Ali M. AlSumaiti
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ali M. AlSumaiti has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Waleed Alameri
Research and Innovation Center on CO2 and Hydrogen (RICH), Department of Chemical and Petroleum Engineering, Khalifa University of Science & Technology
6 shared publications - Shehadeh Masalmeh
Abu Dhabi National Oil Company (ADNOC)
5 shared publications - Emad Waleed Al Shalabi
Research and Innovation Center on CO2 and Hydrogen (RICH), Chemical and Petroleum Engineering Department, Khalifa University of Science and Technology (KU), Abu Dhabi, UAE
4 shared publications - Anoo Sebastian
Department of Chemical and Petroleum Engineering, Khalifa University of Science and Technology (KU)
3 shared publications - Kishore K. Mohanty
The University of Texas at Austin
3 shared publications - Muhammad Mushtaq
Department of Chemical and Petroleum Engineering, Khalifa University of Science and Technology (KU)
3 shared publications
Latest Publications
- 26 February 2025
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 30 (05) , 2800-2818
ATBS Polymer Injectivity in 22–86 md Carbonate Cores: Impacts of Polymer Filtration, Mechanical Shearing, and Oil Presence
Summary: Polymer injectivity into porous media is one of the main issues crucial for the success of a polymer flood project, especially in low-permeability carbonates. Most studies on polymer flooding have focused on high-permeability carbonate cores, with few studies examining permeabilities below 100 md. This paper investigates the impact of filtration, mechanical predegradation, and oil presence on in-situ rheology and injectivity of an acrylamido-tertiary-butyl sulfonate (ATBS)-based polymer in 22–86 md carbonate cores. In this work, an ATBS polymer of 1,000 ppm concentration was used, and various pretreatment approaches were adopted to improve polymer injectivity, including prefiltration, preshearing, and their combination. Polymer injectivity and in-situ polymer rheology evaluations were performed in the absence and presence of oil using carbonate core samples with absolute permeabilities between 22 md and 86 md. For the two-phase studies, the cores were aged at irreducible water saturation and 120°C for 14 days and then flooded with glycerol followed by brine to achieve a representative immobile residual oil saturation (Sor). The corefloods were conducted at 50°C in high salinity water of 243,000 ppm. The resistance factor (RF) was calculated using water permeability at Sor to present the impact of oil presence on polymer rheology. Bulk rheological studies have confirmed that the polymer can withstand high salinity and temperature. However, achieving polymer injectivity in low permeability core samples in the absence of oil has been challenging, with a continuous increase in pressure drop. Various filtration schemes were tested in combination with shear degradation through multiple coreflooding experiments. Preshearing the polymer by 40% and subsequently filtering it through 3-µm, 1.2-µm, 0.8-µm, and 0.45-µm filter membranes improved its injectivity. With this filtration process, the polymer successfully propagated through a core plug of 64 md in the absence of oil. Experiments with oil showed improved injectivity in low-permeability core plugs. The polymer was successfully injected in samples with permeability as low as 26 md, without predegradation, using a 1.2-µm filter. Interpreting the injectivity behavior without an internal pressure tab system was challenging. At representative reservoir flow rates, near-Newtonian behavior was observed. However, there was evidence of shear thickening behavior at higher injection rates. The permeability reduction factor determined from the successful corefloods was between 2 and 4. However, it could not be verified due to the absence of polymer retention data and an internal pressure tab system. Nevertheless, it was found that the residual resistance factor (RRF) was lower when oil was present. Different approaches are reported in the literature to evaluate and improve polymer injectivity; however, there is a lack of research that combines preshear degradation, permeability, and oil presence effects. This study is distinctive in its evaluation of the impact of preshearing and prefiltration on enhancing the injectivity of an ATBS polymer in low-permeability carbonate rock. Furthermore, this study is one of the few to demonstrate the evaluation of promising ATBS-based polymer propagation through 22–86 md carbonate core plugs in the absence and presence of oil.
- 26 February 2025
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 30 (05) , 2800-2818
ATBS Polymer Injectivity in 22–86 md Carbonate Cores: Impacts of Polymer Filtration, Mechanical Shearing, and Oil Presence
Summary: Polymer injectivity into porous media is one of the main issues crucial for the success of a polymer flood project, especially in low-permeability carbonates. Most studies on polymer flooding have focused on high-permeability carbonate cores, with few studies examining permeabilities below 100 md. This paper investigates the impact of filtration, mechanical predegradation, and oil presence on in-situ rheology and injectivity of an acrylamido-tertiary-butyl sulfonate (ATBS)-based polymer in 22–86 md carbonate cores. In this work, an ATBS polymer of 1,000 ppm concentration was used, and various pretreatment approaches were adopted to improve polymer injectivity, including prefiltration, preshearing, and their combination. Polymer injectivity and in-situ polymer rheology evaluations were performed in the absence and presence of oil using carbonate core samples with absolute permeabilities between 22 md and 86 md. For the two-phase studies, the cores were aged at irreducible water saturation and 120°C for 14 days and then flooded with glycerol followed by brine to achieve a representative immobile residual oil saturation (Sor). The corefloods were conducted at 50°C in high salinity water of 243,000 ppm. The resistance factor (RF) was calculated using water permeability at Sor to present the impact of oil presence on polymer rheology. Bulk rheological studies have confirmed that the polymer can withstand high salinity and temperature. However, achieving polymer injectivity in low permeability core samples in the absence of oil has been challenging, with a continuous increase in pressure drop. Various filtration schemes were tested in combination with shear degradation through multiple coreflooding experiments. Preshearing the polymer by 40% and subsequently filtering it through 3-µm, 1.2-µm, 0.8-µm, and 0.45-µm filter membranes improved its injectivity. With this filtration process, the polymer successfully propagated through a core plug of 64 md in the absence of oil. Experiments with oil showed improved injectivity in low-permeability core plugs. The polymer was successfully injected in samples with permeability as low as 26 md, without predegradation, using a 1.2-µm filter. Interpreting the injectivity behavior without an internal pressure tab system was challenging. At representative reservoir flow rates, near-Newtonian behavior was observed. However, there was evidence of shear thickening behavior at higher injection rates. The permeability reduction factor determined from the successful corefloods was between 2 and 4. However, it could not be verified due to the absence of polymer retention data and an internal pressure tab system. Nevertheless, it was found that the residual resistance factor (RRF) was lower when oil was present. Different approaches are reported in the literature to evaluate and improve polymer injectivity; however, there is a lack of research that combines preshear degradation, permeability, and oil presence effects. This study is distinctive in its evaluation of the impact of preshearing and prefiltration on enhancing the injectivity of an ATBS polymer in low-permeability carbonate rock. Furthermore, this study is one of the few to demonstrate the evaluation of promising ATBS-based polymer propagation through 22–86 md carbonate core plugs in the absence and presence of oil.
- 12 November 2024
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 30 (01) , 409-422
Measurement of Acrylamido Tertiary Butyl Sulfonate Polymer Retention on Limestone by Three Methods Under Varying Temperature and Oil Presence
Summary: Polymer retention poses a significant challenge in polymer flooding applications, emphasizing the importance of accurately determining retention levels for successful project design. In carbonate reservoirs of the Middle East, where temperatures exceed 90°C, conducting adsorption tests under similar temperature conditions becomes crucial for the precise determination of adsorption values. The choice of analytical method potentially impacts the accuracy of retention measurements from effluent analysis. This study investigates the effect of temperature on the performance of a polymer, specifically its rheological behavior and retention. Rheological and polymer flooding experiments were carried out using an acrylamido tertiary butyl sulfonate (ATBS)-based polymer in formation water (167,114 ppm) at different temperatures (25°C, 60°C, and 90°C) with required oxygen control measures. Dynamic polymer retention was conducted in both the absence of oil (single-phase tests) and the presence of oil (two-phase tests). In addition, different analytical techniques were evaluated, including viscosity measurements, ultraviolet (UV)-visible spectroscopy, and total organic carbon-total nitrogen (TOC-TN) analysis, to determine the most accurate method for measuring the polymer concentration with the least associated uncertainty. Furthermore, the study investigates the effects of these uncertainties on the final dynamic polymer retention values by applying the propagation of error theory. The effluent polymer concentration was determined using viscosity correlation, UV spectrometry, and TOC-TN analysis, all of which were reliable methods with coefficient of determination (R2) values of ~0.99. The study analyzed the effects of flow through porous media and backpressure regulator on polymer degradation. The results showed that the degradation rates were around 2% for flow through porous media and 16% for mechanical degradation due to the backpressure regulator for all temperature conditions. For the effluent sample, the concentration of polymer was lower when using the viscosity method due to polymer degradation. However, the TOC-TN and UV methods were unaffected as they measured the TN and absorbance at a specific wavelength, respectively. Therefore, all viscosity results were corrected for polymer degradation effects in all tests. During the two-phase coreflooding experiment conducted at 25°C, the accuracy of the UV spectrometry and viscosity measurements was affected by the presence of oil, rendering these methods unsuitable. However, the TOC-TN measurements were able to determine effluent polymer concentration and, subsequently, the retention value. Moreover, the use of glycerin preflush to inhibit oil production during polymer injection in the two-phase studies showed that all three methods were appropriate. The error range was obtained using the propagation of error theory for all the methods. Accordingly, it was noted that the temperature did not affect the dynamic retention values in both single-phase and two-phase conditions. The findings of this study highlight that when adequate oxygen control measures are implemented, the temperature does not exhibit a statistically significant impact on the retention of the ATBS-based polymer under investigation. Furthermore, TOC-TN has been identified as the optimal analytical method due to its minimal uncertainties and ease of measuring polymer concentration under varying experimental conditions.
- 12 November 2024
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 30 (01) , 409-422
Measurement of Acrylamido Tertiary Butyl Sulfonate Polymer Retention on Limestone by Three Methods Under Varying Temperature and Oil Presence
Summary: Polymer retention poses a significant challenge in polymer flooding applications, emphasizing the importance of accurately determining retention levels for successful project design. In carbonate reservoirs of the Middle East, where temperatures exceed 90°C, conducting adsorption tests under similar temperature conditions becomes crucial for the precise determination of adsorption values. The choice of analytical method potentially impacts the accuracy of retention measurements from effluent analysis. This study investigates the effect of temperature on the performance of a polymer, specifically its rheological behavior and retention. Rheological and polymer flooding experiments were carried out using an acrylamido tertiary butyl sulfonate (ATBS)-based polymer in formation water (167,114 ppm) at different temperatures (25°C, 60°C, and 90°C) with required oxygen control measures. Dynamic polymer retention was conducted in both the absence of oil (single-phase tests) and the presence of oil (two-phase tests). In addition, different analytical techniques were evaluated, including viscosity measurements, ultraviolet (UV)-visible spectroscopy, and total organic carbon-total nitrogen (TOC-TN) analysis, to determine the most accurate method for measuring the polymer concentration with the least associated uncertainty. Furthermore, the study investigates the effects of these uncertainties on the final dynamic polymer retention values by applying the propagation of error theory. The effluent polymer concentration was determined using viscosity correlation, UV spectrometry, and TOC-TN analysis, all of which were reliable methods with coefficient of determination (R2) values of ~0.99. The study analyzed the effects of flow through porous media and backpressure regulator on polymer degradation. The results showed that the degradation rates were around 2% for flow through porous media and 16% for mechanical degradation due to the backpressure regulator for all temperature conditions. For the effluent sample, the concentration of polymer was lower when using the viscosity method due to polymer degradation. However, the TOC-TN and UV methods were unaffected as they measured the TN and absorbance at a specific wavelength, respectively. Therefore, all viscosity results were corrected for polymer degradation effects in all tests. During the two-phase coreflooding experiment conducted at 25°C, the accuracy of the UV spectrometry and viscosity measurements was affected by the presence of oil, rendering these methods unsuitable. However, the TOC-TN measurements were able to determine effluent polymer concentration and, subsequently, the retention value. Moreover, the use of glycerin preflush to inhibit oil production during polymer injection in the two-phase studies showed that all three methods were appropriate. The error range was obtained using the propagation of error theory for all the methods. Accordingly, it was noted that the temperature did not affect the dynamic retention values in both single-phase and two-phase conditions. The findings of this study highlight that when adequate oxygen control measures are implemented, the temperature does not exhibit a statistically significant impact on the retention of the ATBS-based polymer under investigation. Furthermore, TOC-TN has been identified as the optimal analytical method due to its minimal uncertainties and ease of measuring polymer concentration under varying experimental conditions.
- Open Access
- 12 June 2024
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 29 (09) , 4988-5001
Investigating the Effect of Water Softening on Polymer Adsorption onto Carbonates through Single-Phase and Two-Phase Experiments
Summary: Polymer retention is considered a major challenge in polymer flooding applications, especially in carbonates. This is due to the prevailing conditions of low permeability (85°C), and high salinity (>100,000 ppm) generally found in these formations, which limit the effectiveness of commonly used polymers such as hydrolyzed polyacrylamide (HPAM) and xanthan gum. To address these challenges, a polymer based on acrylamide tertiary butyl sulfonate (ATBS) has been used due to its tolerance to high-temperature and -salinity conditions. However, the high cost of manufacturing these polymers, combined with their anionic properties that promote adsorption onto positively charged carbonate rocks, necessitates the exploration of methods to reduce polymer retention. In this study, we aim to determine the sufficient concentration of hardness ions (Ca2+ and Mg2+) required to significantly reduce the adsorption of this polymer. The study is unique in its focus on mitigating polymer retention in carbonate formations using softened brine, as no prior research has investigated this aspect. Four different brines were investigated with a salinity of 8,000 ppm total dissolved salts (TDS) and varying ionic composition designed mainly by eliminating the hardness-causing ions, Ca2+ and Mg2+. A geochemical study was performed using the PHREEQC software to analyze the interaction between these injected brines and the rock. Furthermore, comprehensive rheological and static adsorption studies were performed at a temperature of 25°C using the potential ATBS-based polymer to evaluate the polymer performance and adsorption in these brines. Later, dynamic adsorption studies were conducted in both single-phase and two-phase conditions to further quantify polymer adsorption. The geochemical study showed an anhydrite saturation index (SI) of less than 0.5 for all the brines used when interacting with the rock, indicating a very low tendency for calcium sulfate precipitation. Furthermore, the rheological studies showed that polymer viscosity significantly increased with reduced hardness, where a polymer solution viscosity of 7.5 cp was obtained in zero hardness brine, nearly 1.5 times higher than the polymer viscosity of the base makeup brine of 8,000 ppm. Moreover, it was observed that, by carefully tuning the concentrations of the divalent cations, the polymer concentration consumption for the required target viscosity was reduced by 40–50%. For the single-phase static adsorption experiments, the polymer solution in softened brines resulted in lower adsorption in the range of 37–62 µg/g-rock as opposed to 102 µg/g-rock for the base makeup brine. On the other hand, the single-phase dynamic adsorption results showed an even lowered polymer adsorption of 33 µg/g-rock for the softened brine compared with 45 µg/g-rock for the base makeup brine. Additionally, the single-phase dynamic adsorption studies showed a remarkable improvement in polymer injectivity using softened brine. The polymer retention in wettability-altered cores was further reduced. The study highlights that water softening improves the performance of polymers, specifically in terms of lowering polymer adsorption. It concludes that a threshold hardness level (Ca2+ and Mg2+) of approximately 100 ppm is sufficient to achieve a significant reduction in polymer adsorption for the tested experimental conditions. In this paper, we show that the softened water increases the polymer viscosity and reduces polymer adsorption, which leads to an overall reduction in polymer consumption. Hence, the softened makeup water has the potential to enhance the application envelope of this potential polymer for polymer flood, especially in the case of carbonate reservoirs.
- 12 June 2024
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 29 (09) , 4988-5001
Open AccessInvestigating the Effect of Water Softening on Polymer Adsorption onto Carbonates through Single-Phase and Two-Phase Experiments
Summary: Polymer retention is considered a major challenge in polymer flooding applications, especially in carbonates. This is due to the prevailing conditions of low permeability (85°C), and high salinity (>100,000 ppm) generally found in these formations, which limit the effectiveness of commonly used polymers such as hydrolyzed polyacrylamide (HPAM) and xanthan gum. To address these challenges, a polymer based on acrylamide tertiary butyl sulfonate (ATBS) has been used due to its tolerance to high-temperature and -salinity conditions. However, the high cost of manufacturing these polymers, combined with their anionic properties that promote adsorption onto positively charged carbonate rocks, necessitates the exploration of methods to reduce polymer retention. In this study, we aim to determine the sufficient concentration of hardness ions (Ca2+ and Mg2+) required to significantly reduce the adsorption of this polymer. The study is unique in its focus on mitigating polymer retention in carbonate formations using softened brine, as no prior research has investigated this aspect. Four different brines were investigated with a salinity of 8,000 ppm total dissolved salts (TDS) and varying ionic composition designed mainly by eliminating the hardness-causing ions, Ca2+ and Mg2+. A geochemical study was performed using the PHREEQC software to analyze the interaction between these injected brines and the rock. Furthermore, comprehensive rheological and static adsorption studies were performed at a temperature of 25°C using the potential ATBS-based polymer to evaluate the polymer performance and adsorption in these brines. Later, dynamic adsorption studies were conducted in both single-phase and two-phase conditions to further quantify polymer adsorption. The geochemical study showed an anhydrite saturation index (SI) of less than 0.5 for all the brines used when interacting with the rock, indicating a very low tendency for calcium sulfate precipitation. Furthermore, the rheological studies showed that polymer viscosity significantly increased with reduced hardness, where a polymer solution viscosity of 7.5 cp was obtained in zero hardness brine, nearly 1.5 times higher than the polymer viscosity of the base makeup brine of 8,000 ppm. Moreover, it was observed that, by carefully tuning the concentrations of the divalent cations, the polymer concentration consumption for the required target viscosity was reduced by 40–50%. For the single-phase static adsorption experiments, the polymer solution in softened brines resulted in lower adsorption in the range of 37–62 µg/g-rock as opposed to 102 µg/g-rock for the base makeup brine. On the other hand, the single-phase dynamic adsorption results showed an even lowered polymer adsorption of 33 µg/g-rock for the softened brine compared with 45 µg/g-rock for the base makeup brine. Additionally, the single-phase dynamic adsorption studies showed a remarkable improvement in polymer injectivity using softened brine. The polymer retention in wettability-altered cores was further reduced. The study highlights that water softening improves the performance of polymers, specifically in terms of lowering polymer adsorption. It concludes that a threshold hardness level (Ca2+ and Mg2+) of approximately 100 ppm is sufficient to achieve a significant reduction in polymer adsorption for the tested experimental conditions. In this paper, we show that the softened water increases the polymer viscosity and reduces polymer adsorption, which leads to an overall reduction in polymer consumption. Hence, the softened makeup water has the potential to enhance the application envelope of this potential polymer for polymer flood, especially in the case of carbonate reservoirs.
- 16 February 2024
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 29 (05) , 2686-2702
Assessment of World’s First Two Polymer Injectivity Tests Performed in Two Giant High-Temperature/High-Salinity Carbonate Reservoirs Using Single-Well Simulation Models and Pressure Falloff Tests Analysis
Summary: Polymer flooding is a mature enhanced oil recovery (EOR) technology that has been widely implemented around the world for more than 60 years. Polymer flooding mostly targets medium- to high-permeability sandstone reservoirs with moderate salinity, hardness, and temperatures. However, in the last few years, the envelope of polymer flooding has been expanded to harsher reservoir conditions of high-temperature and high-salinity mixed-wet to oil-wet heterogeneous carbonate reservoirs. Development of novel polymers and innovative field application concepts has allowed for the reconsideration of polymer-based EOR as a promising technology to improve sweep efficiency for these challenging reservoirs. Polymer injectivity is one of the key challenges for polymer flooding projects and requires a rigorous derisking program that includes laboratory and field testing. A comprehensive laboratory program was designed to assess and investigate polymer thermal stability, polymer rheology in porous media, adsorption, and injectivity using reservoir core samples. In addition, two polymer injectivity tests (PITs) were performed in two giant light oil (0.3 cp) carbonate reservoirs in onshore Abu Dhabi under harsh conditions of high salinity (>200 g/L), high divalent ions (>20 g/L), high temperature (>250°F), and H2S concentration of up to 40 ppm. The polymer used during the two PITs (PIT 1 2019 and PIT 2 2021) is a new generation of EOR polymer (SAV 10) with high 2-acrylamido-tertiary-butyl sulfonic acid content that was specifically developed to tolerate such harsh conditions. This paper is focused on the interpretation of the PITs and lessons learned for future polymer-based EOR projects. The detailed data acquired in both tests were used to evaluate the polymer injectivity at representative field conditions and in-depth mobility reduction. The PITs together with the extensive laboratory studies are part of a thorough derisking program for the upcoming world’s first innovative hybrid EOR multiwell pilots—simultaneous injection of miscible gas and polymer (SIMGAP) and simultaneous injection of water and polymer (SIWAP). Both PITs are composed of three stages that include a multirate waterflood baseline, polymer injection using different rates, and polymer concentrations followed by extended chase waterflooding. In addition, a sequence of multiple pressure falloff (PFO) tests was acquired during the PIT executions and analyzed to obtain the required uncertainty parameters for the history-matching exercise. Polymer preshearing was considered as part of both PIT programs with the aim to homogenize the polymer molecular weight distribution and reduce possible shear-thickening effects near the wellbore as per laboratory measurements. Two single-well 3D simulation models were built to incorporate the information from polymer laboratory studies and to interpret the large field data sets acquired during the PITs. Lessons learned from PIT 1 allowed us to optimize the PIT 2 design program and achieve better understanding of polymer characteristics. The interpretation of the pressure transient analysis (PTA) of the PFO tests and the 3D simulation models of the two PITs confirmed the generation of polymer banks and demonstrated effective propagation of the polymer into the reservoirs at target concentrations and representative rates of the future SIWAP and SIMGAP interwell pilots.
- 16 February 2024
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 29 (05) , 2686-2702
Assessment of World’s First Two Polymer Injectivity Tests Performed in Two Giant High-Temperature/High-Salinity Carbonate Reservoirs Using Single-Well Simulation Models and Pressure Falloff Tests Analysis
Summary: Polymer flooding is a mature enhanced oil recovery (EOR) technology that has been widely implemented around the world for more than 60 years. Polymer flooding mostly targets medium- to high-permeability sandstone reservoirs with moderate salinity, hardness, and temperatures. However, in the last few years, the envelope of polymer flooding has been expanded to harsher reservoir conditions of high-temperature and high-salinity mixed-wet to oil-wet heterogeneous carbonate reservoirs. Development of novel polymers and innovative field application concepts has allowed for the reconsideration of polymer-based EOR as a promising technology to improve sweep efficiency for these challenging reservoirs. Polymer injectivity is one of the key challenges for polymer flooding projects and requires a rigorous derisking program that includes laboratory and field testing. A comprehensive laboratory program was designed to assess and investigate polymer thermal stability, polymer rheology in porous media, adsorption, and injectivity using reservoir core samples. In addition, two polymer injectivity tests (PITs) were performed in two giant light oil (0.3 cp) carbonate reservoirs in onshore Abu Dhabi under harsh conditions of high salinity (>200 g/L), high divalent ions (>20 g/L), high temperature (>250°F), and H2S concentration of up to 40 ppm. The polymer used during the two PITs (PIT 1 2019 and PIT 2 2021) is a new generation of EOR polymer (SAV 10) with high 2-acrylamido-tertiary-butyl sulfonic acid content that was specifically developed to tolerate such harsh conditions. This paper is focused on the interpretation of the PITs and lessons learned for future polymer-based EOR projects. The detailed data acquired in both tests were used to evaluate the polymer injectivity at representative field conditions and in-depth mobility reduction. The PITs together with the extensive laboratory studies are part of a thorough derisking program for the upcoming world’s first innovative hybrid EOR multiwell pilots—simultaneous injection of miscible gas and polymer (SIMGAP) and simultaneous injection of water and polymer (SIWAP). Both PITs are composed of three stages that include a multirate waterflood baseline, polymer injection using different rates, and polymer concentrations followed by extended chase waterflooding. In addition, a sequence of multiple pressure falloff (PFO) tests was acquired during the PIT executions and analyzed to obtain the required uncertainty parameters for the history-matching exercise. Polymer preshearing was considered as part of both PIT programs with the aim to homogenize the polymer molecular weight distribution and reduce possible shear-thickening effects near the wellbore as per laboratory measurements. Two single-well 3D simulation models were built to incorporate the information from polymer laboratory studies and to interpret the large field data sets acquired during the PITs. Lessons learned from PIT 1 allowed us to optimize the PIT 2 design program and achieve better understanding of polymer characteristics. The interpretation of the pressure transient analysis (PTA) of the PFO tests and the 3D simulation models of the two PITs confirmed the generation of polymer banks and demonstrated effective propagation of the polymer into the reservoirs at target concentrations and representative rates of the future SIWAP and SIMGAP interwell pilots.
- 2 October 2023
- Published by Society of Petroleum Engineers (SPE)
Comparison of Different Methods to Evaluate the Effect of Temperature on Polymer Retention and Degradation in the Presence and Absence of Oil on Carbonate Outcrops
Polymer retention poses a significant challenge in polymer flooding applications, emphasizing the importance of accurately determining retention levels for successful project design. In carbonate reservoirs of the Middle East, where temperatures exceed 90 °C, conducting adsorption tests under similar temperature conditions becomes crucial for the precise determination of adsorption values. The choice of analytical method heavily impacts the accuracy of retention measurements from effluent analysis. This study investigates the effect of temperature on the performance of a polymer, specifically its rheological behavior and retention. Rheological and polymer flooding experiments were carried out using an ATBS-based polymer in formation water (167,114 ppm) at different temperatures (25, 60, and 90 °C) with required oxygen control measures. Dynamic polymer retention was conducted in both absence of oil (single-phase tests) and presence of oil (two-phase tests). In addition, different analytical techniques were evaluated, including viscosity measurements, UV-visible spectroscopy, and TOC-TN analysis, to determine the most accurate method for measuring the polymer concentration with the least associated uncertainty. Furthermore, the study investigates the effects of these uncertainties on the final dynamic polymer retention values by applying propagation of error theory. The effluent polymer concentration was determined using viscosity correlation, UV spectrometry, and TOC-TN analysis, all of which were reliable methods with coefficient of determination (R2) values of ∼0.99. The study analyzed the effects of flow through porous media and back-pressure regulator on polymer degradation. The results showed that the degradation rates were around 2% for flow through porous media and 16% for mechanical degradation due to the back-pressure regulator for all temperature conditions. For the effluent sample, the concentration of effluents was lower when using the viscosity method due to polymer degradation. However, the TOC-TN and UV methods were unaffected as they measured the total nitrogen and absorbance at a specific wavelength, respectively. Therefore, all viscosity results were corrected for polymer degradation effects in all tests. During 60 °C single-phase studies, the dynamic retention values obtained from viscosity correlation, UV spectrometry, and TOC-TN analysis were determined to be 52 ± 3, 45 ± 5, and 48 ± 3 μg/g-rock, respectively. During the two-phase coreflooding experiment conducted at 25 °C, the accuracy of the UV spectrometry and viscosity measurements were affected by the presence of oil, rendering these methods unsuitable. However, the TOC-TN measurements were able to deliver a retention of 24± 3 μg/g-rock. Moreover, the use of glycerine preflush to inhibit oil production during polymer injection in the two-phase studies showed that all three methods were appropriate with dynamic retention values of 27± 3, 25±5, and 21±3 μg/g-rock for viscosity, UV, and TOC-TN, respectively at 60 °C. The error range was obtained using the propagation of error theory for all the methods. Accordingly, it was also noted that the temperature did not affect the dynamic retention values in both single-phase and two-phase conditions. The dynamic retention values for single-phase using the UV method and two-phase using the TOC-TN method were 45 – 56 ±5 μg/g-rock and 21 – 26 ±3μg/g-rock, respectively, for the range of temperatures applied. The findings of this study highlight that when adequate oxygen control measures are implemented, the temperature does not exhibit a statistically significant impact on the retention of the ATBS-based polymer under investigation. Furthermore, TOC-TN has been identified as the optimal analytical method due to its minimal uncertainties and ease of measuring polymer concentration under varying experimental conditions.
- 2 October 2023
- Published by Society of Petroleum Engineers (SPE)
Comparison of Different Methods to Evaluate the Effect of Temperature on Polymer Retention and Degradation in the Presence and Absence of Oil on Carbonate Outcrops
Polymer retention poses a significant challenge in polymer flooding applications, emphasizing the importance of accurately determining retention levels for successful project design. In carbonate reservoirs of the Middle East, where temperatures exceed 90 °C, conducting adsorption tests under similar temperature conditions becomes crucial for the precise determination of adsorption values. The choice of analytical method heavily impacts the accuracy of retention measurements from effluent analysis. This study investigates the effect of temperature on the performance of a polymer, specifically its rheological behavior and retention. Rheological and polymer flooding experiments were carried out using an ATBS-based polymer in formation water (167,114 ppm) at different temperatures (25, 60, and 90 °C) with required oxygen control measures. Dynamic polymer retention was conducted in both absence of oil (single-phase tests) and presence of oil (two-phase tests). In addition, different analytical techniques were evaluated, including viscosity measurements, UV-visible spectroscopy, and TOC-TN analysis, to determine the most accurate method for measuring the polymer concentration with the least associated uncertainty. Furthermore, the study investigates the effects of these uncertainties on the final dynamic polymer retention values by applying propagation of error theory. The effluent polymer concentration was determined using viscosity correlation, UV spectrometry, and TOC-TN analysis, all of which were reliable methods with coefficient of determination (R2) values of ∼0.99. The study analyzed the effects of flow through porous media and back-pressure regulator on polymer degradation. The results showed that the degradation rates were around 2% for flow through porous media and 16% for mechanical degradation due to the back-pressure regulator for all temperature conditions. For the effluent sample, the concentration of effluents was lower when using the viscosity method due to polymer degradation. However, the TOC-TN and UV methods were unaffected as they measured the total nitrogen and absorbance at a specific wavelength, respectively. Therefore, all viscosity results were corrected for polymer degradation effects in all tests. During 60 °C single-phase studies, the dynamic retention values obtained from viscosity correlation, UV spectrometry, and TOC-TN analysis were determined to be 52 ± 3, 45 ± 5, and 48 ± 3 μg/g-rock, respectively. During the two-phase coreflooding experiment conducted at 25 °C, the accuracy of the UV spectrometry and viscosity measurements were affected by the presence of oil, rendering these methods unsuitable. However, the TOC-TN measurements were able to deliver a retention of 24± 3 μg/g-rock. Moreover, the use of glycerine preflush to inhibit oil production during polymer injection in the two-phase studies showed that all three methods were appropriate with dynamic retention values of 27± 3, 25±5, and 21±3 μg/g-rock for viscosity, UV, and TOC-TN, respectively at 60 °C. The error range was obtained using the propagation of error theory for all the methods. Accordingly, it was also noted that the temperature did not affect the dynamic retention values in both single-phase and two-phase conditions. The dynamic retention values for single-phase using the UV method and two-phase using the TOC-TN method were 45 – 56 ±5 μg/g-rock and 21 – 26 ±3μg/g-rock, respectively, for the range of temperatures applied. The findings of this study highlight that when adequate oxygen control measures are implemented, the temperature does not exhibit a statistically significant impact on the retention of the ATBS-based polymer under investigation. Furthermore, TOC-TN has been identified as the optimal analytical method due to its minimal uncertainties and ease of measuring polymer concentration under varying experimental conditions.
- 27 April 2015
- Published by Society of Petroleum Engineers (SPE)
Experimental and Numerical Modeling of Low-Salinity Waterflood in a Low Permeability Carbonate Reservoir
Low-salinity waterflooding in carbonate reservoirs is of great interest because of the potential for increased recovery of oil. However, the exact mechanism of low-salinity oil recovery is not well understood. It has been suggested that the main mechanism is wettability alteration resulting from the interaction of Na+, Cl-, Ca2+, Mg2+, SO42-, and RCOO- in the electrical double layer (EDL) near the surface of carbonate pores. In this paper, we present laboratory experiments and numerical modeling in low-permeability carbonate cores to assess this assertion. Seawater followed by series of low-salinity waterflood experiments were performed on several facies of carbonate reservoir. The permeability of the cores is in the range of 0.5 to 1.5 mD and porosity is from 0.18 to 0.25. Cores were aged for eight weeks at reservoir pressure and temperature. The API gravity of the oil is 32°. The IFT and contact angle measurements were performed at several brine salinities. A two phase numerical model was used to simulate oil recovery and molecular transport of salt components to investigate the wettability alteration effect. The low-salinity waterflood experiments yielded incremental oil recovery of up to nine percent. Low-salinity waterflood was observed to be more significant in less-heterogeneous and less-vuggy cores. Moreover, low-salinity waterflood altered the wettability of several one-inch diameter, crude-aged, carbonate core discs from oil-wet to intermediate-wet. Hence, the main mechanism of incremental oil recovery during low-salinity waterflood in this carbonate reservoir is wettability alteration. The mathematical model matched the oil recovery when the relative permeability functions were adjusted to account for wettability alteration effects.
- 27 April 2015
- Published by Society of Petroleum Engineers (SPE)
Experimental and Numerical Modeling of Low-Salinity Waterflood in a Low Permeability Carbonate Reservoir
Low-salinity waterflooding in carbonate reservoirs is of great interest because of the potential for increased recovery of oil. However, the exact mechanism of low-salinity oil recovery is not well understood. It has been suggested that the main mechanism is wettability alteration resulting from the interaction of Na+, Cl-, Ca2+, Mg2+, SO42-, and RCOO- in the electrical double layer (EDL) near the surface of carbonate pores. In this paper, we present laboratory experiments and numerical modeling in low-permeability carbonate cores to assess this assertion. Seawater followed by series of low-salinity waterflood experiments were performed on several facies of carbonate reservoir. The permeability of the cores is in the range of 0.5 to 1.5 mD and porosity is from 0.18 to 0.25. Cores were aged for eight weeks at reservoir pressure and temperature. The API gravity of the oil is 32°. The IFT and contact angle measurements were performed at several brine salinities. A two phase numerical model was used to simulate oil recovery and molecular transport of salt components to investigate the wettability alteration effect. The low-salinity waterflood experiments yielded incremental oil recovery of up to nine percent. Low-salinity waterflood was observed to be more significant in less-heterogeneous and less-vuggy cores. Moreover, low-salinity waterflood altered the wettability of several one-inch diameter, crude-aged, carbonate core discs from oil-wet to intermediate-wet. Hence, the main mechanism of incremental oil recovery during low-salinity waterflood in this carbonate reservoir is wettability alteration. The mathematical model matched the oil recovery when the relative permeability functions were adjusted to account for wettability alteration effects.
- 10 November 2014
- Published by Society of Petroleum Engineers (SPE)
Low-salinity Water-alternating-CO2 Flooding Enhanced Oil Recovery: Theory and Experiments
Carbon dioxide flooding is currently the most technically and economically viable enhanced oil recovery (EOR) process in carbonate and sandstone reservoirs. Low-salinity waterflood is a relatively new EOR process; and our experiments in carbonate cores show significant oil recovery improvements. We propose a new EOR process to improve economics, which involves low-salinity water-alternating-CO2 (LS-WAG) injection. To evaluate the proposed idea, three core floods and several contact angle and IFT measurements were performed. The core floods include: seawater flood, followed by low-salinity waterflood, followed by CO2 injection, which yielded fourteen, twenty-five, and thirty-eight percent additional oil recovery by CO2 from two carbonate and one sandstone experiments. We performed contact angle measurements on several low-permeability carbonate, medium-permeability Berea sandstone, and ultra-low permeability Three Forks mudstone core discs using different salinities. The contact angle measurements confirmed that favorable wettability alteration is achievable with the proposed EOR process. In addition, visual observations suggested that the proposed EOR process could be effective for cleaning the matrix-fracture interface in conventional and unconventional reservoirs. IFT measurments and modeling relevant to the EOR process is also included in this study. Low-salinity waterflood EOR Waterflooding is by far the most widely used method to increase oil recovery. Recent studies show that, by modifying the ionic content of water, wettability of reservoirs can be altered. When using seawater to alter wettability, there are different chemical mechanisms in effect between sandstone and carbonate formations. The polar components in the crude oil reacts with the positively charged carbonate rock surface differently from the negatively charged quartz/clay in sandstone formations, indicating different chemical bonding reaction mechanisms. In general, wettability alteration can be improved by modifying the ionic composition of the injected sea water (RezaeiDoust et al., 2009; Austad et al., 2010; Zekri et al., 2012; Al-Harrasi et al., 2012; Nasralla et al., 2013; Alameri et al., 2014a; Awolayo et al., 2014). Alameri et al. (2014a) through contact angle measurements and core flood experiments on carbonate cores showed improved oil recovery attributed to wettability alteration. Similar contact angle measurement and core flood experiments by Nasralla et al. (2011) showed oil-recovery improvement on sandstone cores. Study by Zekri et al. (2012) reported contact angle change with low-salinity brine, both on limestone and sandstone cores. Several brine injection concentrations were used in the experiment to examine the effect of salinity in oil recovery by varying sulfate concentrations. The study concluded that wettability alteration is the main mechanism to increase recovery by low-salinity water flooding. CO2 Flooding EOR Hydrocarbon and non-hydrocarbon gas injection in general, and CO2 floods in particular, is the leading EOR flooding process in light-oil and medium-oil, both in sandstone and carbonate reservoirs (Stalkup, 1978; Holm, 1987; Manrique et al., 2007; Ghedan 2009; Alvarado and Manrique 2010; OGJ 2014). Mostly from Permian basin, by the start of 2014, 300 M bbl/day of oil is produced by CO2-EOR in USA and is forecasted to grow to 638 M bbl/day by 2020 (Kuuskraa and Wallace 2014; OGJ 2014). Current utilization factor in mature USA CO2-EOR projects range from 5 to 15 Mcf of CO2 injected/bbl of oil produced (DOE/NETL 2014).
- 10 November 2014
- Published by Society of Petroleum Engineers (SPE)
Low-salinity Water-alternating-CO2 Flooding Enhanced Oil Recovery: Theory and Experiments
Carbon dioxide flooding is currently the most technically and economically viable enhanced oil recovery (EOR) process in carbonate and sandstone reservoirs. Low-salinity waterflood is a relatively new EOR process; and our experiments in carbonate cores show significant oil recovery improvements. We propose a new EOR process to improve economics, which involves low-salinity water-alternating-CO2 (LS-WAG) injection. To evaluate the proposed idea, three core floods and several contact angle and IFT measurements were performed. The core floods include: seawater flood, followed by low-salinity waterflood, followed by CO2 injection, which yielded fourteen, twenty-five, and thirty-eight percent additional oil recovery by CO2 from two carbonate and one sandstone experiments. We performed contact angle measurements on several low-permeability carbonate, medium-permeability Berea sandstone, and ultra-low permeability Three Forks mudstone core discs using different salinities. The contact angle measurements confirmed that favorable wettability alteration is achievable with the proposed EOR process. In addition, visual observations suggested that the proposed EOR process could be effective for cleaning the matrix-fracture interface in conventional and unconventional reservoirs. IFT measurments and modeling relevant to the EOR process is also included in this study. Low-salinity waterflood EOR Waterflooding is by far the most widely used method to increase oil recovery. Recent studies show that, by modifying the ionic content of water, wettability of reservoirs can be altered. When using seawater to alter wettability, there are different chemical mechanisms in effect between sandstone and carbonate formations. The polar components in the crude oil reacts with the positively charged carbonate rock surface differently from the negatively charged quartz/clay in sandstone formations, indicating different chemical bonding reaction mechanisms. In general, wettability alteration can be improved by modifying the ionic composition of the injected sea water (RezaeiDoust et al., 2009; Austad et al., 2010; Zekri et al., 2012; Al-Harrasi et al., 2012; Nasralla et al., 2013; Alameri et al., 2014a; Awolayo et al., 2014). Alameri et al. (2014a) through contact angle measurements and core flood experiments on carbonate cores showed improved oil recovery attributed to wettability alteration. Similar contact angle measurement and core flood experiments by Nasralla et al. (2011) showed oil-recovery improvement on sandstone cores. Study by Zekri et al. (2012) reported contact angle change with low-salinity brine, both on limestone and sandstone cores. Several brine injection concentrations were used in the experiment to examine the effect of salinity in oil recovery by varying sulfate concentrations. The study concluded that wettability alteration is the main mechanism to increase recovery by low-salinity water flooding. CO2 Flooding EOR Hydrocarbon and non-hydrocarbon gas injection in general, and CO2 floods in particular, is the leading EOR flooding process in light-oil and medium-oil, both in sandstone and carbonate reservoirs (Stalkup, 1978; Holm, 1987; Manrique et al., 2007; Ghedan 2009; Alvarado and Manrique 2010; OGJ 2014). Mostly from Permian basin, by the start of 2014, 300 M bbl/day of oil is produced by CO2-EOR in USA and is forecasted to grow to 638 M bbl/day by 2020 (Kuuskraa and Wallace 2014; OGJ 2014). Current utilization factor in mature USA CO2-EOR projects range from 5 to 15 Mcf of CO2 injected/bbl of oil produced (DOE/NETL 2014).