and electrorefining before being alloyed with gallium. The alloy was then cold-rolled and annealed in a homogenization heat treatment. The resulting disk was characterized by metallography and differential scanning calorimetry, and the impurity content was determined using analytical chemistry techniques. The results show that a homogeneous delta phase plutonium alloy was achieved with expected microstructure and minimal impurities. This study was also successful in changing the plutonium isotopic composition by incorporating additional 238Pu to accelerate the effects of radiation damage. This enables researchers to study long-term aging phenomena in a reduced time frame, thus avoiding the need for large-scale material production and circumventing the limitations of using naturally aged, archived plutonium.
- Open Access
- 1 April 2024
- Published by Royal Society of Chemistry (RSC) in Dalton Transactions
- Vol. 53 (17) , 7376-7383
Preparation of monodisperse cerium oxide particle suspensions from a tetravalent precursor
Stable, monodisperse sub-micron cerium particle suspensions were synthesized from a CeIV precursor by homogeneous precipitation with hexamethylenetetramine and ammonium hydroxide.
- 1 April 2024
- Published by Royal Society of Chemistry (RSC) in Dalton Transactions
- Vol. 53 (17) , 7376-7383
Open AccessPreparation of monodisperse cerium oxide particle suspensions from a tetravalent precursor
Stable, monodisperse sub-micron cerium particle suspensions were synthesized from a CeIV precursor by homogeneous precipitation with hexamethylenetetramine and ammonium hydroxide.
- 5 February 2024
- Published by Elsevier in Materials Letters
- Vol. 361
Electrophoretic deposition for improved trace element homogeneity in silica reference materials
- 5 February 2024
- Published by Elsevier in Materials Letters
- Vol. 361
Electrophoretic deposition for improved trace element homogeneity in silica reference materials