Madeleine Weigel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Madeleine Weigel has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
- Norbert Keil
Fraunhofer Institute for Telecommunications, Heinrich-Hertz-Institute, HHI, Einsteinufer 37, 10587 Berlin, Germany
9 shared publications - Moritz Kleinert
Fraunhofer Institute for Telecommunications, Heinrich-Hertz-Institute, HHI, Einsteinufer 37, 10587 Berlin, Germany
8 shared publications - David de Felipe
Fraunhofer Institute for Telecommunications, Heinrich-Hertz-Institut, Berlin, Germany
7 shared publications - Hercules Avramopoulos
National Technical University of Athens
5 shared publications - Martin Schell
Fraunhofer Institute for Telecommunications, Heinrich Hertz Institute, Berlin, Germany
5 shared publications - Crispin Zawadzki
Fraunhofer Institute for Telecommunications, Heinrich-Hertz-Institute, HHI, Einsteinufer 37, 10587 Berlin, Germany
4 shared publications
Latest Publications
- 16 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 38 (10) , 683-686
System-Level Demonstration of a 3D-Integrated Optical 16×16 Benes Switch
In this work, we present the first fully packaged $16\times 16$ Benes optical switch based on 3D photonic integration operating in the O-band, and demonstrate, for the first time, its system-level evaluation. The 3D switch employs a dual-layer architecture with 56 thermo-optic $2\times 2$ Mach-Zehnder interferometer-based crossbar units and vertical multimode interferometers enabling the transition between the two parallel waveguiding layers and effectively eliminating in-plane waveguide crossings. The static optical performance of the 3D optical switch prototype was evaluated based on insertion and polarization-dependent losses, crosstalk, power consumption, and switching speed. The 3D switch is fabricated on a polymer-based photonic platform, known as PolyBoard, which is suitable for developing 3D structures. In order to perform a system-level demonstration, the switch was integrated into a 25 Gb/s full-duplex optical link using a commercial Network Interface Card and SFP transceivers. Stable throughput was maintained across back-to-back and extended-reach fiber links up to 10 km, demonstrating the viability of this 3D-integrated switch for scalable, energy-efficient intra-data center interconnect.
- 16 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 38 (10) , 683-686
System-Level Demonstration of a 3D-Integrated Optical 16×16 Benes Switch
In this work, we present the first fully packaged $16\times 16$ Benes optical switch based on 3D photonic integration operating in the O-band, and demonstrate, for the first time, its system-level evaluation. The 3D switch employs a dual-layer architecture with 56 thermo-optic $2\times 2$ Mach-Zehnder interferometer-based crossbar units and vertical multimode interferometers enabling the transition between the two parallel waveguiding layers and effectively eliminating in-plane waveguide crossings. The static optical performance of the 3D optical switch prototype was evaluated based on insertion and polarization-dependent losses, crosstalk, power consumption, and switching speed. The 3D switch is fabricated on a polymer-based photonic platform, known as PolyBoard, which is suitable for developing 3D structures. In order to perform a system-level demonstration, the switch was integrated into a 25 Gb/s full-duplex optical link using a commercial Network Interface Card and SFP transceivers. Stable throughput was maintained across back-to-back and extended-reach fiber links up to 10 km, demonstrating the viability of this 3D-integrated switch for scalable, energy-efficient intra-data center interconnect.
- Open Access
Hybrid Photonic Integrated Circuits for Wireless Transceivers
Recent advancements in hybrid photonic integrated circuits (PICs) for wireless communications are reviewed, with a focus on innovations developed at Fraunhofer HHI. This work leverages hybrid integration technology, which combines indium phosphide (InP) active elements, silicon nitride (Si3N4) low-loss waveguides, and high-efficient thermal-optical tunable polymers with micro-optical functions to achieve fully integrated wireless transceivers. Key contributions include (1) On-chip optical injection locking for generating phase-locked optical beat notes at 45 GHz, enabled by cascaded InP phase modulators and hybrid InP/polymer tunable lasers with a 3.8 GHz locking range. (2) Waveguide-integrated THz emitters and receivers, featuring photoconductive antennas (PCAs) with a 22× improved photoresponse compared to top-illuminated designs, alongside scalable 1 × 4 PIN-PD and PCA arrays for enhanced power and directivity. (3) Beam steering at 300 GHz using a polymer-based optical phased array (OPA) integrated with an InP antenna array, achieving continuous steering across 20° and a 10.6 dB increase in output power. (4) Demonstration of fully integrated hybrid wireless transceiver PICs combining InP, Si3N4, and polymer material platforms, validated through key component characterization, on-chip optical frequency comb generation, and coherent beat note generation at 45 GHz. These advancements result in compact form factors, reduced power consumption, and enhanced scalability, positioning PICs as an enabling technology for future high-speed wireless networks.
Open AccessHybrid Photonic Integrated Circuits for Wireless Transceivers
Recent advancements in hybrid photonic integrated circuits (PICs) for wireless communications are reviewed, with a focus on innovations developed at Fraunhofer HHI. This work leverages hybrid integration technology, which combines indium phosphide (InP) active elements, silicon nitride (Si3N4) low-loss waveguides, and high-efficient thermal-optical tunable polymers with micro-optical functions to achieve fully integrated wireless transceivers. Key contributions include (1) On-chip optical injection locking for generating phase-locked optical beat notes at 45 GHz, enabled by cascaded InP phase modulators and hybrid InP/polymer tunable lasers with a 3.8 GHz locking range. (2) Waveguide-integrated THz emitters and receivers, featuring photoconductive antennas (PCAs) with a 22× improved photoresponse compared to top-illuminated designs, alongside scalable 1 × 4 PIN-PD and PCA arrays for enhanced power and directivity. (3) Beam steering at 300 GHz using a polymer-based optical phased array (OPA) integrated with an InP antenna array, achieving continuous steering across 20° and a 10.6 dB increase in output power. (4) Demonstration of fully integrated hybrid wireless transceiver PICs combining InP, Si3N4, and polymer material platforms, validated through key component characterization, on-chip optical frequency comb generation, and coherent beat note generation at 45 GHz. These advancements result in compact form factors, reduced power consumption, and enhanced scalability, positioning PICs as an enabling technology for future high-speed wireless networks.
- Open Access
- 18 March 2025
- Published by MDPI AG in Preprints.org
Hybrid Photonic Integrated Circuits for Wireless Transceivers
Recently developed photonic integrated circuits (PICs) for wireless communications are reviewed. These PICs leverage hybrid integration technology, which combines InP active elements, silicon nitride (Si3N4) low-loss waveguides, high-efficient ther-mal-optical tunable polymer with micro-optical functions to achieve fully integrated systems. This approach incorporates photonic building blocks, such as tunable lasers, on-chip optical isolators, optical phased arrays (OPAs), modulators, semiconductor optical amplifiers (SOAs), PIN-photodiodes, and waveguide-based photoconductive antennas. Among the key innovations are the generation of phase-locked optical sig-nals for wireless carrier at 45 GHz through on-chip frequency comb generation and injection locking, as well as the photonic-enabled beam steering across 20° at 300 GHz by integrating polymer-based optical phased arrays with InP PIN-photodiode-based antenna arrays. These advancements result in compact form factors, reduced power consumption, and enhanced scalability, positioning PICs as an enabling technology for future high-speed wireless networks.
- 18 March 2025
- Published by MDPI AG in Preprints.org
Open AccessHybrid Photonic Integrated Circuits for Wireless Transceivers
Recently developed photonic integrated circuits (PICs) for wireless communications are reviewed. These PICs leverage hybrid integration technology, which combines InP active elements, silicon nitride (Si3N4) low-loss waveguides, high-efficient ther-mal-optical tunable polymer with micro-optical functions to achieve fully integrated systems. This approach incorporates photonic building blocks, such as tunable lasers, on-chip optical isolators, optical phased arrays (OPAs), modulators, semiconductor optical amplifiers (SOAs), PIN-photodiodes, and waveguide-based photoconductive antennas. Among the key innovations are the generation of phase-locked optical sig-nals for wireless carrier at 45 GHz through on-chip frequency comb generation and injection locking, as well as the photonic-enabled beam steering across 20° at 300 GHz by integrating polymer-based optical phased arrays with InP PIN-photodiode-based antenna arrays. These advancements result in compact form factors, reduced power consumption, and enhanced scalability, positioning PICs as an enabling technology for future high-speed wireless networks.
- Open Access
Repeatable Passive Fiber Optic Coupling of Single-Mode Waveguides in High-Precision Disposable Photonic Biosensors
This research demonstrates a method for the repeatable passive fiber optic coupling of single-mode waveguides with a micron-scale accuracy for high-precision disposables. The aim is to broaden the application of photonic integrated circuits (PICs) from traditional fiber optic communication systems to include medical, life science, and environmental sensing applications. The proposed passive coupling system enables the straightforward and reliable interchange of disposable photonic chips without manual read-out unit adjustments. Robustness is attributed to the chip-side grating couplers with 3 dB coupling tolerances exceeding ± 25 µm and a mechanical three-groove kinematic method ensuring precise alignment. The system simplicity is highlighted by the simple manual insertion and fixation of silicon nitride (Si3N4) PICs on a carrier using magnetic force and passive alignment features. Testing on a batch of 99 identical yet independent units revealed a standard deviation (SD) of 5.1 dB in coupling loss, without realignment post-calibration. This eliminates the need for active alignment processes, showing its potential for enabling field use. A usability assessment with five untrained operators confirms the suitability for various end-users, with consistent performance in engaging and disengaging disposable PICs. The research significantly advances the integration of photonic sensor technology into practical applications, particularly for chemical and biological fluid analysis in point-of-care settings.
Open AccessRepeatable Passive Fiber Optic Coupling of Single-Mode Waveguides in High-Precision Disposable Photonic Biosensors
This research demonstrates a method for the repeatable passive fiber optic coupling of single-mode waveguides with a micron-scale accuracy for high-precision disposables. The aim is to broaden the application of photonic integrated circuits (PICs) from traditional fiber optic communication systems to include medical, life science, and environmental sensing applications. The proposed passive coupling system enables the straightforward and reliable interchange of disposable photonic chips without manual read-out unit adjustments. Robustness is attributed to the chip-side grating couplers with 3 dB coupling tolerances exceeding ± 25 µm and a mechanical three-groove kinematic method ensuring precise alignment. The system simplicity is highlighted by the simple manual insertion and fixation of silicon nitride (Si3N4) PICs on a carrier using magnetic force and passive alignment features. Testing on a batch of 99 identical yet independent units revealed a standard deviation (SD) of 5.1 dB in coupling loss, without realignment post-calibration. This eliminates the need for active alignment processes, showing its potential for enabling field use. A usability assessment with five untrained operators confirms the suitability for various end-users, with consistent performance in engaging and disengaging disposable PICs. The research significantly advances the integration of photonic sensor technology into practical applications, particularly for chemical and biological fluid analysis in point-of-care settings.
- Open Access
- 20 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 36 (7) , 469-472
Sparse Aperiodic Optical Phased Arrays on Polymer Integration Platform
We demonstrate solid-state optical beam-steering utilizing polymer waveguides as edge emitters to form optical phased arrays (OPAs) for operation at 1550 nm. Waveguide spacing below the wavelength is hindered in low index contrast OPAs by cross-coupling, leading to the formation of unwanted grating lobes in the far field. We employ non-uniform spacing between the 16 channels of the OPAs to suppress the grating lobes and improve the unambiguous beam steering range. Three different aperiodic layouts are fabricated and experimentally tested. Within a steering range of ±10° we achieve an average beamwidth of 0.45° with an ordered spacing layout, and 0.52° and 0.69° with a randomized spacing layout of$8\lambda $ and$5\lambda $ average spacing, respectively. With the latter we show suppression of the sidelobes of >11 dB and >6 dB within a steering range of ±5° and ±8°, accordingly. Power consumption of 1.28 mW/$\pi $ per channel is achieved thanks to the excellent thermo-optic (TO) coefficient of the polymer platform. To the best of our knowledge, we are the first to demonstrate polymer-based OPAs with aperiodic spacing.- 20 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 36 (7) , 469-472
Open AccessSparse Aperiodic Optical Phased Arrays on Polymer Integration Platform
We demonstrate solid-state optical beam-steering utilizing polymer waveguides as edge emitters to form optical phased arrays (OPAs) for operation at 1550 nm. Waveguide spacing below the wavelength is hindered in low index contrast OPAs by cross-coupling, leading to the formation of unwanted grating lobes in the far field. We employ non-uniform spacing between the 16 channels of the OPAs to suppress the grating lobes and improve the unambiguous beam steering range. Three different aperiodic layouts are fabricated and experimentally tested. Within a steering range of ±10° we achieve an average beamwidth of 0.45° with an ordered spacing layout, and 0.52° and 0.69° with a randomized spacing layout of$8\lambda $ and$5\lambda $ average spacing, respectively. With the latter we show suppression of the sidelobes of >11 dB and >6 dB within a steering range of ±5° and ±8°, accordingly. Power consumption of 1.28 mW/$\pi $ per channel is achieved thanks to the excellent thermo-optic (TO) coefficient of the polymer platform. To the best of our knowledge, we are the first to demonstrate polymer-based OPAs with aperiodic spacing. - Open Access
- 13 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (5) , 1511-1517
Design and Fabrication of Crossing-Free Waveguide Routing Networks Using a Multi-Layer Polymer-Based Photonic Integration Platform
A novel 16×4 crossing-free waveguide routing network on four layers of polymer-based stacked waveguides is presented. The design combines in-plane passive waveguide devices with vertical multimode interference couplers (1×1 3D MMIs) to connect two adjacent waveguide layers. The 16×4 multilayer waveguide routing network (MWRN) is fabricated using multilayer deposition and standard UV contact lithography. A novel fabrication method of multiple waveguide layers that includes a sequence for wafer planarization steps to reduce topographies is presented. These developments lead to a reproducible multi-layer device fabricated on wafer-scale. Our technology enables a high vertical spacing of 21.6 μm (center-to-center) between the top and bottom waveguide layers with a large waveguide-to-waveguide spacing of 7.2 μm (center-to-center). The complex 16×4 MWRN can serve as the crossing-free waveguide routing for a 4×4 3D optical switch.
- 13 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (5) , 1511-1517
Open AccessDesign and Fabrication of Crossing-Free Waveguide Routing Networks Using a Multi-Layer Polymer-Based Photonic Integration Platform
A novel 16×4 crossing-free waveguide routing network on four layers of polymer-based stacked waveguides is presented. The design combines in-plane passive waveguide devices with vertical multimode interference couplers (1×1 3D MMIs) to connect two adjacent waveguide layers. The 16×4 multilayer waveguide routing network (MWRN) is fabricated using multilayer deposition and standard UV contact lithography. A novel fabrication method of multiple waveguide layers that includes a sequence for wafer planarization steps to reduce topographies is presented. These developments lead to a reproducible multi-layer device fabricated on wafer-scale. Our technology enables a high vertical spacing of 21.6 μm (center-to-center) between the top and bottom waveguide layers with a large waveguide-to-waveguide spacing of 7.2 μm (center-to-center). The complex 16×4 MWRN can serve as the crossing-free waveguide routing for a 4×4 3D optical switch.
- 5 March 2022
- Published by SPIE-Intl Soc Optical Eng
- p. 9
Hybrid photonic integration for communication, sensing and quantum technology
SPIE Digital Library Proceedings
- 5 March 2022
- Published by SPIE-Intl Soc Optical Eng
- p. 9
Hybrid photonic integration for communication, sensing and quantum technology
SPIE Digital Library Proceedings
- Open Access
- 26 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 39 (20) , 6509-6523
2D Optical Phased Arrays for Laser Beam Steering Based On 3D Polymer Photonic Integrated Circuits
We propose a novel concept for the implementation of 2-dimensional (2D) optical phased arrays (OPAs) with end-fire waveguides as antenna elements (AEs), and we present its theoretical model and experimental proof. The concept is based on the use of 3-dimensional (3D) photonic integrated circuits (PICs) with multiple waveguiding layers on the PolyBoard platform. In their simplest form, the 3D PICs comprise AEs at different layers, vertical and lateral couplers for the distribution of light among the AEs, and phase shifters for the execution of the 2D beam scanning process. Using the field equivalence principle, we model the radiated field from the single-mode waveguide of the platform at 1550 nm, and we find that the expected beam width is 12.7°. We also investigate the perturbation that is induced into propagating fields inside parallel waveguides in proximity, and we conclude that waveguide spacings down to 6 µm can be safely used for development of uniform OPAs in the PolyBoard platform. For OPAs with 6 µm pitch and 4 AEs, we find that the maximum steering angle is 14.0° and the expected angular clearance, wherein the main radiation lobe is higher than any grating lobe by at least 3, 6 and 10 dB is 10.8°, 7.6° and 2.8°, respectively. Based on our simulations, we design and fabricate single- and 2-layer PICs with 1 × 4 and 2 × 4 OPAs. The lateral pitch of the OPAs ranges from 10 down to 6 µm, while the vertical pitch is 7.2 µm. We experimentally characterize these OPAs and validate the potential of the 2-layer PICs for 2D beam scanning on the azimuthal and elevation plane. The beam profiles and the main scanning parameters such as the maximum steering angle and the relative intensity between the main and the grating lobes are found in excellent agreement with our simulations.
- 26 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 39 (20) , 6509-6523
Open Access2D Optical Phased Arrays for Laser Beam Steering Based On 3D Polymer Photonic Integrated Circuits
We propose a novel concept for the implementation of 2-dimensional (2D) optical phased arrays (OPAs) with end-fire waveguides as antenna elements (AEs), and we present its theoretical model and experimental proof. The concept is based on the use of 3-dimensional (3D) photonic integrated circuits (PICs) with multiple waveguiding layers on the PolyBoard platform. In their simplest form, the 3D PICs comprise AEs at different layers, vertical and lateral couplers for the distribution of light among the AEs, and phase shifters for the execution of the 2D beam scanning process. Using the field equivalence principle, we model the radiated field from the single-mode waveguide of the platform at 1550 nm, and we find that the expected beam width is 12.7°. We also investigate the perturbation that is induced into propagating fields inside parallel waveguides in proximity, and we conclude that waveguide spacings down to 6 µm can be safely used for development of uniform OPAs in the PolyBoard platform. For OPAs with 6 µm pitch and 4 AEs, we find that the maximum steering angle is 14.0° and the expected angular clearance, wherein the main radiation lobe is higher than any grating lobe by at least 3, 6 and 10 dB is 10.8°, 7.6° and 2.8°, respectively. Based on our simulations, we design and fabricate single- and 2-layer PICs with 1 × 4 and 2 × 4 OPAs. The lateral pitch of the OPAs ranges from 10 down to 6 µm, while the vertical pitch is 7.2 µm. We experimentally characterize these OPAs and validate the potential of the 2-layer PICs for 2D beam scanning on the azimuthal and elevation plane. The beam profiles and the main scanning parameters such as the maximum steering angle and the relative intensity between the main and the grating lobes are found in excellent agreement with our simulations.
- Open Access
- 21 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 39 (7) , 2123-2129
Second Harmonic Generation in Polymer Photonic Integrated Circuits
Second harmonic generation is an efficient way to create coherent radiation at wavelengths that are not accessible with standard laser sources. In this work we demonstrate second harmonic generation from 1550 nm to 775 nm in a polymer photonic integrated circuit via the hybrid integration of a periodically poled lithium niobate crystal. The bulk crystal is inserted in an on-chip free-space section between two waveguide coupled GRIN lenses. Fiber to fiber conversion efficiencies were 0.03 %/W for a continuous wave laser source and 100 %/W for a femtosecond laser source. Furthermore, third and fourth harmonic light at 517 nm and 388 nm was observed.
- 21 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 39 (7) , 2123-2129
Open AccessSecond Harmonic Generation in Polymer Photonic Integrated Circuits
Second harmonic generation is an efficient way to create coherent radiation at wavelengths that are not accessible with standard laser sources. In this work we demonstrate second harmonic generation from 1550 nm to 775 nm in a polymer photonic integrated circuit via the hybrid integration of a periodically poled lithium niobate crystal. The bulk crystal is inserted in an on-chip free-space section between two waveguide coupled GRIN lenses. Fiber to fiber conversion efficiencies were 0.03 %/W for a continuous wave laser source and 100 %/W for a femtosecond laser source. Furthermore, third and fourth harmonic light at 517 nm and 388 nm was observed.