MIMohammad Hossein Izadifard

Mohammad Hossein Izadifard

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mohammad Hossein Izadifard has a total of 29 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Velocity jump of Newtonian droplets in viscoelastic fluids: analytical and experimental study

    by Mahmood Norouzi, Amir Hossein Adibimanesh, Mohammad Kazem Sheykhian, Amin Emamian, Mohammad Hossein Izadifard, Mohammad Hasan Kayhani, Mirae Kim, Kyung Chun Kim

    This study presents a combined analytical and experimental investigation into the rising dynamics of Newtonian droplets in viscoelastic fluids, focusing on discontinuous transitions in droplet velocity. Although velocity jumps have been observed in gas bubbles, this work is the first systematic investigation of the phenomenon in Newtonian droplets. Analytically, a triple-perturbation approach is developed using Reynolds ( Re ), Deborah ( De ) and capillary ( Ca ) numbers as expansion parameters. The surrounding viscoelastic medium is modelled using the nonlinear-Giesekus constitutive equation. The analysis reveals that increasing Deborah number intensifies and reorients normal stresses – particularly the polar ( $\theta$ -direction) and hoop components – along the droplet interface. These stresses migrate rearward with increasing elasticity, resulting in localised elongational flows and concentrated radial stresses near the rear stagnation point, which indicates the onset of elastic instabilities. Experimentally, Newtonian droplets are introduced into a variety of exterior fluids: (i) quasilinear Boger fluids, which are constant-viscosity viscoelastic solutions that isolate elastic effects; and (ii) a strongly nonlinear viscoelastic solution, which exhibits both high elasticity and significant shear-thinning behaviour. Equivalent Newtonian fluids of matched viscosity are also used as controls. Viscoelastic fluids are solutions of polyacrylamide in the water–glycerine mixture. Across all experiments, the dimensionless ranges were $\textit{Re}\approx 6\times 10^{-4}{-}4.59$ , $\textit{De}\approx 0.057{-}0.802$ and $\textit{Ca}\approx 0.0026{-}0.638$ , framing the scope of applicability. The experimental observations challenge the classical expectation of smooth droplet motion and demonstrate that Newtonian droplets in viscoelastic environments can exhibit sharp, weak or no velocity jumps, depending on the balance between elasticity, viscosity and deformability.


  • Analytical and numerical study of Taylor–Couette flow of viscoelastic fluid between finite cylinders

    by Amirali Fazli Yeknomi, Mahmood Norouzi, Seyed Majid Hashemian, Kayvan Sadeghy, Mohammad Hossein Izadifard

    The Taylor–Couette (TC) geometry is a fundamental configuration in fluid mechanics and rheometry for investigating instabilities in viscoelastic fluids. In this work, we present a combined analytical and numerical study of inertial viscoelastic TC flow with finite aspect ratio using the Oldroyd-B constitutive model. The analytical formulation is developed via a perturbation approach, with the curvature ratio as the perturbation parameter, and solved using the Ritz variational method to determine the velocity field, stream function, secondary flow characteristics, and instability threshold. Numerical simulations based on a finite-difference scheme on a staggered grid validate the analytical predictions. The results show that, for any finite aspect ratio, a pair of Taylor vortices (TVs) forms both in the absence of elasticity, driven by viscous forces, and in the absence of viscosity, induced by gradients of the first normal stress difference. Increasing the Reynolds number shifts vortex centers toward the bulk and smooths corner singularities near the walls. Beyond a critical Reynolds number, the TV mode transitions to disordered vortices, defining a clear instability threshold. The aspect ratio and viscosity ratio strongly influence secondary flow structures, while elasticity suppresses inertial effects and modulates vortex strength. This work establishes, for the first time, an analytical framework based on the Ritz method to predict the onset of instability in finite aspect ratio TC flows. The results provide a basis for future studies of instabilities and applications involving polymer solutions and biofluids in rotational systems.

  • Viscoelastic droplets via flow-focusing: From dripping to jetting and beads-on-a-string structures

    by Amirreza Neshat, Mahmood Norouzi, Mohsen Nazari, Hadi Gerivani, Mohammad Hossein Izadifard

    This study explores the formation dynamics of Boger (or near-Boger) and Newtonian droplets with matched shear viscosities in a flow-focusing microchannel. The viscoelastic dispersed phases—200 and 400 ppm polyacrylamide in aqueous glycerol—exhibited near-constant viscosities of 104 and 126 mPa s, respectively. The continuous phase was a surfactant-laden Newtonian transformer oil (30 mPa s). By isolating elasticity from other non-Newtonian effects, we demonstrate its pronounced influence on droplet generation, even at low Capillary numbers (on the order of 10−4 to 10−3). Four distinct breakup regimes were identified: Parallel flow (PF), Dripping (D), Jetting (J), and the viscoelastic-specific beads-on-a-string (BOAS) structures. Elasticity notably suppresses the dripping regime while expanding the jetting domain, where BOAS structures emerge. Regime maps reveal that jetting broadens with increased continuous-phase flow rate (Qc) and contracts with higher dispersed-phase flow rate (Qd). Elasticity also transforms the satellite-droplet formation mechanism. Instead of shedding tiny droplets, the stabilized filament breaks into large secondary droplets comparable to the primary ones. This stabilizing effect is quantitatively confirmed by a threefold increase in normalized jet breakup length. Overall, this research demonstrates that the final fracture morphology is governed by the Elastocapillary number (Ec), which quantifies the competition between stabilizing elastic stresses and destabilizing capillary forces. This provides a predictive framework for understanding and controlling the droplet generation process in complex non-Newtonian multiphase systems.

  • The role of nonlinear viscoelasticity in journal bearing lubrication: Insight from the Phan–Thien–Tanner model

    by Melika Mokhtari Sharghi, Mahmood Norouzi, Ali Abbaspur, Mohammad Hossein Izadifard

    This research offers a numerical study of viscoelastic lubrication in journal bearings employing the Phan–Thien–Tanner (PTT) constitutive equation. This equation characterizes the reciprocity between the viscous and elastic properties of materials. Furthermore, it accounts for shear thinning and differences in normal stress. The model records nonlinear elastic effects and simulates complex geometries and flow conditions. This research examines the impact of the following characteristic parameters—the elongational parameter, the Deborah number, and eccentricity ratio, on the pressure distribution, shear stress, the first normal stress difference, load capacity, friction coefficient, and stress ratio. The results indicate that a low elongational property can sustain larger loads while providing a smaller friction coefficient, both of which are desirable features in journal bearing lubricants. As the eccentricity ratio increases, pressure rises, and in high-pressure regions, the lubricant resists deformation, leading to high shear stress. Factors affecting the elasticity of fluids contribute to the accumulation of normal stresses in both shear and extensional flow.


  • Optimized neural network framework for MRE fabrication with targeted stiffness and damping

    by Mohammad Hossein Izadifard, Mahmood Norouzi, Seyyed Mojtaba Varedi-Koulaei, Mojtaba Ghatee, Amirmasoud Alimardan, Mohammad Mehdi Zolfagharian

    Magnetorheological elastomers (MRE) are versatile smart materials capable of modulating their mechanical properties under external magnetic fields, unlocking transformative potential for applications demanding adaptive stiffness and damping. This work introduces a novel two-phase approach—a forward modelling phase followed by a design optimization phase—to design MREs with precisely tailored viscoelastic properties. Seven MRE samples, spanning isotropic and anisotropic configurations, are fabricated by varying chain orientations and curing magnetic fields. Extensive rheological characterization is conducted under multiple temperatures, magnetic fields, and frequencies, generating a dataset of 4200 points. In the first phase, a Multilayer Perceptron (MLP) neural network is trained on this dataset, with its architecture optimized using two metaheuristic algorithms: Particle Swarm Optimization (PSO) and the Whale Optimization Algorithm (WOA). Results reveal that the three-hidden-layer MLP, optimized by PSO, outperforms other configurations with a minimum Root Mean Squared Error (RMSE) of 1571.3, surpassing the R 2 = 0.97 achieved by a parametric fractional model on the same dataset. Conversely, WOA demonstrates a marginal edge in the four-hidden-layer configuration. Subsequently, the best-performing forward model among the tested configurations serves as a surrogate in the second-phase design procedure. PSO is reapplied to determine the optimal parameters—namely temperature, operating and preparatory magnetic fields, chain orientation, and angular frequency—to achieve the desired storage and loss moduli. Four new MRE samples are fabricated according to two of these optimized parameters, while the remaining parameters are applied during rheological testing. The final experimental results confirm that the maximum discrepancy between the designed and desired moduli is limited to ±7.5%. This framework streamlines MRE customization, minimizing trial and error efforts and significantly reducing fabrication costs and time. Its robustness paves the way for advanced applications in vibration isolation, soft robotics, and adaptive devices requiring precise stiffness and damping modulation.


  • Three-dimensional Phan-Thien-Tanner viscoelastic flows around a sphere

    by Moein Zamani–Taghizadeh–Rabe, Mahmood Norouzi, Ali Abass Nejad, Ali Minaeian, Mohammad Hossein Izadifard

    This study investigates the steady and unsteady flow of a viscoelastic fluid around a sphere in three-dimensional space. Numerical simulations using the finite volume method incorporated a logarithmic mapping technique to overcome divergence issues at high elastic numbers. The fluid's behavior was characterized by the Phan-Thien-Tanner model, renowned for its accuracy and parametric simplicity. Key findings reveal that viscosity variations and stress relaxation times are pivotal in shaping the fluid's viscoelastic properties, surpassing the influence of other factors. Notably, the drag coefficient exhibited diverse behaviors—in some cases increasing, in others decreasing, and at times remaining constant—across different elasticity numbers. The study also explored the impact of fluid dilution, elasticity, and viscosity ratio on shear stress and drag coefficient variations, highlighting the profound role of elasticity in modulating the drag coefficient. A rise in velocity, elasticity number, viscosity ratio, and slip parameter was found to correspond with an increase in the drag coefficient, whereas an enhancement of the first model parameter reduced velocity, allowing viscous losses to dominate flow dynamics. The critical Reynolds number for Newtonian fluids was determined to be 300, with a noticeable decline as elasticity increased. The viscosity ratio demonstrated a strong influence on the critical Reynolds number, while the model parameters had minimal impact. Additionally, it was observed that as the vortex separation ratio increased, vortex length extended, and the separation angle decreased.


  • Experimental characterization and fractional modelling of anisotropic magnetorheological elastomers under the influence of temperature and magnetic fields

    by Mohammad Hossein Izadifard, Mahmood Norouzi, Mojtaba Ghatee, Mohammad Bagher Nazari, Amirmasoud Alimardan

    The multifaceted influence of combined variables on the mechanical-magnetorheological properties of isotropic and anisotropic MREs in a shear state is probed in this research.