Klara Kiselman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Klara Kiselman has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Jan Keller
Ångström Laboratory Division of Solar Cell Technology Uppsala University Uppsala Sweden
2 shared publications Lars Stolt
Uppsala University
2 shared publications- Marika Edoff
Uppsala University
2 shared publications - Olivier Donzel-Gargand
Uppsala University
2 shared publications - André Filipe Violas
International Iberian Nanotechnology Laboratory
1 shared publication - Elizaveta Yakovleva Bengtson
Uppsala Universitet
1 shared publication
Latest Publications
- Open Access
- 1 July 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 16 (4) , 415-420
Back Contact Passivation With Ga-Grading in Narrow Bandgap (Ag,Cu)(In,Ga)Se 2 Bifacial Solar Cells on In 2 O 3 :Sn Back Contact
- 1 July 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 16 (4) , 415-420
Open AccessBack Contact Passivation With Ga-Grading in Narrow Bandgap (Ag,Cu)(In,Ga)Se 2 Bifacial Solar Cells on In 2 O 3 :Sn Back Contact
- Open Access
- 4 May 2025
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 33 (7) , 735-746
Light‐Soaking Effects in High‐Efficiency Cu(In,Ga)Se2 and (Ag,Cu)(In,Ga)Se2 Solar Cells
Metastable behaviours with respect to light‐soaking of Cu(In,Ga)Se2 (CIGS) solar cells have long been known and studied, but no explanation has yet been fully agreed on. In this study, silver alloying and its impact on light‐soaking effects is explored in four CIGS and six (Ag,Cu)(In,Ga)Se2 (ACIGS) samples with high efficiency (17% to 21% before light‐soaking). All were produced by co‐evaporation and similar depositions protocols as the current world record device but with some variation. A variety of opto‐electronic characterisation methods were used to explore the response to 24 h of light‐soaking at 50°C. We found that (i) the open‐circuit voltage increased for all ACIGS devices but decreased for the CIGS devices, (ii) the cells entered a state with higher doping and more tail states, and (iii) the effect was metastable and partially reverted after dark storage. While the improvement of the ACIGS cells saturates after 24 h in one‐third of the irradiance at one sun, months are needed to reverse the open‐circuit voltage change. Despite a higher doping after light‐soaking, none of the samples' short‐circuit current showed significant changes and the efficiency after light‐soaking ranged from 15% to 22%. No long‐range change in sodium or rubidium distributions was observed using glow‐discharge optical emission spectroscopy. In general, external radiative efficiency measurements showed that the nonradiative recombination loss is reduced after light‐soaking in the ACIGS devices. However, the correlation to the measured voltage was not always straight forward, presumably due to the graded bandgap of the absorber.
- 4 May 2025
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 33 (7) , 735-746
Open AccessLight‐Soaking Effects in High‐Efficiency Cu(In,Ga)Se2 and (Ag,Cu)(In,Ga)Se2 Solar Cells
Metastable behaviours with respect to light‐soaking of Cu(In,Ga)Se2 (CIGS) solar cells have long been known and studied, but no explanation has yet been fully agreed on. In this study, silver alloying and its impact on light‐soaking effects is explored in four CIGS and six (Ag,Cu)(In,Ga)Se2 (ACIGS) samples with high efficiency (17% to 21% before light‐soaking). All were produced by co‐evaporation and similar depositions protocols as the current world record device but with some variation. A variety of opto‐electronic characterisation methods were used to explore the response to 24 h of light‐soaking at 50°C. We found that (i) the open‐circuit voltage increased for all ACIGS devices but decreased for the CIGS devices, (ii) the cells entered a state with higher doping and more tail states, and (iii) the effect was metastable and partially reverted after dark storage. While the improvement of the ACIGS cells saturates after 24 h in one‐third of the irradiance at one sun, months are needed to reverse the open‐circuit voltage change. Despite a higher doping after light‐soaking, none of the samples' short‐circuit current showed significant changes and the efficiency after light‐soaking ranged from 15% to 22%. No long‐range change in sodium or rubidium distributions was observed using glow‐discharge optical emission spectroscopy. In general, external radiative efficiency measurements showed that the nonradiative recombination loss is reduced after light‐soaking in the ACIGS devices. However, the correlation to the measured voltage was not always straight forward, presumably due to the graded bandgap of the absorber.
- Top Cited PapersOpen Access
- 19 February 2024
- Published by Springer Nature in Nature Energy
- Vol. 9 (4) , 467-478
High-concentration silver alloying and steep back-contact gallium grading enabling copper indium gallium selenide solar cell with 23.6% efficiency
Chalcopyrite-based solar cells have reached an efficiency of 23.35%, yet further improvements have been challenging. Here we present a 23.64% certified efficiency for a (Ag,Cu)(In,Ga)Se2solar cell, achieved through the implementation of a series of strategies. We introduce a relatively high amount of silver ([Ag]/([Ag] + [Cu]) = 0.19) into the absorber and implement a ‘hockey stick’-like gallium profile with a high concentration of Ga close to the molybdenum back contact and a lower, constant concentration in the region closer to the CdS buffer layer. This kind of elemental profile minimizes lateral and in-depth bandgap fluctuations, reducing losses in open-circuit voltage. In addition, the resulting bandgap energy is close to the local optimum of 1.15 eV. We apply a RbF post-deposition treatment that leads to the formation of a Rb–In–Se phase, probably RbInSe2, passivating the absorber surface. Finally, we discuss future research directions to reach 25% efficiency.
- 19 February 2024
- Published by Springer Nature in Nature Energy
- Vol. 9 (4) , 467-478
Top Cited PapersOpen AccessHigh-concentration silver alloying and steep back-contact gallium grading enabling copper indium gallium selenide solar cell with 23.6% efficiency
Chalcopyrite-based solar cells have reached an efficiency of 23.35%, yet further improvements have been challenging. Here we present a 23.64% certified efficiency for a (Ag,Cu)(In,Ga)Se2solar cell, achieved through the implementation of a series of strategies. We introduce a relatively high amount of silver ([Ag]/([Ag] + [Cu]) = 0.19) into the absorber and implement a ‘hockey stick’-like gallium profile with a high concentration of Ga close to the molybdenum back contact and a lower, constant concentration in the region closer to the CdS buffer layer. This kind of elemental profile minimizes lateral and in-depth bandgap fluctuations, reducing losses in open-circuit voltage. In addition, the resulting bandgap energy is close to the local optimum of 1.15 eV. We apply a RbF post-deposition treatment that leads to the formation of a Rb–In–Se phase, probably RbInSe2, passivating the absorber surface. Finally, we discuss future research directions to reach 25% efficiency.