Emma Bianchi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Emma Bianchi has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
- Stefania Farinon
Istituto Nazionale di Fisica Nucleare Sezione di Genova, Genova, ITALY
8 shared publications - Alessandra Pampaloni
Istituto Nazionale di Fisica Nucleare Sezione di Genova, Genova, ITALY
7 shared publications - Andrea Gagno
Istituto Nazionale di Fisica Nucleare Sezione di Genova, Genova, ITALY
7 shared publications - Lucio Rossi
Department of Physics, University of Milan, Milano, Italy
6 shared publications - Marco Prioli
Laboratory of Accelerators and Applied Superconductivity, National Institute for Nuclear Physics, Milan, Italy
6 shared publications - Riccardo Musenich
Istituto Nazionale di Fisica Nucleare Sezione di Genova, Genova, ITALY
6 shared publications
Latest Publications
- 23 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Preliminary Development of an Ansys APDL Quench Suite
Simulation of quench dynamics in superconducting magnets is essential for understanding their thermal and electromagnetic behavior during fault conditions. Numerically, this represents a complex multi-physics problem encompassing thermal, electrical, and magnetic phenomena. This contribution introduces an advanced application developed using the ANSYS APDL program to simulate the quench behavior of superconducting magnets. The tool supports various geometries, including cos-theta, canted cos-theta, and solenoid configurations, making it highly versatile for diverse applications. Furthermore, the use of ANSYS APDL commercial software allows for the easy import of field information and cable configuration information directly from electromagnetic simulations. While ANSYS commonly models temperature-dependent material properties, our simulation framework extends this capability to include magnetic field-dependent material properties in the cable, such as magneto-resistivity and the superconducting critical temperature during transient states. An extensive thermal model was produced to simulate the development of Joule heating in superconducting cables, heat propagation across adjacent cables, helium cooling, and the effect of quench-heaters (QHs). Since simulating the behavior of an entire magnet in an electro-thermal transient is a particularly demanding application in terms of computation times, particular attention has been paid to developing strategies to accurately simulate magnet quench with the least possible load on the machine. We compare the performance of our tool with the already available quench simulation software and data from the quench tests of the MBRD magnet prototype for the LHC-HL upgrade.
- 23 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Preliminary Development of an Ansys APDL Quench Suite
Simulation of quench dynamics in superconducting magnets is essential for understanding their thermal and electromagnetic behavior during fault conditions. Numerically, this represents a complex multi-physics problem encompassing thermal, electrical, and magnetic phenomena. This contribution introduces an advanced application developed using the ANSYS APDL program to simulate the quench behavior of superconducting magnets. The tool supports various geometries, including cos-theta, canted cos-theta, and solenoid configurations, making it highly versatile for diverse applications. Furthermore, the use of ANSYS APDL commercial software allows for the easy import of field information and cable configuration information directly from electromagnetic simulations. While ANSYS commonly models temperature-dependent material properties, our simulation framework extends this capability to include magnetic field-dependent material properties in the cable, such as magneto-resistivity and the superconducting critical temperature during transient states. An extensive thermal model was produced to simulate the development of Joule heating in superconducting cables, heat propagation across adjacent cables, helium cooling, and the effect of quench-heaters (QHs). Since simulating the behavior of an entire magnet in an electro-thermal transient is a particularly demanding application in terms of computation times, particular attention has been paid to developing strategies to accurately simulate magnet quench with the least possible load on the machine. We compare the performance of our tool with the already available quench simulation software and data from the quench tests of the MBRD magnet prototype for the LHC-HL upgrade.
- Open Access
- 23 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
3D Mechanical Analysis of a High-Curvature Superconducting Dipole
The Superconducting Ion Gantry (SIG) project, developed in collaboration with INFN, CERN, CNAO, MedAustron and FEAC Engineering, aims to improve cancer treatment by creating compact and lightweight ion gantries. These systems allow for precise, non-coplanar irradiation while reducing damage to surrounding healthy tissues. A key element of this project is a 4 T curved superconducting dipole magnet, made with Nb-Ti Rutherford cables, featuring a 1.65 m curvature radius and an 80 mm aperture, designed for a 430 MeV/u carbon ion gantry. This study addresses the mechanical challenges of the magnet's curvature, maintained by two curved steel clamps, and the use of an indirect cooling system. To test the design and assembly process, a 30$^\circ$ demonstrator is being developed as a step toward the final 45$^\circ$ dipole. Building on previous 2D mechanical studies of the SIG curved dipole, this work presents a 3D FEM analysis of the magnet support structure. The vertical preload system aims to maximize the contact between the coil, collars, and yoke, evaluated through the percentage of elements in contact during assembly, cooldown, and energization. At the coil ends, the longitudinal preload system provides restraint and prevents additional movements during powering. All stresses remain within allowable limits, supporting the development of a design compatible with indirect cooling.
- 23 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Open Access3D Mechanical Analysis of a High-Curvature Superconducting Dipole
The Superconducting Ion Gantry (SIG) project, developed in collaboration with INFN, CERN, CNAO, MedAustron and FEAC Engineering, aims to improve cancer treatment by creating compact and lightweight ion gantries. These systems allow for precise, non-coplanar irradiation while reducing damage to surrounding healthy tissues. A key element of this project is a 4 T curved superconducting dipole magnet, made with Nb-Ti Rutherford cables, featuring a 1.65 m curvature radius and an 80 mm aperture, designed for a 430 MeV/u carbon ion gantry. This study addresses the mechanical challenges of the magnet's curvature, maintained by two curved steel clamps, and the use of an indirect cooling system. To test the design and assembly process, a 30$^\circ$ demonstrator is being developed as a step toward the final 45$^\circ$ dipole. Building on previous 2D mechanical studies of the SIG curved dipole, this work presents a 3D FEM analysis of the magnet support structure. The vertical preload system aims to maximize the contact between the coil, collars, and yoke, evaluated through the percentage of elements in contact during assembly, cooldown, and energization. At the coil ends, the longitudinal preload system provides restraint and prevents additional movements during powering. All stresses remain within allowable limits, supporting the development of a design compatible with indirect cooling.
- 12 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Manufacturing of the EuroSIG Dipole Demonstrator Magnet for Hadrontherapy
This paper reports on the updated status and manufacturing results of the EuroSIG Superconducting dipole Demonstrator Magnet (SDM-c). The SDM-c is one of the key technologies for the next-generation European heavy-ion gantry and consists of a curved cos−θ NbTi dipole with a 30° magnetic length over a 1.65 m curvature radius and a 0.15 Ts−1 ramp-rate. We summarize the milestones reached in the last year, including the production of the curved dummy coil, employed to validate the manufacturing tooling and procedures, the production of the first curved NbTi coil, and the engineering and procurement of the mechanical structure, which was also complicated by the curvature. The results show that the project is in good track to prove the feasibility of the bending magnet concept. The paper includes a discussion of the remaining challenges for the final prototype magnet, which has a 45° magnetic length and a 0.4 Ts−1 ramp-rate.
- 12 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Manufacturing of the EuroSIG Dipole Demonstrator Magnet for Hadrontherapy
This paper reports on the updated status and manufacturing results of the EuroSIG Superconducting dipole Demonstrator Magnet (SDM-c). The SDM-c is one of the key technologies for the next-generation European heavy-ion gantry and consists of a curved cos−θ NbTi dipole with a 30° magnetic length over a 1.65 m curvature radius and a 0.15 Ts−1 ramp-rate. We summarize the milestones reached in the last year, including the production of the curved dummy coil, employed to validate the manufacturing tooling and procedures, the production of the first curved NbTi coil, and the engineering and procurement of the mechanical structure, which was also complicated by the curvature. The results show that the project is in good track to prove the feasibility of the bending magnet concept. The paper includes a discussion of the remaining challenges for the final prototype magnet, which has a 45° magnetic length and a 0.4 Ts−1 ramp-rate.
- Open Access
- 15 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Advancements in the Mechanical Structure Design of FalconD: The INFN-CERN Collaboration for the Nb$_{3}$Sn 12 T Cos-Theta Dipole Within the High-Field Magnets R&D Program
The FalconD project (Future Accelerator post-LHC Optimized Nb$_{3}$Sn Dipole), conducted by INFN Genoa and Milan in collaboration with CERN, is dedicated to the development of a 1.5 m long, 12 T Nb$_{3}$Sn dipole. Nb$_{3}$Sn has already proven its effectiveness in accelerator magnets, and its application to bending dipoles is a key step toward future high-field accelerator technologies. A major challenge of the design is the mechanical structure, which must withstand the substantial Lorentz forces generated by the high magnetic field. To address this, the innovative bladder and key (B $\text{&}$ K) concept is adopted, applied here for the first time to a cos-theta dipole. This contribution presents a 2D finite element mechanical analysis of the FalconD, focusing on stress distribution and gap evolution during the main assembly and operational stages, with the aim of validating the design approach.
- 15 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Open AccessAdvancements in the Mechanical Structure Design of FalconD: The INFN-CERN Collaboration for the Nb$_{3}$Sn 12 T Cos-Theta Dipole Within the High-Field Magnets R&D Program
The FalconD project (Future Accelerator post-LHC Optimized Nb$_{3}$Sn Dipole), conducted by INFN Genoa and Milan in collaboration with CERN, is dedicated to the development of a 1.5 m long, 12 T Nb$_{3}$Sn dipole. Nb$_{3}$Sn has already proven its effectiveness in accelerator magnets, and its application to bending dipoles is a key step toward future high-field accelerator technologies. A major challenge of the design is the mechanical structure, which must withstand the substantial Lorentz forces generated by the high magnetic field. To address this, the innovative bladder and key (B $\text{&}$ K) concept is adopted, applied here for the first time to a cos-theta dipole. This contribution presents a 2D finite element mechanical analysis of the FalconD, focusing on stress distribution and gap evolution during the main assembly and operational stages, with the aim of validating the design approach.
- Open Access
- 13 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Winding Challenges and Solutions in the INFN Falcon Dipole Project
The Falcon Dipole is a project led by the Italian Institute of Nuclear Physics (INFN), which aims tofabricate a 12 T short model of a Nb$_{3}$Sn cos-theta accelerator dipole as part of the High Field Magnet (HFM) R&D program at CERN [1]. The status of the project is at the fabrication step of the first dummy coil in the industry and, in this paper, the results of the first campaign of winding tests conducted in the industry are presented. The winding process for the Falcon Dipole is challenging because the size of the Rutherford Cable used for the coils is comparable to the bore radius. This results in high bending and torsion stresses, making the cable structure unstable. To address these challenges, the previous 3D model has been modified to improve the winding feasibility. The setup has been prepared to monitor technical parameters that will help in modeling the coil geometry and identifying sources of critical issues. In this paper, the outcomes of the winding campaign are reported and the proposed changes to the coil end design to address the issues that arose are discussed.
- 13 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Open AccessWinding Challenges and Solutions in the INFN Falcon Dipole Project
The Falcon Dipole is a project led by the Italian Institute of Nuclear Physics (INFN), which aims tofabricate a 12 T short model of a Nb$_{3}$Sn cos-theta accelerator dipole as part of the High Field Magnet (HFM) R&D program at CERN [1]. The status of the project is at the fabrication step of the first dummy coil in the industry and, in this paper, the results of the first campaign of winding tests conducted in the industry are presented. The winding process for the Falcon Dipole is challenging because the size of the Rutherford Cable used for the coils is comparable to the bore radius. This results in high bending and torsion stresses, making the cable structure unstable. To address these challenges, the previous 3D model has been modified to improve the winding feasibility. The setup has been prepared to monitor technical parameters that will help in modeling the coil geometry and identifying sources of critical issues. In this paper, the outcomes of the winding campaign are reported and the proposed changes to the coil end design to address the issues that arose are discussed.
- 23 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Winding Test Results of an Innovative Technique for Block Coil Curved Dipoles in the Development of a Gantry for Hadron-Therapy
The Superconducting Ion Gantry (SIG) project is the INFN (Istituto Nazionale di Fisica Nucleare) participation in the EuroSIG collaboration between INFN, CNAO, CERN and MedAustron. The EuroSIG main focus is on the exploration of new concepts and the prototype development of superconducting magnets used in hadron-therapy treatments. More specifically, in the SIG project, we are studying the most critical aspects of a 430 MeV/u superconducting carbon-ion gantry and particular attention is given to the design of 45-degree cos$\theta$ dipoles and the construction and testing of a 30-degree demonstrator. Although the baseline of the project is centered on cos$\theta$-type magnets, we are working on an alternative strategy to mitigate the risk of failure in the construction of the demonstrator. This is a block coil type solution to avoid, with a simpler geometry, the difficulties of winding a curved cos$\theta$ dipole with significantly small curvature radius. In this context, an innovative winding technique was developed and tests have been conducted to confirm its feasibility. This contribution presents the results obtained from the winding tests in order to show the effectiveness of the method adopted to wind this type of coils and highlight possible improvements. In addition, an electromagnetic design concept for curved block coil dipoles has been developed, with the intention of proposing an optimized solution for the geometry of the coils, along with the method they can be wound.
- 23 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Winding Test Results of an Innovative Technique for Block Coil Curved Dipoles in the Development of a Gantry for Hadron-Therapy
The Superconducting Ion Gantry (SIG) project is the INFN (Istituto Nazionale di Fisica Nucleare) participation in the EuroSIG collaboration between INFN, CNAO, CERN and MedAustron. The EuroSIG main focus is on the exploration of new concepts and the prototype development of superconducting magnets used in hadron-therapy treatments. More specifically, in the SIG project, we are studying the most critical aspects of a 430 MeV/u superconducting carbon-ion gantry and particular attention is given to the design of 45-degree cos$\theta$ dipoles and the construction and testing of a 30-degree demonstrator. Although the baseline of the project is centered on cos$\theta$-type magnets, we are working on an alternative strategy to mitigate the risk of failure in the construction of the demonstrator. This is a block coil type solution to avoid, with a simpler geometry, the difficulties of winding a curved cos$\theta$ dipole with significantly small curvature radius. In this context, an innovative winding technique was developed and tests have been conducted to confirm its feasibility. This contribution presents the results obtained from the winding tests in order to show the effectiveness of the method adopted to wind this type of coils and highlight possible improvements. In addition, an electromagnetic design concept for curved block coil dipoles has been developed, with the intention of proposing an optimized solution for the geometry of the coils, along with the method they can be wound.
- 19 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Consolidated 2D Mechanical Design and Preliminary 3D Design Phase of the Superconducting Ion Gantry (SIG) Dipole for Hadrontherapy
In ion therapy, gantries play a crucial role in minimizing damage to healthy tissue and enabling treatment from diverse angles. The introduction of superconducting magnets results in a substantial reduction in the overall weight and the power required to operate of these otherwise huge structures. The Superconducting Ion Gantry (SIG) project represents the contribution of INFN (Istituto Nazionale di Fisica Nucleare) to the EuroSIG collaboration, which includes CERN, CNAO (Centro Nazionale di Adroterapia Oncologica), and MedAustron. The primary goal is to design, manufacture, and test a demonstrator for a curved superconducting dipole with costheta-type NbTi coils for a 430 MeV/u carbon ion gantry. The magnet is designed with a 1.65 m radius of curvature and an 80 mm aperture, aiming to generate a magnetic field up to 4 T, with a ramp rate of about 0.4 T/s, without the option of utilizing a direct cooling system. The winding, assembly, and testing of the magnet will be carried out in Milan, at LASA (Laboratorio Acceleratori e Superconduttività Applicata). However, the available press is insufficient in size compared to the dimensions of the magnet. To overcome this limitation, an alternative method has been devised for the assembly of the iron yoke, relying on a steel system of clamps and vertical tie rods. These clamps have the purpose of securely fastening the two yoke halves together. This study presents the final design of the mechanical structure cross-section, derived through finite element analyses, highlighting the optimization of mechanical contacts between components while adhering to structural limits. Additionally, a preliminary 3D design based on this optimized cross-section is introduced.
- 19 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Consolidated 2D Mechanical Design and Preliminary 3D Design Phase of the Superconducting Ion Gantry (SIG) Dipole for Hadrontherapy
In ion therapy, gantries play a crucial role in minimizing damage to healthy tissue and enabling treatment from diverse angles. The introduction of superconducting magnets results in a substantial reduction in the overall weight and the power required to operate of these otherwise huge structures. The Superconducting Ion Gantry (SIG) project represents the contribution of INFN (Istituto Nazionale di Fisica Nucleare) to the EuroSIG collaboration, which includes CERN, CNAO (Centro Nazionale di Adroterapia Oncologica), and MedAustron. The primary goal is to design, manufacture, and test a demonstrator for a curved superconducting dipole with costheta-type NbTi coils for a 430 MeV/u carbon ion gantry. The magnet is designed with a 1.65 m radius of curvature and an 80 mm aperture, aiming to generate a magnetic field up to 4 T, with a ramp rate of about 0.4 T/s, without the option of utilizing a direct cooling system. The winding, assembly, and testing of the magnet will be carried out in Milan, at LASA (Laboratorio Acceleratori e Superconduttività Applicata). However, the available press is insufficient in size compared to the dimensions of the magnet. To overcome this limitation, an alternative method has been devised for the assembly of the iron yoke, relying on a steel system of clamps and vertical tie rods. These clamps have the purpose of securely fastening the two yoke halves together. This study presents the final design of the mechanical structure cross-section, derived through finite element analyses, highlighting the optimization of mechanical contacts between components while adhering to structural limits. Additionally, a preliminary 3D design based on this optimized cross-section is introduced.
- 2 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
First Winding Trial for the Superconducting Ion Gantry (SIG) Dipole Demonstrator Magnet
The Superconducting Ion Gantry (SIG) project aims to design, construct, and test a curved superconducting dipole demonstrator magnet for an ion gantry (up to a rigidity of 6.6 Tm). The main demonstrator magnet parameters are a dipolar field of 4 T generated into a toroidal aperture with an 80 mm diameter, 1.65 m curvature radius, and 30° angular sector. The project is inserted in the framework of the EuroSIG collaboration among CNAO, CERN, INFN, and MedAustron. Within this collaboration, the main goal of SIG is to perform a feasibility study of winding and assembling cos- $\theta$ coils with a small curvature radius. In addition, a parallel program at CERN is dedicated to the study of the indirect cooling problem through the construction of a straight thermal demonstrator magnet sharing the SIG cross-section. The basic idea behind these programs is to check whether the vast experience of the community on superconducting accelerator magnets design can lead to a breakthrough in the gantry magnets domain. This article shows the main elements of the conceptual design of the SIG magnet and reports on the first winding trial performed at the LASA laboratory, in Milan, with a copper dummy cable. Moreover, possible solutions for the winding, curing, and impregnation of highly curved cos $\theta$ coils are discussed.
- 2 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
First Winding Trial for the Superconducting Ion Gantry (SIG) Dipole Demonstrator Magnet
The Superconducting Ion Gantry (SIG) project aims to design, construct, and test a curved superconducting dipole demonstrator magnet for an ion gantry (up to a rigidity of 6.6 Tm). The main demonstrator magnet parameters are a dipolar field of 4 T generated into a toroidal aperture with an 80 mm diameter, 1.65 m curvature radius, and 30° angular sector. The project is inserted in the framework of the EuroSIG collaboration among CNAO, CERN, INFN, and MedAustron. Within this collaboration, the main goal of SIG is to perform a feasibility study of winding and assembling cos- $\theta$ coils with a small curvature radius. In addition, a parallel program at CERN is dedicated to the study of the indirect cooling problem through the construction of a straight thermal demonstrator magnet sharing the SIG cross-section. The basic idea behind these programs is to check whether the vast experience of the community on superconducting accelerator magnets design can lead to a breakthrough in the gantry magnets domain. This article shows the main elements of the conceptual design of the SIG magnet and reports on the first winding trial performed at the LASA laboratory, in Milan, with a copper dummy cable. Moreover, possible solutions for the winding, curing, and impregnation of highly curved cos $\theta$ coils are discussed.