Iason Rossetos
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Iason Rossetos has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Charis J. Gantes
National Technical University of Athens
1 shared publication- Charis J. Gantes
National Technical University of Athens
1 shared publication Dimitrios Galanis
National and Kapodistrian University of Athens
1 shared publication- Dimitrios Galanis
First Department of Orthopaedics, Attiko Hospital, School of Medicine, National and Kapodistrian University of Athens, 15772 Athens, Greece
1 shared publication - Fani Pliarchopoulou
School of Medicine, National and Kapodistrian University of Athens, 115 27 Athens, Greece
1 shared publication George Kazakis
National Technical University of Athens
1 shared publication
Latest Publications
- 25 June 2025
- Published by Springer Nature
- p. 245-254
Advanced Numerical Simulation of a 3D-Printed Spinal Brace
- 25 June 2025
- Published by Springer Nature
- p. 245-254
Advanced Numerical Simulation of a 3D-Printed Spinal Brace
- Open Access
- 21 February 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (5) , 1735
Numerical Modeling and Nonlinear Finite Element Analysis of Conventional and 3D-Printed Spinal Braces
This study aims to describe the numerical modeling and nonlinear finite element analysis of typical spinal braces as a first step towards optimizing their topology for 3D printing. Numerical simulation was carried out in Abaqus CAE software Version 2021, utilizing a CAD (Meshmixer Version 3.5.474) scan of an actual spinal brace. Boundary conditions were defined by means of contact surfaces between the human body and the supporting pads located in the interior of the brace. The process of tightening the straps on the rear face of the brace was simulated via appropriate imposed displacements. The response is described through the deformations and developing stresses of the brace and the contact pressures in the areas of interaction with the human body. Parametric analysis indicated that increasing the cross-sectional thickness or elastic modulus of the brace material results in higher maximum von Mises stresses and lower displacements. The comparison between 3D-printed and conventional braces highlighted the potential of 3D-printing technology to achieve comparable performance with customized designs, leveraging the constitutive properties of 3D-printed material obtained from tension tests. The tension tests demonstrated that the 3D-printed material achieved higher values of modulus of elasticity compared to traditional brace materials. Finally, the topology optimization criteria to be applied for the design of spinal braces in the next step of this ongoing research are briefly described.
- 21 February 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (5) , 1735
Open AccessNumerical Modeling and Nonlinear Finite Element Analysis of Conventional and 3D-Printed Spinal Braces
This study aims to describe the numerical modeling and nonlinear finite element analysis of typical spinal braces as a first step towards optimizing their topology for 3D printing. Numerical simulation was carried out in Abaqus CAE software Version 2021, utilizing a CAD (Meshmixer Version 3.5.474) scan of an actual spinal brace. Boundary conditions were defined by means of contact surfaces between the human body and the supporting pads located in the interior of the brace. The process of tightening the straps on the rear face of the brace was simulated via appropriate imposed displacements. The response is described through the deformations and developing stresses of the brace and the contact pressures in the areas of interaction with the human body. Parametric analysis indicated that increasing the cross-sectional thickness or elastic modulus of the brace material results in higher maximum von Mises stresses and lower displacements. The comparison between 3D-printed and conventional braces highlighted the potential of 3D-printing technology to achieve comparable performance with customized designs, leveraging the constitutive properties of 3D-printed material obtained from tension tests. The tension tests demonstrated that the 3D-printed material achieved higher values of modulus of elasticity compared to traditional brace materials. Finally, the topology optimization criteria to be applied for the design of spinal braces in the next step of this ongoing research are briefly described.