Jie Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jie Chen has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
Yong Wang
6 shared publicationsLing Bai
4 shared publications- Ling Zhou
National Research Center of Pumps, Jiangsu University, Zhenjiang, China
4 shared publications Ming Li
Research Center of Fluid Machinery Engineering and Technology, Jiangsu University, Zhenjiang, China
4 shared publicationsXiaolin Wang
Chongqing Vocational Institute of Engineering, Chongqing, China
4 shared publications- Biao Huang
School of Mechanical Engineering, Beijing Institute of Technology 1 , Beijing 100081
3 shared publications
Latest Publications
- 1 September 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (9)
Quantifying uncertainty in propeller cavitation flow using an implicit large eddy simulation-based verification and validation framework
To address the adverse effects of unsteady vortices and cavitation on propeller efficiency and navigational safety at high operating speeds, this study performed numerical simulations of cavitating flow around the marine propeller PC456 using an implicit large eddy simulation (LES) approach coupled with the boundary data immersion method and a local mesh refinement strategy, with five systematically refined meshes. The flow-field characteristics were systematically analyzed. Sheet cavitation developed along the blade leading edges, while tip-vortex cavitation originated near the blade tips and evolved into helical structures in the near wake. Their interaction generated strong local fluctuations in pressure and velocity fields. The wake-vortex system was primarily composed of tip vortices and a hub vortex, with tip vortices dominating the wake dynamics. A verification and validation framework based on implicit LES was established by combining the five-equation method with the safety factor method to quantitatively evaluate numerical and modeling uncertainties in key flow parameters. To address the limitations of the conventional five-equation method, specifically its sensitivity to initial guesses and susceptibility to convergence to local optima in strongly nonlinear cavitating flows, an improved optimization strategy incorporating multiple randomized initial guesses and penalty-term constraints was introduced and applied to the cavitating flow field. The results showed close agreement with experimental measurements in terms of thrust and torque coefficients, while velocity and pressure uncertainties remained within reasonable bounds. The proposed framework provides a quantitative methodology for evaluating cavitating-flow predictions and guiding future engineering applications.
- 1 September 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (9)
Quantifying uncertainty in propeller cavitation flow using an implicit large eddy simulation-based verification and validation framework
To address the adverse effects of unsteady vortices and cavitation on propeller efficiency and navigational safety at high operating speeds, this study performed numerical simulations of cavitating flow around the marine propeller PC456 using an implicit large eddy simulation (LES) approach coupled with the boundary data immersion method and a local mesh refinement strategy, with five systematically refined meshes. The flow-field characteristics were systematically analyzed. Sheet cavitation developed along the blade leading edges, while tip-vortex cavitation originated near the blade tips and evolved into helical structures in the near wake. Their interaction generated strong local fluctuations in pressure and velocity fields. The wake-vortex system was primarily composed of tip vortices and a hub vortex, with tip vortices dominating the wake dynamics. A verification and validation framework based on implicit LES was established by combining the five-equation method with the safety factor method to quantitatively evaluate numerical and modeling uncertainties in key flow parameters. To address the limitations of the conventional five-equation method, specifically its sensitivity to initial guesses and susceptibility to convergence to local optima in strongly nonlinear cavitating flows, an improved optimization strategy incorporating multiple randomized initial guesses and penalty-term constraints was introduced and applied to the cavitating flow field. The results showed close agreement with experimental measurements in terms of thrust and torque coefficients, while velocity and pressure uncertainties remained within reasonable bounds. The proposed framework provides a quantitative methodology for evaluating cavitating-flow predictions and guiding future engineering applications.
- 1 August 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (8)
Boundary-layer separation and vortex evolution in a centrifugal pump: Large-eddy simulation and particle image velocimetry
To elucidate the evolution of unsteady internal flow structures in a low-specific-speed centrifugal pump under different flow rate conditions, large-eddy simulation (LES) was employed to systematically investigate the flow within the impeller. Particle image velocimetry) measurements were conducted to validate the reliability of the numerical method in predicting the planar velocity field and the dominant vortical structures. On this basis, particular attention was paid to boundary-layer separation on the blade surfaces and its coupling with the vortical structures within the blade passages. The results show that, under the high-flow rate condition, boundary-layer separation on the blade pressure side is primarily governed by the adverse static-pressure gradient. The maximum separation length exhibits a phase lag of approximately 37° relative to the peak adverse pressure gradient. Localized vortical structures are also evident near the blade suction side, where they enhance local momentum exchange and, to some extent, constrain the development of boundary-layer separation. As the flow rate decreases, the low-velocity and separated-flow regions on the blade suction side progressively expand, further promoting the formation of large-scale vortical structures within the blade passages. At 0.6Qd, the suction-side separation region increases markedly, and the vortex volume identified using a fixed Liutex threshold is approximately 69% greater than that at 1.3Qd. These large-scale separated-flow structures substantially reduce the effective flow area at the entrances of several blade passages, thereby leading to the formation of stalled passages. Furthermore, the three-dimensional LES results reveal that the large-scale vortical structures exhibit an alternating circumferential distribution in the six-bladed impeller and show no evident rotational propagation within the present statistical sampling period. Through hydraulic blockage and momentum redistribution within the blade passages, the large-scale separation vortices on the blade suction side delay or suppress, to some extent, the development of boundary-layer separation on the pressure side.
- 1 August 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (8)
Boundary-layer separation and vortex evolution in a centrifugal pump: Large-eddy simulation and particle image velocimetry
To elucidate the evolution of unsteady internal flow structures in a low-specific-speed centrifugal pump under different flow rate conditions, large-eddy simulation (LES) was employed to systematically investigate the flow within the impeller. Particle image velocimetry) measurements were conducted to validate the reliability of the numerical method in predicting the planar velocity field and the dominant vortical structures. On this basis, particular attention was paid to boundary-layer separation on the blade surfaces and its coupling with the vortical structures within the blade passages. The results show that, under the high-flow rate condition, boundary-layer separation on the blade pressure side is primarily governed by the adverse static-pressure gradient. The maximum separation length exhibits a phase lag of approximately 37° relative to the peak adverse pressure gradient. Localized vortical structures are also evident near the blade suction side, where they enhance local momentum exchange and, to some extent, constrain the development of boundary-layer separation. As the flow rate decreases, the low-velocity and separated-flow regions on the blade suction side progressively expand, further promoting the formation of large-scale vortical structures within the blade passages. At 0.6Qd, the suction-side separation region increases markedly, and the vortex volume identified using a fixed Liutex threshold is approximately 69% greater than that at 1.3Qd. These large-scale separated-flow structures substantially reduce the effective flow area at the entrances of several blade passages, thereby leading to the formation of stalled passages. Furthermore, the three-dimensional LES results reveal that the large-scale vortical structures exhibit an alternating circumferential distribution in the six-bladed impeller and show no evident rotational propagation within the present statistical sampling period. Through hydraulic blockage and momentum redistribution within the blade passages, the large-scale separation vortices on the blade suction side delay or suppress, to some extent, the development of boundary-layer separation on the pressure side.
- 1 November 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (11)
Numerical investigation on unsteady tip leakage cavitating flow around a pitching flat plate hydrofoil
Tip leakage cavitating flow under a dynamic boundary remains a critical challenge in axial hydraulic machinery; research characterizing such cavitating flow with acceptable accuracy is currently limited. In this study, a flat plate hydrofoil undergoing sinusoidal pitching motion around the mid-chord point is employed to simulate tip leakage cavitating flow under dynamic boundaries. The shear stress transport k-ω model and the Zwart–Gerber–Belamri model are applied to investigate the cavitation patterns and vortex structures within the tip clearance under pitching motion. The results indicate that the tip leakage cavitating flow involves the tip leakage vortex (TLV), the tip separation vortex, and the induced vortex, with the TLV being the dominant vortex structure. The TLV-induced tip leakage vortex cavitation (TLVC) is the only cavitation pattern within the tip clearance. The TLV and TLVC exhibit significant periodicity during the pitching process. During the upstroke phase, the TLVC intensity gradually decreases, the streamwise vorticity near the TLVC gradually increases, and the velocity circulation initially decreases and then increases. However, during the downstroke phase, the changes in these features are opposite to those in the upstroke phase. In addition, at the same angle of attack for upstroke and downstroke phases, the TLV and TLVC intensity are greater in the downstroke phase. Moreover, a wandering cavity appears in the TLVC during the upstroke phase, while the TLVC has more integral shape during the downstroke phase.
- 1 November 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (11)
Numerical investigation on unsteady tip leakage cavitating flow around a pitching flat plate hydrofoil
Tip leakage cavitating flow under a dynamic boundary remains a critical challenge in axial hydraulic machinery; research characterizing such cavitating flow with acceptable accuracy is currently limited. In this study, a flat plate hydrofoil undergoing sinusoidal pitching motion around the mid-chord point is employed to simulate tip leakage cavitating flow under dynamic boundaries. The shear stress transport k-ω model and the Zwart–Gerber–Belamri model are applied to investigate the cavitation patterns and vortex structures within the tip clearance under pitching motion. The results indicate that the tip leakage cavitating flow involves the tip leakage vortex (TLV), the tip separation vortex, and the induced vortex, with the TLV being the dominant vortex structure. The TLV-induced tip leakage vortex cavitation (TLVC) is the only cavitation pattern within the tip clearance. The TLV and TLVC exhibit significant periodicity during the pitching process. During the upstroke phase, the TLVC intensity gradually decreases, the streamwise vorticity near the TLVC gradually increases, and the velocity circulation initially decreases and then increases. However, during the downstroke phase, the changes in these features are opposite to those in the upstroke phase. In addition, at the same angle of attack for upstroke and downstroke phases, the TLV and TLVC intensity are greater in the downstroke phase. Moreover, a wandering cavity appears in the TLVC during the upstroke phase, while the TLVC has more integral shape during the downstroke phase.
- 1 June 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (6)
Vortex structure analysis in the podded thruster using boundary data immersion method with verification and validation
This study investigates the vortex dynamics around the podded thruster through implicit large eddy simulation (ILES) coupled with the boundary data immersion method (BDIM). Numerical simulations are conducted using a Fortran-based solver, with verification and validation procedures demonstrating predictive reliability through minimal total error, and the validation error (|E|) remains below the validation uncertainty threshold (Uv). Meanwhile, three distinct vortex structures are identified: (1) the horseshoe vortex at the strut-pod junction, (2) the hairpin vortex at the top of the strut, and (3) the wake vortex system downstream of the propeller. The horseshoe vortex originates from boundary layer separation induced by an adverse pressure gradient. This structure undergoes stretching under the influence of rotational dominance. The hairpin vortex, evolving due to shear layer instability, progresses from vortex ring formation to self-induced uplift and multi-scale interactions, ultimately dissipating through turbulent bursting. The wake vortex system exhibits strong instability and turbulent breakdown, leading to rapid downstream deformation and energy dissipation.
- 1 June 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (6)
Vortex structure analysis in the podded thruster using boundary data immersion method with verification and validation
This study investigates the vortex dynamics around the podded thruster through implicit large eddy simulation (ILES) coupled with the boundary data immersion method (BDIM). Numerical simulations are conducted using a Fortran-based solver, with verification and validation procedures demonstrating predictive reliability through minimal total error, and the validation error (|E|) remains below the validation uncertainty threshold (Uv). Meanwhile, three distinct vortex structures are identified: (1) the horseshoe vortex at the strut-pod junction, (2) the hairpin vortex at the top of the strut, and (3) the wake vortex system downstream of the propeller. The horseshoe vortex originates from boundary layer separation induced by an adverse pressure gradient. This structure undergoes stretching under the influence of rotational dominance. The hairpin vortex, evolving due to shear layer instability, progresses from vortex ring formation to self-induced uplift and multi-scale interactions, ultimately dissipating through turbulent bursting. The wake vortex system exhibits strong instability and turbulent breakdown, leading to rapid downstream deformation and energy dissipation.
- 8 March 2025
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 47 (4) , 1-10
Investigation of the effect of temperature on the characteristics of differential pressure control valve
- 8 March 2025
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 47 (4) , 1-10
Investigation of the effect of temperature on the characteristics of differential pressure control valve
- 1 March 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (3)
Numerical and experimental study of viscosity effects on an electric submersible pump
This study systematically investigates the performance and internal flow field characteristics of the 387 series three-stage electric submersible pump under varying viscosities. By integrating experimental data with numerical simulations, the research focuses on analyzing the effects of medium viscosity on the pump's hydraulic performance, efficiency, power, and energy losses. Additionally, the turbulence suppression effect under high-viscosity conditions is thoroughly examined through numerical simulations. The results show that as viscosity increases, both the pump head and efficiency decline significantly, while total entropy generation rises substantially. Specifically, the pump efficiency drops from 48.32% to 3.2% as viscosity increases from 20 to 696 mPa·s, with a notable rise in total entropy production. The proportion of entropy generation due to direct dissipation and wall effects gradually increases under high-viscosity conditions. Vortex structure analysis reveals that under high-viscosity conditions, vortex intensity weakens and fluid rotation decreases, while wall shear effects and viscous dissipation become significantly stronger, emerging as the primary sources of energy loss. The distribution of wall entropy generation is concentrated at the inlet and outlet of the impeller blades, the leading edge of the guide vanes, and near the inlet and outlet of the impeller and guide vane backplates, highlighting the dominant role of viscous dissipation under high-viscosity conditions. These findings provide valuable theoretical and practical insights for optimizing the performance and enhancing the efficiency of electric submersible pumps in high-viscosity.
- 1 March 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (3)
Numerical and experimental study of viscosity effects on an electric submersible pump
This study systematically investigates the performance and internal flow field characteristics of the 387 series three-stage electric submersible pump under varying viscosities. By integrating experimental data with numerical simulations, the research focuses on analyzing the effects of medium viscosity on the pump's hydraulic performance, efficiency, power, and energy losses. Additionally, the turbulence suppression effect under high-viscosity conditions is thoroughly examined through numerical simulations. The results show that as viscosity increases, both the pump head and efficiency decline significantly, while total entropy generation rises substantially. Specifically, the pump efficiency drops from 48.32% to 3.2% as viscosity increases from 20 to 696 mPa·s, with a notable rise in total entropy production. The proportion of entropy generation due to direct dissipation and wall effects gradually increases under high-viscosity conditions. Vortex structure analysis reveals that under high-viscosity conditions, vortex intensity weakens and fluid rotation decreases, while wall shear effects and viscous dissipation become significantly stronger, emerging as the primary sources of energy loss. The distribution of wall entropy generation is concentrated at the inlet and outlet of the impeller blades, the leading edge of the guide vanes, and near the inlet and outlet of the impeller and guide vane backplates, highlighting the dominant role of viscous dissipation under high-viscosity conditions. These findings provide valuable theoretical and practical insights for optimizing the performance and enhancing the efficiency of electric submersible pumps in high-viscosity.
- 1 February 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (2)
Computational fluid dynamics−discrete element method simulation and experimental study of particle transport mechanism in a centrifugal pump
Pumps are one of the most important equipment in deep-sea mining system, which transport particles continuously from the seafloor. In this paper, the computational fluid dynamics−discrete element method (CFD−DEM) numerical simulation was used to analyze the effect of particle volume fraction (PVF) on the particle transport mechanism in the pump. The reliability of the CFD−DEM numerical simulation was verified by high-speed photography experiments. The results show that the particles mainly move along the blade pressure surface (BPS) in the impeller, and the particles can suppress the formation of low-velocity vortices on the BPS. The translational velocity of the particles is less affected by the PVF, but has a significant effect on the rotational velocity. The flow pattern of particles inside the volute is categorized into wake flow, cutting flow, and near wall flow. With the increase in PVF, the particles are subjected to pressure gradient force, drag force, and virtual mass force in the pump gradually increase, but the lift force on the particles gradually decreases. The tangential force and normal force between particles increased with increasing PVF, and the increase in PVF from 2% to 10% was 462.55% and 148.17%, respectively. The collision frequency per unit time of particles with volute is the largest, but the collision frequency per unit time and per unit area is the largest for impeller. The most significant impact work of particles with volute and particles with blades is 371.08% and 505.66% when PVF increases from 2% to 10%. This study can provide theoretical guidance for the optimal design of solid−liquid two-phase pumps.
- 1 February 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (2)
Computational fluid dynamics−discrete element method simulation and experimental study of particle transport mechanism in a centrifugal pump
Pumps are one of the most important equipment in deep-sea mining system, which transport particles continuously from the seafloor. In this paper, the computational fluid dynamics−discrete element method (CFD−DEM) numerical simulation was used to analyze the effect of particle volume fraction (PVF) on the particle transport mechanism in the pump. The reliability of the CFD−DEM numerical simulation was verified by high-speed photography experiments. The results show that the particles mainly move along the blade pressure surface (BPS) in the impeller, and the particles can suppress the formation of low-velocity vortices on the BPS. The translational velocity of the particles is less affected by the PVF, but has a significant effect on the rotational velocity. The flow pattern of particles inside the volute is categorized into wake flow, cutting flow, and near wall flow. With the increase in PVF, the particles are subjected to pressure gradient force, drag force, and virtual mass force in the pump gradually increase, but the lift force on the particles gradually decreases. The tangential force and normal force between particles increased with increasing PVF, and the increase in PVF from 2% to 10% was 462.55% and 148.17%, respectively. The collision frequency per unit time of particles with volute is the largest, but the collision frequency per unit time and per unit area is the largest for impeller. The most significant impact work of particles with volute and particles with blades is 371.08% and 505.66% when PVF increases from 2% to 10%. This study can provide theoretical guidance for the optimal design of solid−liquid two-phase pumps.
- 1 February 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (2)
Vortex dynamics analysis of an energy loss mechanism in a centrifugal pump impeller
Centrifugal pumps play a vital role in industrial production, particularly for the transportation of viscous liquids, where they often incur significant energy losses. This study investigates the energy loss mechanisms in centrifugal pump impellers, focusing on the dynamics of vortices under varying viscosities and rotational speeds through numerical simulation. The proportion and distribution of entropy production under different viscosities and rotational speeds are discussed, and the influence of different terms of the vorticity transport equation on vorticity changes is analyzed. The results show that turbulent dissipation entropy production is the main entropy production at low viscosities. As the viscosity increases, the proportion of wall entropy production rises and becomes the main source of energy loss in the pump. Under high rotating speed condition, the Coriolis force source term is the main reason for vorticity changes. As the viscosity increases, the Coriolis force source term decreases sharply, and the relative vortex stretching term also decreases. Meanwhile, the viscosity diffusion term increases and becomes the main reason for the reduction of unstable flow in the impeller of a centrifugal pump for high-viscosity fluid media. This study combines the vorticity transport equation with entropy production analysis to analyze the energy conversion process and loss generation mechanism in a centrifugal pump, and deeply explore the relationship between the vorticity field and energy loss in the impeller. It has theoretical and practical significance for improving the efficiency of centrifugal pumps in transporting viscous fluids and providing support for related designs.
- 1 February 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (2)
Vortex dynamics analysis of an energy loss mechanism in a centrifugal pump impeller
Centrifugal pumps play a vital role in industrial production, particularly for the transportation of viscous liquids, where they often incur significant energy losses. This study investigates the energy loss mechanisms in centrifugal pump impellers, focusing on the dynamics of vortices under varying viscosities and rotational speeds through numerical simulation. The proportion and distribution of entropy production under different viscosities and rotational speeds are discussed, and the influence of different terms of the vorticity transport equation on vorticity changes is analyzed. The results show that turbulent dissipation entropy production is the main entropy production at low viscosities. As the viscosity increases, the proportion of wall entropy production rises and becomes the main source of energy loss in the pump. Under high rotating speed condition, the Coriolis force source term is the main reason for vorticity changes. As the viscosity increases, the Coriolis force source term decreases sharply, and the relative vortex stretching term also decreases. Meanwhile, the viscosity diffusion term increases and becomes the main reason for the reduction of unstable flow in the impeller of a centrifugal pump for high-viscosity fluid media. This study combines the vorticity transport equation with entropy production analysis to analyze the energy conversion process and loss generation mechanism in a centrifugal pump, and deeply explore the relationship between the vorticity field and energy loss in the impeller. It has theoretical and practical significance for improving the efficiency of centrifugal pumps in transporting viscous fluids and providing support for related designs.
- Open Access
- 12 December 2024
- Published by Elsevier in Computational Particle Mechanics
- Vol. 12 (2) , 1291-1307
Investigation of typical cavitation flow mode and flow field characteristics in a centrifugal pump
- 12 December 2024
- Published by Elsevier in Computational Particle Mechanics
- Vol. 12 (2) , 1291-1307
Open AccessInvestigation of typical cavitation flow mode and flow field characteristics in a centrifugal pump
- 1 December 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (12)
Combined experimental and computational investigation of the influence of micro vortex generator on incipient cavitation mode
The objective of this paper is to investigate the effect of a passive control method on the incipient cavitation mode around a hydrofoil. Two micro vortex generators (mVGs) with different positions are installed on the leading edge (LE) of the NACA (National Advisory Committee for Aeronautics) 66 hydrofoil. The mVG-1 has the same structural parameters as the mVG-2, but it is closer to the LE of hydrofoil. A high-speed camera is used to record the transient behavior of the cavitating flow. The large eddy simulation combined with a mass transport model is applied to analyze the influence mechanism of mVG on the incipient cavitation mode. The results show that the three typical incipient cavitation modes are observed on the baseline hydrofoil, i.e., spot cavity, patch cavity, and finger cavity. The mVG induces the generation of vortex shaped like thin strips of fingers at its trailing edge, called the fingerlike vortex cavitation. The neighboring fingerlike vortices constitute a pair of counter-rotating vortices with equal sizes and opposite directions. It influences the near-wall flow state upstream and downstream of mVG and, thus, the incipient cavitation structure. For the mVG-1 hydrofoil, the fingerlike vortex cavitation is a unique form of the incipient cavitation mode, making the cavitation onset position fixed at the mVG tail. For the mVG-2 hydrofoil, the mVG has a significant effect on the incipient cavitation structure at small attack angles, changing both the incipient cavitation mode and position.
- 1 December 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (12)
Combined experimental and computational investigation of the influence of micro vortex generator on incipient cavitation mode
The objective of this paper is to investigate the effect of a passive control method on the incipient cavitation mode around a hydrofoil. Two micro vortex generators (mVGs) with different positions are installed on the leading edge (LE) of the NACA (National Advisory Committee for Aeronautics) 66 hydrofoil. The mVG-1 has the same structural parameters as the mVG-2, but it is closer to the LE of hydrofoil. A high-speed camera is used to record the transient behavior of the cavitating flow. The large eddy simulation combined with a mass transport model is applied to analyze the influence mechanism of mVG on the incipient cavitation mode. The results show that the three typical incipient cavitation modes are observed on the baseline hydrofoil, i.e., spot cavity, patch cavity, and finger cavity. The mVG induces the generation of vortex shaped like thin strips of fingers at its trailing edge, called the fingerlike vortex cavitation. The neighboring fingerlike vortices constitute a pair of counter-rotating vortices with equal sizes and opposite directions. It influences the near-wall flow state upstream and downstream of mVG and, thus, the incipient cavitation structure. For the mVG-1 hydrofoil, the fingerlike vortex cavitation is a unique form of the incipient cavitation mode, making the cavitation onset position fixed at the mVG tail. For the mVG-2 hydrofoil, the mVG has a significant effect on the incipient cavitation structure at small attack angles, changing both the incipient cavitation mode and position.