Runcong Lv
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Runcong Lv has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Qing-Yi Guo
Department of Electrical Engineering, State Key Laboratory of Terahertz and Millimeter Waves, City University of Hong Kong, Hong Kong, China
7 shared publications - Chenfeng Yang
Department of Electrical Engineering, State Key Laboratory of Terahertz and Millimeter Waves, City University of Hong Kong, Hong Kong, China
2 shared publications - Hang Wong
City University of Hong Kong
2 shared publications - Guoxiang Shu
State Key Laboratory of Radio Frequency Heterogeneous Integration and the College of Electronics and Information Engineering, Shenzhen University, Shenzhen, China
1 shared publication Jintao Liu
Shenzhen University
1 shared publicationMingxuan Liang
State Key Laboratory of Radio Frequency Heterogeneous Integration, Shenzhen University, Shenzhen, China
1 shared publication
Latest Publications
- 16 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 74 (7) , 6079-6090
A Compact, High-Gain Substrate-Integrated H-Plane Fabry--Pérot Cavity Fed Long-Slot Antenna With Loaded E-Dipole for Millimeter-Wave Application
In this paper, a compact, high-gain substrate integrated H-plane Fabry–Pérot cavity (FPC) fed long-slot antenna with loaded dipole array for millimeter-wave (mmW) applications has been proposed. The proposed design consists of only two substrates, with a simple structure and low manufacturing cost. This paper proposes the architecture of H-plane FPC, which is used to excite a long-slot to achieve high-gain radiation. Designed air-based partially reflective surface (PRS) and via-based ground (VBG) contributes to integrate the proposed H-plane FPC into a single-layer substrate. This makes the proposed antenna yields a superior advantage of compact sized in terms of occupied area and profile when compared to recently reported antenna arrays with similar gain levels. In addition, the middle of the air-based PRS is designed in a V-shape, and the remaining area is designed with uneven thickness distribution, which improves impedance matching and increases antenna’s gain. The VBG is designed in a parabolic shape to excite multiple modes, which helps to increase the gain bandwidth. Furthermore, loaded E-dipole and upper cavity were designed to further enhance the gain of the long-slot. For demonstration, an antenna protype based on the design above is designed, manufactured, and measured. The measured results indicate that the working bandwidth of the antenna is 11.6 %. It produces a peak gain of 15.61 dBi and stable in band radiation patterns. Compared to antennas of the same type, the proposed one has superior advantages in size, gain, bandwidth, and simplicity.
- 16 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 74 (7) , 6079-6090
A Compact, High-Gain Substrate-Integrated H-Plane Fabry--Pérot Cavity Fed Long-Slot Antenna With Loaded E-Dipole for Millimeter-Wave Application
In this paper, a compact, high-gain substrate integrated H-plane Fabry–Pérot cavity (FPC) fed long-slot antenna with loaded dipole array for millimeter-wave (mmW) applications has been proposed. The proposed design consists of only two substrates, with a simple structure and low manufacturing cost. This paper proposes the architecture of H-plane FPC, which is used to excite a long-slot to achieve high-gain radiation. Designed air-based partially reflective surface (PRS) and via-based ground (VBG) contributes to integrate the proposed H-plane FPC into a single-layer substrate. This makes the proposed antenna yields a superior advantage of compact sized in terms of occupied area and profile when compared to recently reported antenna arrays with similar gain levels. In addition, the middle of the air-based PRS is designed in a V-shape, and the remaining area is designed with uneven thickness distribution, which improves impedance matching and increases antenna’s gain. The VBG is designed in a parabolic shape to excite multiple modes, which helps to increase the gain bandwidth. Furthermore, loaded E-dipole and upper cavity were designed to further enhance the gain of the long-slot. For demonstration, an antenna protype based on the design above is designed, manufactured, and measured. The measured results indicate that the working bandwidth of the antenna is 11.6 %. It produces a peak gain of 15.61 dBi and stable in band radiation patterns. Compared to antennas of the same type, the proposed one has superior advantages in size, gain, bandwidth, and simplicity.
- 15 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 73 (11) , 8707-8717
A Wideband, Miniaturized Millimeter-Wave Fabry–Pérot Cavity Antenna Without Independent Partially Reflective Surface Enabled by Dielectric-Filled-Shape-Cavity
In this paper, a compact Fabry–Pérot Cavity (FPC) architecture with simple structure is introduced for millimeter-wave (mmW) application. This is the first attempt to apply a dielectric-filled-shape-cavity (DFSC) as the cavity of an FPC antenna. By utilizing discontinuity of permittivity between the dielectric and air, intrinsic partial reflection effect can be formed without extra partially reflective surface (PRS), which is commonly required by a conventional FPC. At the same time, due to relative high dielectric of the DFSC, antenna size can be significantly miniaturized. Furthermore, we modified the structure of DFSC to form a reverse-stepped shape, contributing to bandwidth and gain enhancement of the FPC antenna. The proposed antenna consists of only two components, a feeding antenna and the proposed DFSC. The size of the antenna is 4λ0*4λ0, which is much smaller when compared with recently reported FPC type of antennas. For demonstration, the antenna was designed, manufactured, and measured. The measured results show that the working bandwidth of the antenna is 15.9 %. It yields a peak gain of 18.3 dBi and in-band radiation pattern is stable. The proposed antenna has superior advantages in terms of size, bandwidth, and simplicity.
- 15 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 73 (11) , 8707-8717
A Wideband, Miniaturized Millimeter-Wave Fabry–Pérot Cavity Antenna Without Independent Partially Reflective Surface Enabled by Dielectric-Filled-Shape-Cavity
In this paper, a compact Fabry–Pérot Cavity (FPC) architecture with simple structure is introduced for millimeter-wave (mmW) application. This is the first attempt to apply a dielectric-filled-shape-cavity (DFSC) as the cavity of an FPC antenna. By utilizing discontinuity of permittivity between the dielectric and air, intrinsic partial reflection effect can be formed without extra partially reflective surface (PRS), which is commonly required by a conventional FPC. At the same time, due to relative high dielectric of the DFSC, antenna size can be significantly miniaturized. Furthermore, we modified the structure of DFSC to form a reverse-stepped shape, contributing to bandwidth and gain enhancement of the FPC antenna. The proposed antenna consists of only two components, a feeding antenna and the proposed DFSC. The size of the antenna is 4λ0*4λ0, which is much smaller when compared with recently reported FPC type of antennas. For demonstration, the antenna was designed, manufactured, and measured. The measured results show that the working bandwidth of the antenna is 15.9 %. It yields a peak gain of 18.3 dBi and in-band radiation pattern is stable. The proposed antenna has superior advantages in terms of size, bandwidth, and simplicity.
- 27 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 24 (4) , 983-987
Millimeter-Wave Differentially Fed Single-Layered Circularly Polarized Antenna
A millimeter-wave (mmw) circularly polarized (CP) antenna in single-layered laminate is proposed in this paper. For performances, it yields obvious advantages in terms of profile (single layer), gain and bandwidth when compared with recently reported high gain CP antennas. For design method, it is the first attempt to introduce I-shaped differentially-fed slots to achieve enhanced bandwidth over the traditional slot antenna. Then we add complementary dipoles to the same plane of the I-shaped slots, contributing to CP radiation. Then, we build 1×8 antenna array to increase the gain of the proposed CP element. For demonstration, a single-layered CP antenna array operating at 77 GHz is designed, fabricated, and measured. Measured results show that the overlapped bandwidth for impedance matching, axial ratio and gain is 13% (72 to 82 GHz). It realizes a flat in-band gains with a peak gain of 13 dBic. It is a promising candidate for mmw vehicular communications systems such as unmanned aerial vehicle (UAV) and motor car, where requires low profile, CP radiation and fast data transmission speed.
- 27 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 24 (4) , 983-987
Millimeter-Wave Differentially Fed Single-Layered Circularly Polarized Antenna
A millimeter-wave (mmw) circularly polarized (CP) antenna in single-layered laminate is proposed in this paper. For performances, it yields obvious advantages in terms of profile (single layer), gain and bandwidth when compared with recently reported high gain CP antennas. For design method, it is the first attempt to introduce I-shaped differentially-fed slots to achieve enhanced bandwidth over the traditional slot antenna. Then we add complementary dipoles to the same plane of the I-shaped slots, contributing to CP radiation. Then, we build 1×8 antenna array to increase the gain of the proposed CP element. For demonstration, a single-layered CP antenna array operating at 77 GHz is designed, fabricated, and measured. Measured results show that the overlapped bandwidth for impedance matching, axial ratio and gain is 13% (72 to 82 GHz). It realizes a flat in-band gains with a peak gain of 13 dBic. It is a promising candidate for mmw vehicular communications systems such as unmanned aerial vehicle (UAV) and motor car, where requires low profile, CP radiation and fast data transmission speed.
- 3 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (2) , 1373-1384
A High-Gain, Wideband, Circularly Polarized Antenna With Multibeam Radiation for Millimeter-Wave Applications
This paper proposes a wideband differential fed CP antenna (48% overlapped bandwidth, which is the minimum value of AR bandwidth, gain bandwidth and impedance matching bandwidth) with multiple beams radiation across V- and W-band enabled by a parabolic reflector, a long-slot radiator and a wideband 3D printed polarizer. The long slot structure is an array consists with SIW based open slot elements (the vias besides a conventional SIW slot are moved, to form an open slot), which yields wideband characteristics when compared with traditional slot array. Cooperating with wideband parabolic reflector and modified 3D printed polarizer, it finally achieves 48% CP bandwidth. Finally, by setting multiple ports on the feeding network, multi-beam radiation can be achieved. For validation, a multi-beam CP antenna operating from 58 to 94.5 GHz with 20.5 dBic peak gain level and three radiation beams is fabricated and measured. Based on the authors’ extensive research, the proposed antenna yields a superior bandwidth when compared with recently reported mm-wave long slot structures and high-gain CP antennas.
- 3 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (2) , 1373-1384
A High-Gain, Wideband, Circularly Polarized Antenna With Multibeam Radiation for Millimeter-Wave Applications
This paper proposes a wideband differential fed CP antenna (48% overlapped bandwidth, which is the minimum value of AR bandwidth, gain bandwidth and impedance matching bandwidth) with multiple beams radiation across V- and W-band enabled by a parabolic reflector, a long-slot radiator and a wideband 3D printed polarizer. The long slot structure is an array consists with SIW based open slot elements (the vias besides a conventional SIW slot are moved, to form an open slot), which yields wideband characteristics when compared with traditional slot array. Cooperating with wideband parabolic reflector and modified 3D printed polarizer, it finally achieves 48% CP bandwidth. Finally, by setting multiple ports on the feeding network, multi-beam radiation can be achieved. For validation, a multi-beam CP antenna operating from 58 to 94.5 GHz with 20.5 dBic peak gain level and three radiation beams is fabricated and measured. Based on the authors’ extensive research, the proposed antenna yields a superior bandwidth when compared with recently reported mm-wave long slot structures and high-gain CP antennas.